| /freebsd/sys/contrib/device-tree/Bindings/sound/ |
| H A D | nvidia,tegra20-ac97.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/sound/nvidia,tegra20-ac97.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Thierry Reding <treding@nvidia.com>
11 - Jon Hunter <jonathanh@nvidia.com>
15 const: nvidia,tegra20-ac97
23 reset-names:
35 dma-names:
37 - const: rx
[all …]
|
| H A D | infineon,peb2466.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Infineon PEB2466 codec
10 - Herve Codina <herve.codina@bootlin.com>
13 The Infineon PEB2466 codec is a programmable DSP-based four channels codec
16 The time-slots used by the codec must be set and so, the properties
17 'dai-tdm-slot-num', 'dai-tdm-slot-width', 'dai-tdm-slot-tx-mask' and
18 'dai-tdm-slot-rx-mask' must be present in the sound card node for sub-nodes
19 that involve the codec. The codec uses one 8bit time-slot per channel.
[all …]
|
| H A D | ti,tlv320aic3x.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: Texas Instruments TLV320AIC3x Codec
11 TLV320AIC3x are a series of low-power stereo audio codecs with stereo
13 single-ended or fully differential configurations.
16 data bus is programmable for I2S, left/right-justified, DSP, or TDM modes.
20 CODEC output pins:
29 CODEC input pins for TLV320AIC3104:
35 CODEC input pins for other compatible codecs:
[all …]
|
| H A D | qcom,wcd9335.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Qualcomm WCD9335 Audio Codec
10 - Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
13 Qualcomm WCD9335 Codec is a standalone Hi-Fi audio codec IC with in-built
27 clock-names:
29 - const: mclk
30 - const: slimbus
35 interrupt-names:
[all …]
|
| H A D | tlv320aic3x.txt | 1 Texas Instruments - tlv320aic3x Codec module
7 - compatible - "string" - One of:
8 "ti,tlv320aic3x" - Generic TLV320AIC3x device
9 "ti,tlv320aic33" - TLV320AIC33
10 "ti,tlv320aic3007" - TLV320AIC3007
11 "ti,tlv320aic3106" - TLV320AIC3106
12 "ti,tlv320aic3104" - TLV320AIC3104
15 - reg - <int> - I2C slave address
20 - reset-gpios - GPIO specification for the active low RESET input.
21 - ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality
[all …]
|
| H A D | rt5659.txt | 1 RT5659/RT5658 audio CODEC
7 - compatible : One of "realtek,rt5659" or "realtek,rt5658".
9 - reg : The I2C address of the device.
11 - interrupts : The CODEC's interrupt output.
15 - clocks: The phandle of the master clock to the CODEC
16 - clock-names: Should be "mclk"
18 - realtek,in1-differential
19 - realtek,in3-differential
20 - realtek,in4-differential
21 Boolean. Indicate MIC1/3/4 input are differential, rather than single-ended.
[all …]
|
| H A D | rohm,bd28623.txt | 3 This codec does not have any control buses such as I2C, it detect format and
5 to GPIOs: reset and mute.
8 - compatible : should be "rohm,bd28623"
9 - #sound-dai-cells: should be 0.
10 - VCCA-supply : regulator phandle for the VCCA supply
11 - VCCP1-supply : regulator phandle for the VCCP1 supply
12 - VCCP2-supply : regulator phandle for the VCCP2 supply
15 - reset-gpios : GPIO specifier for the active low reset line
16 - mute-gpios : GPIO specifier for the active low mute line
20 codec {
[all …]
|
| H A D | cirrus,cs4271.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Cirrus Logic CS4271 audio CODEC
10 - Alexander Sverdlin <alexander.sverdlin@gmail.com>
11 - Nikita Shubin <nikita.shubin@maquefel.me>
14 The CS4271 is a stereo audio codec. This device supports both the I2C
18 - $ref: dai-common.yaml#
19 - $ref: /schemas/spi/spi-peripheral-props.yaml#
28 spi-cpha: true
[all …]
|
| H A D | st,sta32x.txt | 1 STA32X audio CODEC
7 - compatible: "st,sta32x"
8 - reg: the I2C address of the device for I2C
9 - reset-gpios: a GPIO spec for the reset pin. If specified, it will be
10 deasserted before communication to the codec starts.
