| /freebsd/sys/contrib/device-tree/Bindings/edac/ |
| H A D | socfpga-eccmgr.txt | 1 Altera SoCFPGA ECC Manager
2 This driver uses the EDAC framework to implement the SOCFPGA ECC Manager.
3 The ECC Manager counts and corrects single bit errors and counts/handles
6 Cyclone5 and Arria5 ECC Manager
8 - compatible : Should be "altr,socfpga-ecc-manager"
9 - #address-cells: must be 1
10 - #size-cells: must be 1
11 - ranges : standard definition, should translate from local addresses
15 L2 Cache ECC
17 - compatible : Should be "altr,socfpga-l2-ecc"
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/mtd/ |
| H A D | mtk-nand.txt | 5 the nand controller interface driver and the ECC engine driver.
15 - compatible: Should be one of
16 "mediatek,mt2701-nfc",
17 "mediatek,mt2712-nfc",
18 "mediatek,mt7622-nfc".
19 - reg: Base physical address and size of NFI.
20 - interrupts: Interrupts of NFI.
21 - clocks: NFI required clocks.
22 - clock-names: NFI clocks internal name.
23 - ecc-engine: Required ECC Engine node.
[all …]
|
| H A D | hisi504-nand.txt | 5 - compatible: Should be "hisilicon,504-nfc".
6 - reg: The first contains base physical address and size of
8 physical address and size of NAND controller's buffer.
9 - interrupts: Interrupt number for nfc.
10 - nand-bus-width: See nand-controller.yaml.
11 - nand-ecc-mode: Support none and hw ecc mode.
12 - #address-cells: Partition address, should be set 1.
13 - #size-cells: Partition size, should be set 1.
17 - nand-ecc-strength: Number of bits to correct per ECC step.
18 - nand-ecc-step-size: Number of data bytes covered by a single ECC step.
[all …]
|
| H A D | mediatek,mtk-nfc.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/mediatek,mtk-nfc.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Xiangsheng Hou <xiangsheng.hou@mediatek.com>
15 - mediatek,mt2701-nfc
16 - mediatek,mt2712-nfc
17 - mediatek,mt7622-nfc
21 - description: Base physical address and size of NFI.
25 - description: NFI interrupt
[all …]
|
| H A D | brcm,brcmnand.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Brian Norris <computersforpeace@gmail.com>
11 - Kamal Dasu <kdasu.kdev@gmail.com>
12 - William Zhang <william.zhang@broadcom.com>
15 The Broadcom Set-Top Box NAND controller supports low-level access to raw NAND
16 flash chips. It has a memory-mapped register interface for both control
27 -- Additional SoC-specific NAND controller properties --
35 interesting ways, sometimes with registers that lump multiple NAND-related
[all …]
|
| H A D | gpmc-nand.txt | 7 explained in a separate documents - please refer to
8 Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
10 For NAND specific properties such as ECC modes or bus width, please refer to
11 Documentation/devicetree/bindings/mtd/nand-controller.yaml
16 - compatible: "ti,omap2-nand"
17 - reg: range id (CS number), base offset and length of the
19 - interrupts: Two interrupt specifiers, one for fifoevent, one for termcount.
23 - nand-bus-width: Set this numeric value to 16 if the hardware
27 - ti,nand-ecc-opt: A string setting the ECC layout to use. One of:
28 "sw" 1-bit Hamming ecc code via software
[all …]
|
| H A D | atmel-nand.txt | 4 Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt).
6 The NAND controller might be connected to an ECC engine.
11 - compatible: should be one of the following
12 "atmel,at91rm9200-nand-controller"
13 "atmel,at91sam9260-nand-controller"
14 "atmel,at91sam9261-nand-controller"
15 "atmel,at91sam9g45-nand-controller"
16 "atmel,sama5d3-nand-controller"
17 "microchip,sam9x60-nand-controller"
18 - ranges: empty ranges property to forward EBI ranges definitions.
