| /linux/tools/perf/pmu-events/arch/x86/alderlaken/ |
| H A D | cache.json | |
| /linux/drivers/clk/ |
| H A D | clk-fractional-divider_test.c | 29 parent_rate = (max_n + 1) * rate; /* so that it exceeds the maximum divisor */ in clk_fd_test_approximation_max_denominator()
58 parent_rate = rate / (max_m + 1); /* so that it exceeds the maximum numerator */ in clk_fd_test_approximation_max_numerator()
88 parent_rate = (max_n + 1) * rate; /* so that it exceeds the maximum divisor */ in clk_fd_test_approximation_max_denominator_zero_based()
118 parent_rate = rate / (max_m + 1); /* so that it exceeds the maximum numerator */ in clk_fd_test_approximation_max_numerator_zero_based()
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-event_source-devices-hv_gpci | 114 * "-EFBIG" : System information exceeds PAGE_SIZE.
146 * "-EFBIG" : System information exceeds PAGE_SIZE.
178 * "-EFBIG" : System information exceeds PAGE_SIZE.
210 * "-EFBIG" : System information exceeds PAGE_SIZE.
242 * "-EFBIG" : System information exceeds PAGE_SIZE.
|
| H A D | sysfs-driver-intel-i915-hwmon | 17 exceeds this limit. A read value of 0 means that the PL1
48 operating frequency if the power averaged over a window exceeds
62 exceeds this limit.
|
| /linux/drivers/crypto/caam/ |
| H A D | error.c | 117 { 0xF1, "3GPP HFN matches or exceeds the Threshold" },
131 { 0x31, "DHR exceeds max. buffer size (allocate mode, S/G format)"},
132 { 0x32, "SGT exceeds max. buffer size (allocate mode, S/G format"},
135 { 0x35, "Length exceeds max. short length (allocate mode, S/G/ format)"},
136 { 0x36, "Memory footprint exceeds max. value (allocate mode, S/G/ format)"},
142 { 0x46, "Annotation length exceeds offset (reuse mode)"},
144 { 0x49, "Data offset correction exceeds input frame data length (reuse mode)"},
|
| /linux/Documentation/hwmon/ |
| H A D | adt7462.rst | 36 any measured value exceeds either limit.
70 temperature sensor associated with the PWM control exceeds temp#_max.
|
| H A D | w83792d.rst | 148 exceeds the high limit (T+tolerance), the fan will be turned on with a
152 (1) If the temperature still exceeds the high limit, PWM duty
160 slowly to 0 or a preset stop value until the temperature exceeds the low
|
| H A D | adt7470.rst | 35 limit values. The ADT7470 will signal an ALARM if any measured value exceeds
69 temperature sensor associated with the PWM control exceeds
|
| H A D | adt7475.rst | 71 any measured value exceeds either limit.
141 the PWM control exceeds temp#_max.
|
| /linux/tools/perf/Documentation/ |
| H A D | intel-acr.txt | 8 one event exceeds some threshold relative to the rate of another event,
21 In this case, if the "instructions" counter exceeds the sample period of
|
| /linux/tools/perf/pmu-events/arch/x86/alderlake/ |
| H A D | cache.json | |
| /linux/drivers/char/ |
| H A D | hangcheck-timer.c | 15 * checks whether it was delayed and if that delay exceeds a given
21 * actual duration that the timer waited. If the duration exceeds the
|
| /linux/drivers/char/agp/ |
| H A D | isoch.c | 156 "by AGP 3.0 devices exceeds that which is supported by " in agp_3_5_isochronous_node_enable()
192 "exceeds that which is supported by the AGP 3.0 " in agp_3_5_isochronous_node_enable()
228 /* Exit if the minimal RQ needs of the masters exceeds what the target in agp_3_5_isochronous_node_enable()
233 "AGP 3.0 devices exceeds the number provided by the " in agp_3_5_isochronous_node_enable()
|
| /linux/include/uapi/linux/netfilter/ipset/ |
| H A D | ip_set_bitmap.h | 11 /* The range exceeds the size limit of the set type */
|
| /linux/tools/net/sunrpc/xdrgen/tests/ |
| H A D | bad-version-number-too-large.x | 9 * version number 4294967296 in program 'BADPROG' exceeds 4294967295
|
| H A D | bad-program-number-too-large.x | 9 * program number 4294967296 in program 'BADPROG' exceeds 4294967295
|
| H A D | bad-procedure-number-too-large.x | 9 * procedure number 4294967296 in version 'BADVERS' exceeds 4294967295
|
| /linux/Documentation/devicetree/bindings/power/supply/ |
| H A D | rohm,bd99954.yaml | 92 # when battery voltage exceeds this limit voltage (3 in above chart)
103 # battery is expected to be faulty if battery voltage exceeds this limit.
|
| /linux/drivers/target/tcm_remote/ |
| H A D | tcm_remote.c | 105 pr_err("Passed tpgt: %lu exceeds TL_TPGS_PER_HBA: %u\n", in tcm_remote_make_tpg()
195 pr_err("Emulated NAA %s Address: %s, exceeds max: %d\n", in tcm_remote_make_wwn()
|
| /linux/Documentation/networking/ |
| H A D | udplite.rst | 127 if the specified coverage length exceeds the packet length, the packet
189 that for the second packet, the coverage length exceeds the packet
253 coverage length exceeds received length)
|
| /linux/init/ |
| H A D | version.c | 28 pr_warn("hostname parameter exceeds %zd characters and will be truncated", in early_hostname()
|
| /linux/drivers/platform/x86/hp/hp-bioscfg/ |
| H A D | biosattr-interface.c | 14 * were introduced that exceeds 128-byte data size. Changes to handle
110 * -EINVAL if the output buffer size exceeds buffersize
|
| /linux/Documentation/ABI/stable/ |
| H A D | sysfs-driver-ib_srp | 42 exceeds this limit after S/G list collapsing will fail.
55 ib_srp. Specifying a value that exceeds cmd_sg_entries is
|
| /linux/sound/hda/core/ |
| H A D | array.c | 14 * Get a new element from the given array. If it exceeds the
|
| /linux/tools/testing/selftests/tc-testing/ |
| H A D | tdc_gso.py | 31 parser.error("payload_len exceeds UDP_MAX_SEGMENTS")
|