/linux/arch/arm/mach-omap2/ |
H A D | voltage.c | 46 * voltdm_get_voltage() - Gets the current non-auto-compensated voltage 49 * API to get the current non-auto-compensated voltage for a voltage domain. 174 * This API searches only through the non-compensated voltages int the
|
/linux/Documentation/admin-guide/media/ |
H A D | imx.rst | 95 - The VDIC subdev supports motion compensated de-interlacing, with three 199 will carry out motion-compensated de-interlace using "high motion" mode 277 The VDIC carries out motion compensated de-interlacing, with three 384 Motion Compensated De-interlace: 388 support motion-compensated de-interlacing (high motion mode only), 493 Compensated de-interlacing. The adv7180 must output sequential or 551 Compensated de-interlacing. The adv7180 must output sequential or
|
/linux/Documentation/devicetree/bindings/regulator/ |
H A D | renesas,raa215300.yaml | 15 and LPDDR4 memory power requirements. The internally compensated regulators,
|
/linux/Documentation/usb/ |
H A D | mtouchusb.rst | 17 Changed data sent to host from compensated to raw coordinates
|
/linux/include/soc/at91/ |
H A D | at91sam9_sdramc.h | 63 #define AT91_SDRAMC_TCSR (3 << 8) /* Temperature Compensated Self Refresh */
|
H A D | at91sam9_ddrsdr.h | 82 #define AT91_DDRSDRC_TCSR (3 << 8) /* Temperature Compensated Self Refresh */
|
/linux/drivers/iio/pressure/ |
H A D | mpl115.c | 73 /* compensated pressure with 4 fractional bits */ in mpl115_comp_pressure()
|
/linux/include/linux/fsl/ |
H A D | ptp_qoriq.h | 89 #define BYP (1<<3) /* Bypass drift compensated clock */
|
/linux/tools/perf/pmu-events/arch/arm64/thead/yitian710/sys/ |
H A D | ali_drw.json | 311 "BriefDescription": "A Temperature Compensated Refresh(TCR) MRR command to DRAM.",
|
/linux/arch/mips/dec/ |
H A D | int-handler.S | 234 * simple and O(log n), so it gets compensated.
|
/linux/drivers/input/keyboard/ |
H A D | mpr121_touchkey.c | 165 * Capacitance on sensing input varies and needs to be compensated. in mpr121_phys_init()
|
/linux/Documentation/hwmon/ |
H A D | vt1211.rst | 84 external scaling resistors. This external scaling needs to be compensated for
|
/linux/Documentation/driver-api/thermal/ |
H A D | intel_dptf.rst | 214 which is compensated by adjusting Spread spectrum percent. This helps
|
/linux/drivers/iio/magnetometer/ |
H A D | mmc35240.c | 307 * @val: compensated output reading (unit is milli gauss)
|
/linux/arch/m68k/fpsp040/ |
H A D | bindec.S | 74 | compensated for by 'or-ing' in the INEX2 flag to 520 | If INEX is set, round error occurred. This is compensated
|
/linux/drivers/media/i2c/ |
H A D | rdacm21.c | 537 * This should be compensated by increasing the reverse channel in rdacm21_initialize()
|
H A D | rdacm20.c | 555 * This should be compensated by increasing the reverse channel in rdacm20_initialize()
|
/linux/drivers/iio/common/ms_sensors/ |
H A D | ms_sensors_i2c.c | 685 /* Temperature compensated pressure = D1 * SENS - OFF */ in ms_sensors_read_temp_and_pressure()
|
/linux/drivers/net/ethernet/8390/ |
H A D | ne2k-pci.c | 195 * mode results in doubled values, which can be detected and compensated for.
|
/linux/drivers/net/wireless/intel/iwlegacy/ |
H A D | 3945.c | 1345 * current "normal" temperature-compensated Tx power *idx* for in il3945_hw_reg_set_scan_power() 1346 * this rate (1Mb or 6Mb) to yield new temp-compensated scan power in il3945_hw_reg_set_scan_power() 1483 * update base (non-temp-compensated) power idx */ in il3945_hw_reg_set_new_power()
|
/linux/drivers/net/ethernet/intel/ice/ |
H A D | ice_type.h | 343 ICE_CLK_SRC_TCXO = 0, /* Temperature compensated oscillator */
|
/linux/Documentation/virt/kvm/x86/ |
H A D | timekeeping.rst | 431 compensated for properly during normal operation, but when the processor is
|
/linux/include/uapi/linux/ |
H A D | cec.h | 1100 /* Audio Output Compensated Operand (audio_out_compensated) */
|
/linux/drivers/media/tuners/ |
H A D | xc5000.c | 811 dprintk(1, "%s() frequency=%d (compensated to %d)\n", in xc5000_set_digital_params()
|
H A D | xc4000.c | 1198 dprintk(1, "%s() frequency=%d (compensated)\n", in xc4000_set_params()
|