Home
last modified time | relevance | path

Searched full:driven (Results 1 – 25 of 356) sorted by relevance

12345678910>>...15

/freebsd/sys/contrib/device-tree/Bindings/power/reset/
H A Dgpio-restart.txt7 will be driven in the inactive state. Otherwise its not driven until
11 priority order. The gpio is configured as an output, and driven active,
17 is driven active again. After a delay specified by wait-delay, the
H A Dgpio-restart.yaml17 'open-source' is not found, the GPIO line will be driven in the inactive state. Otherwise its
18 not driven until the restart is initiated.
21 is configured as an output, and driven active, triggering a level triggered reset condition.
25 inactive-delay, the GPIO is driven active again. After a delay specified by wait-delay, the
/freebsd/sys/contrib/device-tree/Bindings/pinctrl/
H A Drenesas,rza1-pinctrl.txt46 "software IO driven" mode to be specified. To do so use the generic
118 enable input bufer for pins requiring software driven IO input
121 enable output buffer for pins requiring software driven IO output
128 internally, while software driven IO direction has to be explicitly
158 Configure TIOC0A as software driven input and TIOC0B as software driven
H A Drenesas,rza1-ports.yaml83 "software IO driven" mode to be specified. To do so use the generic
90 controller driver internally, while software driven IO direction has to
171 * Configure TIOC0A as software driven input
181 * Configure TIOC0B as software driven output
H A Dmarvell,dove-pinctrl.txt64 pmu-nc Pin not driven by any PM function
65 pmu-low Pin driven low (0)
66 pmu-high Pin driven high (1)
/freebsd/sys/contrib/device-tree/Bindings/display/
H A Dtruly,nt35597.txt20 - ports: This device has two video ports driven by two DSIs. Their connections
23 - port@0: DSI input port driven by master DSI
24 - port@1: DSI input port driven by secondary DSI
H A Dssd1307fb.txt11 - solomon,height: Height in pixel of the screen driven by the controller
12 - solomon,width: Width in pixel of the screen driven by the controller
/freebsd/share/man/man4/
H A Dlpt.456 is closed or when the entire buffer is sent in interrupt driven mode.
58 The driver can be configured to be either interrupt-driven, or
61 interrupt-driven can be switched to polled mode by using the
/freebsd/sys/contrib/device-tree/Bindings/mfd/
H A Dst,stm32-timers.yaml11 - advanced-control timers consist of a 16-bit auto-reload counter driven
15 driven by a programmable prescaler and PWM outputs.
16 - basic timers consist of a 16-bit auto-reload counter driven by a
/freebsd/sys/contrib/device-tree/src/arm64/freescale/
H A Dimx8mm-venice-gw72xx-0x-rs422.dts7 * - GPIO4_0 rs485_en needs to be driven high (active)
8 * - GPIO4_2 rs485_hd needs to be driven low (in-active)
H A Dimx8mm-venice-gw72xx-0x-rs422.dtso7 * - GPIO4_0 rs485_en needs to be driven high (active)
8 * - GPIO4_2 rs485_hd needs to be driven low (in-active)
H A Dimx8mm-venice-gw72xx-0x-rs485.dts7 * - GPIO4_0 rs485_en needs to be driven high (active)
8 * - GPIO4_2 rs485_hd needs to be driven high (active)
H A Dimx8mm-venice-gw73xx-0x-rs422.dts7 * - GPIO4_0 rs485_en needs to be driven high (active)
8 * - GPIO4_2 rs485_hd needs to be driven low (in-active)
H A Dimx8mm-venice-gw73xx-0x-rs422.dtso7 * - GPIO4_0 rs485_en needs to be driven high (active)
8 * - GPIO4_2 rs485_hd needs to be driven low (in-active)
H A Dimx8mm-venice-gw73xx-0x-rs485.dts7 * - GPIO4_0 rs485_en needs to be driven high (active)
8 * - GPIO4_2 rs485_hd needs to be driven high (active)
H A Dimx8mm-venice-gw73xx-0x-rs485.dtso7 * - GPIO4_0 rs485_en needs to be driven high (active)
8 * - GPIO4_2 rs485_hd needs to be driven high (active)
H A Dimx8mm-venice-gw72xx-0x-rs485.dtso7 * - GPIO4_0 rs485_en needs to be driven high (active)
8 * - GPIO4_2 rs485_hd needs to be driven high (active)
/freebsd/sys/contrib/device-tree/Bindings/display/panel/
H A Dsharp,lq101r1sx01.txt8 driven by the first link (DSI-LINK1), left or even, is considered the primary
10 to the peripheral driven by the second link (DSI-LINK2, right or odd).
H A Dpanel-dsi-cm.yaml15 are usually driven in command mode. If no backlight is
45 because all its power rails can be driven by the same supply. In that case
H A Dsharp,lq101r1sx01.yaml18 driven by the first link (DSI-LINK1), left or even, is considered the primary
20 to the peripheral driven by the second link (DSI-LINK2, right or odd).
/freebsd/sys/contrib/device-tree/Bindings/input/
H A Dgpio-matrix-keypad.txt1 * GPIO driven matrix keypad device tree bindings
3 GPIO driven matrix keypad is used to interface a SoC with a matrix keypad.
/freebsd/usr.sbin/lptcontrol/
H A Dlptcontrol.825 utility is used to set either the interrupt-driven, extended, standard,
42 Turn on interrupt-driven mode.
/freebsd/sys/contrib/device-tree/Bindings/soc/fsl/cpm_qe/qe/
H A Dpincfg.txt18 0 = The pin is actively driven as an output
20 driven active-low, otherwise it is three-stated.
/freebsd/sys/contrib/device-tree/Bindings/nvmem/
H A Dnvmem.yaml37 The write-protect GPIO is asserted, when it's driven high
39 when it's driven low (logical '0') to allow writing.
/freebsd/share/man/man9/
H A Dmicroseq.994 .It 3 Ta SELECTIN Ta "inverted and driven as parallel port nSelectin signal"
95 .It 2 Ta nINIT Ta "driven as parallel port nInit signal"
96 .It 1 Ta AUTOFEED Ta "inverted and driven as parallel port nAutoFd signal"
97 .It 0 Ta STROBE Ta "inverted and driven as parallel port nStrobe signal"

12345678910>>...15