[all …]
|
| H A D | marvell-nand.txt | 4 - compatible: can be one of the following:
5 * "marvell,armada-8k-nand-controller"
6 * "marvell,armada370-nand-controller"
7 * "marvell,pxa3xx-nand-controller"
8 * "marvell,armada-8k-nand" (deprecated)
9 * "marvell,armada370-nand" (deprecated)
10 * "marvell,pxa3xx-nand" (deprecated)
13 - reg: NAND flash controller memory area.
14 - #address-cells: shall be set to 1. Encode the NAND CS.
15 - #size-cells: shall be set to 0.
[all …]
|
| H A D | vf610-nfc.txt | 7 - compatible: Should be set to "fsl,vf610-nfc".
8 - reg: address range of the NFC.
9 - interrupts: interrupt of the NFC.
10 - #address-cells: shall be set to 1. Encode the nand CS.
11 - #size-cells : shall be set to 0.
12 - assigned-clocks: main clock from the SoC, for Vybrid <&clks VF610_CLK_NFC>;
13 - assigned-clock-rates: The NAND bus timing is derived from this clock
17 there might be restrictions on maximum rates when using hardware ECC.
19 - #address-cells, #size-cells : Must be present if the device has sub-nodes
27 - compatible: Should be set to "fsl,vf610-nfc-cs".
[all …]
|
| H A D | rockchip,nand-controller.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/rockchip,nand-controller.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - $ref: nand-controller.yaml#
13 - Heiko Stuebner <heiko@sntech.de>
18 - const: rockchip,px30-nfc
19 - const: rockchip,rk2928-nfc
20 - const: rockchip,rv1108-nfc
21 - items:
[all …]
|
| H A D | raw-nand-chip.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/raw-nand-chip.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Miquel Raynal <miquel.raynal@bootlin.com>
13 - $ref: nand-chip.yaml#
16 The ECC strength and ECC step size properties define the user
18 they request the ECC engine to correct {strength} bit errors per
19 {size} bytes for a particular raw NAND chip.
21 The interpretation of these parameters is implementation-defined, so
[all …]
|
| H A D | denali,nand.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Masahiro Yamada <yamada.masahiro@socionext.com>
15 - altr,socfpga-denali-nand
16 - socionext,uniphier-denali-nand-v5a
17 - socionext,uniphier-denali-nand-v5b
19 reg-names:
25 - const: nand_data
26 - const: denali_reg
[all …]
|
| H A D | nand-chip.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/nand-chip.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Miquel Raynal <miquel.raynal@bootlin.com>
13 - $ref: mtd.yaml#
18 SPI-NAND devices are concerned by this description.
23 Contains the chip-select IDs.
25 nand-ecc-engine:
27 A phandle on the hardware ECC engine if any. There are
[all …]
|
| H A D | amlogic,meson-nand.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/amlogic,meson-nand.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - $ref: nand-controller.yaml
13 - liang.yang@amlogic.com
18 - amlogic,meson-gxl-nfc
19 - amlogic,meson-axg-nfc
24 reg-names:
26 - const: nfc
[all …]
|
| H A D | marvell,nand-controller.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/marvell,nand-controlle
[all...] |
| H A D | mediatek,nand-ecc-engine.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/mediatek,nand-ecc-engine.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: MediaTek(MTK) SoCs NAND ECC engine
10 - Xiangsheng Hou <xiangsheng.hou@mediatek.com>
13 MTK NAND ECC engine can cowork with MTK raw NAND and SPI NAND controller.
18 - mediatek,mt2701-ecc
19 - mediatek,mt2712-ecc
20 - mediatek,mt7622-ecc
[all …]
|
| H A D | mxicy,nand-ecc-engine.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/mtd/mxicy,nand-ecc-engine.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Macronix NAND ECC engine
10 - Miquel Raynal <miquel.raynal@bootlin.com>
14 const: mxicy,nand-ecc-engine-rev3
26 - compatible
27 - reg
32 - |
[all …]
|
| H A D | brcm,brcmnand.txt | 3 The Broadcom Set-Top Box NAND controller supports low-level access to raw NAND
4 flash chips. It has a memory-mapped register interface for both control
15 - compatible : May contain an SoC-specific compatibility string (see below)
16 to account for any SoC-specific hardware bits that may be
21 string, like "brcm,brcmnand-v7.0"
23 brcm,brcmnand-v2.1
24 brcm,brcmnand-v2.2
25 brcm,brcmnand-v4.0
26 brcm,brcmnand-v5.0
27 brcm,brcmnand-v6.0
[all …]
|
| H A D | gpmi-nand.txt | 1 * Freescale General-Purpose Media Interface (GPMI)
7 - compatible : should be "fsl,<chip>-gpmi-nand", chip can be:
13 - reg : should contain registers location and length for gpmi and bch.