12 - power-down-gpios: a GPIO spec for the power down pin. If specified,
13 it will be deasserted before communication to the codec
16 - Vdda-supply: regulator spec, providing 3.3V
17 - Vdd3-supply: regulator spec, providing 3.3V
18 - Vcc-supply: regulator spec, providing 5V - 26V
[all …]
|
| H A D | tas27xx.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2 # Copyright (C) 2020-2022 Texas Instruments Incorporated
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Shenghao Ding <shenghao-ding@ti.com>
14 The TAS2764/TAS2780 is a mono, digital input Class-D audio amplifier
20 - $ref: dai-common.yaml#
25 - ti,tas2764
26 - ti,tas2780
33 reset-gpios:
[all …]
|
| H A D | ti,tas27xx.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2 # Copyright (C) 2020-2022 Texas Instruments Incorporated
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Shenghao Ding <shenghao-ding@ti.com>
14 The TAS2764/TAS2780 is a mono, digital input Class-D audio amplifier
20 - $ref: dai-common.yaml#
25 - ti,tas2764
26 - ti,tas2780
33 reset-gpios:
[all …]
|
| H A D | rohm,bd28623.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 This codec does not have any control buses such as I2C, it detect
12 that can be connected to GPIOs reset and mute.
15 - Katsuhiro Suzuki <katsuhiro@katsuster.net>
18 - $ref: dai-common.yaml#
24 "#sound-dai-cells":
27 VCCA-supply:
31 VCCP1-supply:
[all …]
|
| H A D | tas571x.txt | 3 The codec is controlled through an I2C interface. It also has two other
4 signals that can be wired up to GPIOs: reset (strongly recommended), and
9 - compatible: should be one of the following:
10 - "ti,tas5707"
11 - "ti,tas5711",
12 - "ti,tas5717",
13 - "ti,tas5719",
14 - "ti,tas5721"
15 - "ti,tas5733"
16 - reg: The I2C address of the device
[all …]
|
| H A D | tlv320aic31xx.txt | 1 Texas Instruments - tlv320aic31xx Codec module
7 - compatible - "string" - One of:
8 "ti,tlv320aic310x" - Generic TLV320AIC31xx with mono speaker amp
9 "ti,tlv320aic311x" - Generic TLV320AIC31xx with stereo speaker amp
10 "ti,tlv320aic3100" - TLV320AIC3100 (mono speaker amp, no MiniDSP)
11 "ti,tlv320aic3110" - TLV320AIC3110 (stereo speaker amp, no MiniDSP)
12 "ti,tlv320aic3120" - TLV320AIC3120 (mono speaker amp, MiniDSP)
13 "ti,tlv320aic3111" - TLV320AIC3111 (stereo speaker amp, MiniDSP)
14 "ti,tlv320dac3100" - TLV320DAC3100 (no ADC, mono speaker amp, no MiniDSP)
15 "ti,tlv320dac3101" - TLV320DAC3101 (no ADC, stereo speaker amp, no MiniDSP)
[all …]
|
| H A D | qcom,wcd934x.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Qualcomm WCD9340/WCD9341 Audio Codec
10 - Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
13 Qualcomm WCD9340/WCD9341 Codec is a standalone Hi-Fi audio codec IC.
14 It has in-built Soundwire controller, pin controller, interrupt mux and
27 reset-gpios:
28 description: GPIO spec for reset line to use
31 slim-ifc-dev:
[all …]
|
| H A D | cs4349.txt | 1 CS4349 audio CODEC
5 - compatible : "cirrus,cs4349"
7 - reg : the I2C address of the device for I2C
11 - reset-gpios : a GPIO spec for the reset pin.
