Home
last modified time | relevance | path

Searched +full:doze +full:- +full:interval +full:- +full:ms (Results 1 – 5 of 5) sorted by relevance

/linux/drivers/input/rmi4/
H A Drmi_f01.c1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (c) 2011-2016 Synaptics Incorporated
87 * When this bit is set, the touch controller employs a noise-filtering
106 * struct f01_device_control - controls basic sensor functions
109 * @doze_interval: controls the interval between checks for finger presence
110 * when the touch sensor is in doze mode, in units of 10ms.
114 * finger lifts before entering the doze state, in units of 100ms.
155 dev_err(&rmi_dev->dev, in rmi_f01_read_properties()
164 props->manufacturer_id = queries[0]; in rmi_f01_read_properties()
166 props->has_lts = queries[1] & RMI_F01_QRY1_HAS_LTS; in rmi_f01_read_properties()
[all …]
/linux/Documentation/devicetree/bindings/input/
H A Dsyna,rmi4.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Jason A. Donenfeld <Jason@zx2c4.com>
11 - Matthias Schiffer <matthias.schiffer@ew.tq-group.com
12 - Vincent Huang <vincent.huang@tw.synaptics.com>
22 - syna,rmi4-i2c
23 - syna,rmi4-spi
28 '#address-cells':
31 '#size-cells':
[all …]
/linux/include/linux/
H A Drmi.h1 /* SPDX-License-Identifier: GPL-2.0-only */
3 * Copyright (c) 2011-2016 Synaptics Incorporated
21 * struct rmi_2d_axis_alignment - target axis alignment
22 * @swap_axes: set to TRUE if desired to swap x- and y-axis
23 * @flip_x: set to TRUE if desired to flip direction on x-axis
24 * @flip_y: set to TRUE if desired to flip direction on y-axis
25 * @clip_x_low - reported X coordinates below this setting will be clipped to
27 * @clip_x_high - reported X coordinates above this setting will be clipped to
29 * @clip_y_low - reported Y coordinates below this setting will be clipped to
31 * @clip_y_high - reported Y coordinates above this setting will be clipped to
[all …]
/linux/include/uapi/linux/
H A Dnl80211.h6 * Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net>
13 * Copyright 2015-2017 Intel Deutschland GmbH
14 * Copyright (C) 2018-2024 Intel Corporation
32 * be careful not to break things - i.e. don't move anything around or so
74 * - a setup station entry is added, not yet authorized, without any rate
76 * - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid
79 * - %NL80211_TDLS_ENABLE_LINK is then used
80 * - after this, the only valid operation is to remove it by tearing down
95 * Frame registration is done on a per-interface basis and registrations
137 * software, like the AP-VLAN type in mac80211 for example, there's
[all …]
/linux/drivers/net/wireless/broadcom/brcm80211/brcmfmac/
H A Dsdio.c1 // SPDX-License-Identifier: ISC
72 __le32 buf; /* Can't be pointer on (64-bit) hosts */
117 #define TXHI (TXQLEN - 256) /* turn on flow control above TXHI */
118 #define TXLOW (TXHI - 256) /* turn off flow control below TXLOW */
146 /* 1: isolate internal sdio signals, put external pads in tri-state; requires
151 /* Force SD->SB reset mapping (rev 11) */
229 #define I_CHIPACTIVE (1 << 29) /* chip from doze to active state */
247 #define SFC_ABORTALL (1 << 3) /* Abort all in-progress frames */
286 * Software-defined protocol header
308 * for HT availability, it could take a couple hundred ms more, so
[all …]