14 - reg-names: Should contain the reg names "gpmi-nand" and "bch"
15 - interrupts : BCH interrupt number.
16 - interrupt-names : Should be "bch".
17 - dmas: DMA specifier, consisting of a phandle to DMA controller node
19 Refer to dma.txt and fsl-mxs-dma.txt for details.
20 - dma-names: Must be "rx-tx".
21 - clocks : clocks phandle and clock specifier corresponding to each clock
[all …]
|
| H A D | tango-nand.txt | 5 - compatible: "sigma,smp8758-nand"
6 - reg: address/size of nfc_reg, nfc_mem, and pbus_reg
7 - dmas: reference to the DMA channel used by the controller
8 - dma-names: "rxtx"
9 - clocks: reference to the system clock
10 - #address-cells: <1>
11 - #size-cells: <0>
14 See Documentation/devicetree/bindings/mtd/nand-controller.yaml for generic bindings.
18 nandc: nand-controller@2c000 {
19 compatible = "sigma,smp8758-nand";
[all …]
|
| /freebsd/sys/contrib/device-tree/src/arm64/intel/ |
| H A D | socfpga_agilex.dtsi | 1 // SPDX-License-Identifier: GPL-2.0
6 /dts-v1/;
7 #include <dt-bindings/reset/altr,rst-mgr-s10.h>
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/interrupt-controller/arm-gic.h>
10 #include <dt-bindings/clock/agilex-clock.h>
13 compatible = "intel,socfpga-agilex";
14 #address-cells = <2>;
15 #size-cells = <2>;
17 reserved-memory {
[all …]
|
| /freebsd/sys/contrib/device-tree/src/arm64/altera/ |
| H A D | socfpga_stratix10.dtsi | 1 // SPDX-License-Identifier: GPL-2.0-only
6 /dts-v1/;
7 #include <dt-bindings/reset/altr,rst-mgr-s10.h>
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/clock/stratix10-clock.h>
12 compatible = "altr,socfpga-stratix10";
13 #address-cells = <2>;
14 #size-cells = <2>;
16 reserved-memory {
17 #address-cells = <2>;
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/reserved-memory/ |
| H A D | ramoops.txt | 5 recovered after a reboot. This is a child-node of "/reserved-memory", and
10 as kernel log messages, or for optional ECC error-correction data. The total
11 size of these optional buffers must fit in the reserved region.
14 records. These records have a configurable size, with a size of 0 indicating
17 At least one of "record-size", "console-size", "ftrace-size", or "pmsg-size"
18 must be set non-zero, but are otherwise optional as listed below.
23 - compatible: must be "ramoops"
25 - reg: region of memory that is preserved between reboots
30 - ecc-size: enables ECC support and specifies ECC buffer size in bytes
31 (defaults to 0: no ECC)
[all …]
|
| H A D | ramoops.yaml | 1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/reserved-memory/ramoops.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 recovered after a reboot. This is a child-node of "/reserved-memory", and
16 as kernel log messages, or for optional ECC error-correction data. The total
17 size of these optional buffers must fit in the reserved region.
20 records. These records have a configurable size, with a size of 0 indicating
23 At least one of "record-size", "console-size", "ftrace-size", or "pmsg-size"
24 must be set non-zero, but are otherwise optional as listed below.
[all …]
|
| /freebsd/sys/contrib/device-tree/src/arm/intel/socfpga/ |
| H A D | socfpga_arria10.dtsi | 1 // SPDX-License-Identifier: GPL-2.0
6 #include <dt-bindings/interrupt-controller/arm-gic.h>
7 #include <dt-bindings/reset/altr,rst-mgr-a10.h>
10 #address-cell
[all...] |