15 codec: cs4349@48 {
18 reset-gpios = <&gpio 54 0>;
|
| H A D | ti,pcm3168a.txt | 3 This driver supports both SPI and I2C bus access for this codec
7 - compatible: "ti,pcm3168a"
9 - clocks : Contains an entry for each entry in clock-names
11 - clock-names : Includes the following entries:
14 - VDD1-supply : Digital power supply regulator 1 (+3.3V)
16 - VDD2-supply : Digital power supply regulator 2 (+3.3V)
18 - VCCAD1-supply : ADC power supply regulator 1 (+5V)
20 - VCCAD2-supply : ADC power supply regulator 2 (+5V)
22 - VCCDA1-supply : DAC power supply regulator 1 (+5V)
24 - VCCDA2-supply : DAC power supply regulator 2 (+5V)
[all …]
|
| H A D | cs35l32.txt | 1 CS35L32 audio CODEC
5 - compatible : "cirrus,cs35l32"
7 - reg : the I2C address of the device for I2C. Address is determined by the level
10 - VA-supply, VP-supply : power supplies for the device,
15 - reset-gpios : a GPIO spec for the reset pin. If specified, it will be
16 deasserted before communication to the codec starts.
18 - cirrus,boost-manager : Boost voltage control.
19 0 = Automatically managed. Boost-converter output voltage is the higher
21 1 = Automatically managed irrespective of audio, adapting for low-power
22 dissipation when LEDs are ON, and operating in Fixed-Boost Bypass Mode
[all …]
|
| H A D | ti,tlv320dac3100.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Texas Instruments - tlv320aic31xx Codec module
10 - Shenghao Ding <shenghao-ding@ti.com>
13 CODEC output pins:
21 CODEC input pins:
28 The pins can be used in referring sound node's audio-routing property.
33 - ti,tlv320aic310x # - Generic TLV320AIC31xx with mono speaker amp
34 - ti,tlv320aic311x # - Generic TLV320AIC31xx with stereo speaker amp
[all …]
|
| H A D | pcm1789.txt | 3 PCM1789 is a simple audio codec that can be connected via
8 - compatible: "ti,pcm1789"
12 - reg: the I2C address
13 - reset-gpios: GPIO to control the RESET pin
17 audio-codec@4c {
20 reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
21 #sound-dai-cells = <0>;
|
| H A D | cs53l30.txt | 1 CS53L30 audio CODEC
5 - compatible : "cirrus,cs53l30"
7 - reg : the I2C address of the device
9 - VA-supply, VP-supply : power supplies for the device,
14 - reset-gpios
[all...] |
| H A D | tas2764.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
6 $schema: "http://devicetree.org/meta-schemas/core.yaml#"
11 - Dan Murphy <dmurphy@ti.com>
14 The TAS2764 is a mono, digital input Class-D audio amplifier optimized for
22 - ti,tas2764
29 reset-gpios:
31 description: GPIO used to reset the device.
33 shutdown-gpios:
40 ti,imon-slot-no:
[all …]
|
| /freebsd/sys/contrib/device-tree/src/arm64/amlogic/ |
| H A D | meson-gxbb-kii-pro.dts | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
8 #include "meson-gxbb-p20x.dtsi"
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/leds/common.h>
12 #include <dt-bindings/sound/meson-aiu.h>
15 compatible = "videostrong,kii-pro", "amlogic,meson-gxbb";
18 spdif_dit: audio-codec-0 {
19 #sound-dai-cells = <0>;
[all …]
|
| H A D | meson-axg-s400.dts | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
8 #include "meson-axg.dtsi"
9 #include <dt-bindings/input/input.h>
12 compatible = "amlogic,s400", "amlogic,a113d", "amlogic,meson-axg";
16 compatible = "adc-keys";
17 io-channels = <&saradc 0>;
18 io-channel-names = "buttons";
19 keyup-threshold-microvolt = <1800000>;
21 button-next {
[all …]
|
| H A D | meson-gxm-rbox-pro.dts | 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 * Copyright (c) 2016-2017 Andreas Färber
5 * Based on nexbox-a1:
14 /dts-v1/;
16 #include "meson-gxm.dtsi"
17 #include <dt-bindings/sound/meson-aiu.h>
20 compatible = "kingnovel,r-box-pro", "amlogic,s912", "amlogic,meson-gxm";
21 model = "R-Box Pro";
29 stdout-path = "serial0:115200n8";
37 spdif_dit: audio-codec-0 {
[all …]
|