Home
last modified time | relevance | path

Searched full:depending (Results 1 – 25 of 1497) sorted by relevance

12345678910>>...60

/linux/Documentation/hwmon/
H A Dgsc-hwmon.rst21 The voltage inputs are scaled either internally or by the driver depending
33 either internally or by the driver depending on the GSC version and firmware.
44 PWM value will be scaled depending on 6 temperature boundaries.
H A Dnct6775.rst103 PCH, and SMBUS. Depending on the chip type, 2 to 6 of the temperature sources
114 either 1 degC or 0.5 degC, depending on the temperature source and
117 value. Alarms are only supported for temp1 to temp6, depending on the chip type.
251 There are up to seven data points depending on the chip type. Subsequent data
H A Dltc2945.rst56 SENSE+ or VDD pin depending on chip configuration.
84 voltage or ADIN voltage depending on chip configuration.
/linux/drivers/mtd/spi-nor/
H A DKconfig17 Many flash memories support erasing small (4096 B) sectors. Depending
37 Depending on the flash chip this either clears the block protection
54 If the software write protection will be disabled depending on
/linux/Documentation/driver-api/thermal/
H A Dnouveau_thermal.rst41 Some of these thresholds may not be used by Nouveau depending
79 * 2; The fan is driven automatically depending on the temperature.
87 depending on your hardware.
/linux/include/uapi/linux/
H A Dfalloc.h23 * smaller depending on the filesystem and/or the configuration of the
54 * boundaries, but this boundary may be larger or smaller depending on
72 * depending on the filesystem and/or the configuration of the filesystem
/linux/include/linux/
H A Diosys-map.h16 * When accessing a memory region, depending on its location, users may have to
89 * buffer memory. Depending on the location of the memory, the provided helpers
229 * Depending on the state of struct iosys_map.is_iomem, tests if the
246 * Depending on the state of struct iosys_map.is_iomem, tests if the
283 * system memory. Depending on the buffer's location, the helper picks the
303 * system memory. Depending on the mapping location, the helper picks the
320 * Increments the address stored in a iosys mapping. Depending on the
338 * Set value in iosys_map. Depending on the buffer's location, the helper
H A Dpm_runtime.h337 * Invoke the "idle check" callback of @dev and, depending on its return value,
338 * set up autosuspend of @dev or suspend it (depending on whether or not
359 * Set up autosuspend of @dev or suspend it (depending on whether or not
505 * equal to 0, invoke the "idle check" callback of @dev and, depending on its
506 * return value, set up autosuspend of @dev or suspend it (depending on whether
539 * equal to 0, set up autosuspend of @dev or suspend it synchronously (depending
/linux/arch/arm64/boot/dts/qcom/
H A Dmsm8916-samsung-j3-common.dtsi44 /* GPIO pins vary depending on model variant */
48 /* GPIO pins vary depending on model variant */
/linux/Documentation/PCI/endpoint/function/binding/
H A Dpci-test.rst22 msi_interrupts Should be 1 to 32 depending on the number of MSI interrupts
24 msix_interrupts Should be 1 to 2048 depending on the number of MSI-X
/linux/Documentation/ABI/testing/
H A Dsysfs-bus-iio-adc-hi843518 Depending on in_voltageY_sensing_mode the low voltage threshold
37 Depending on in_voltageY_sensing_mode the high voltage threshold
/linux/drivers/staging/media/av7110/
H A DKconfig31 or /lib/firmware (depending on configuration of firmware hotplug).
70 or /lib/firmware (depending on configuration of firmware hotplug).
/linux/Documentation/sound/soc/
H A Dpops-clicks.rst12 depending on the audio usage and this can subsequently cause a small pop or
39 playback in that components are powered in a sequence depending upon stream
H A Ddai.rst30 usually varies depending on the sample rate and the master system clock
53 receive the audio data. Bit clock usually varies depending on sample rate
H A Djack.rst41 These represent a DAPM pin to update depending on some of the status
69 These are all hooked together by the machine driver depending on the
/linux/Documentation/devicetree/bindings/interconnect/
H A Dinterconnect.txt15 depending on the use case. Interconnect providers can also be interconnect
42 multiple paths from different providers depending on use case and the
/linux/Documentation/misc-devices/
H A Dtps6594-pfsm.rst16 manages operational modes. Depending on the current operational mode,
65 Depending on the triggers set, some DDR/GPIO voltage domains can
H A Dapds990x.rst26 might vary quite much depending the spectrum of the light source.
68 to saturate much before that. Real max value varies depending
/linux/arch/arm/include/asm/
H A Dkasan_def.h68 * The KASAN_SHADOW_OFFSET is provided in a Kconfig option depending
71 * the shadow offset depending on this.
/linux/Documentation/netlabel/
H A Dlsm_interface.rst26 low-level packet label depending on the NetLabel build time and run time
43 Depending on the exact configuration, translation between the network packet
/linux/Documentation/sound/hd-audio/
H A Drealtek-pc-beep.rst42 When zero, mix 1Ah (possibly with amplification, depending on L and R bits)
47 When one, mix 1Ah (possibly with amplification, depending on L and R bits)
97 generator and external PCBEEP pin, depending on if the beep generator is
/linux/Documentation/devicetree/bindings/regulator/
H A Dpalmas-pmic.txt35 For ti,palmas-pmic - smps12, smps123, smps3 depending on OTP,
36 smps45, smps457, smps7 depending on variant, smps6, smps[8-9],
/linux/arch/arm/mach-s3c/
H A Dmap-s3c64xx.h19 * These may be used by SROM, NAND or CF depending on settings
57 (depending on SoC POP version) */
/linux/Documentation/userspace-api/media/v4l/
H A Dtuner.rst15 depending on the number of RF connectors on the tuner. The ``type``
47 video outputs, depending on the number of RF connectors on the
/linux/Documentation/driver-api/rapidio/
H A Drapidio.rst55 (depending on number of available mports and networks).
125 Depending on selected enumeration/discovery build configuration, there are
160 routine depending on the configured role of a master port: host or agent.
164 destination ID can be assigned to a master port using various methods depending
220 Depending on RapidIO network size and configuration this automatic

12345678910>>...60