Searched full:bucks (Results 1 – 25 of 27) sorted by relevance
12
/freebsd/sys/contrib/device-tree/Bindings/regulator/ |
H A D | rohm,bd71815-regulator.yaml | 57 comments below for bucks/LDOs which support this. 0 means 77 comments below for bucks/LDOs which support this. 0 means 86 comments below for bucks/LDOs which support this. 0 means 92 # Bucks 1 and 2 support giving separate voltages for operational states 95 # state changes. Omitting these properties from bucks 1 and 2 leave 99 # Bucks 3-5 and ldos 1-5 support setting the RUN state voltage here. 109 # that setting non zero voltages for bucks 1/2 will also enable voltage
|
H A D | rohm,bd71828-regulator.yaml | 54 bucks which support this. 0 means disabled. 62 bucks which support this. 0 means disabled. 70 bucks which support this. 0 means disabled. 78 bucks which support this. 0 means disabled.
|
H A D | samsung,s2mpa01.yaml | 33 # 10 bucks 51 Note: Some bucks share the ramp rate setting i.e. same ramp value 52 will be set for a particular group of bucks so provide the same
|
H A D | rohm,bd71847-regulator.yaml | 62 bucks which support this. 0 means disabled. 70 bucks which support this. 0 means disabled. 78 bucks which support this. 0 means disabled.
|
H A D | samsung,s2mpa01.txt | 34 Note: Some bucks share the ramp rate setting i.e. same ramp value 35 will be set for a particular group of bucks so provide the same
|
H A D | maxim,max77802.yaml | 31 regulators are:: bucks 2-4 and LDOs 1-35. Also, it only takes effect if the 64 bucks supporting the regulator-mode property (changing mode to Low Power
|
H A D | rohm,bd71837-regulator.yaml | 63 bucks which support this. 0 means disabled. 71 bucks which support this. 0 means disabled. 79 bucks which support this. 0 means disabled.
|
H A D | samsung,s2mps11.txt | 43 Note: On S2MPS11 some bucks share the ramp rate setting i.e. same ramp value 44 will be set for a particular group of bucks so provide the same
|
H A D | max77802.txt | 47 -BUCKn : for BUCKs, where n can lie in range 1 to 10. 68 are: BUCKs 2-4 and LDOs 1-35. Also, it only takes effect if the regulator has
|
H A D | max8997-regulator.txt | 45 multiple bucks, changing the voltage value of one of the bucks may affect
|
H A D | maxim,max8997.yaml | 104 When GPIO-DVS mode is used for multiple bucks, changing the voltage value 105 of one of the bucks may affect that of another buck, which is the side 134 # 7 bucks
|
H A D | samsung,s2mps11.yaml | 33 # 10 bucks
|
H A D | samsung,s2mps13.yaml | 33 # 10 bucks
|
H A D | samsung,s2mps15.yaml | 33 # 10 bucks
|
H A D | samsung,s2mpu02.yaml | 33 # 7 bucks
|
H A D | samsung,s2mps14.yaml | 50 # 5 bucks
|
H A D | mt6315-regulator.yaml | 14 that contains 4 BUCKs output which can combine with each other
|
H A D | maxim,max77686.yaml | 54 # 9 bucks
|
H A D | max77686.txt | 26 -BUCKn : for BUCKs, where n can lie in range 1 to 9.
|
H A D | samsung,s5m8767.yaml | 46 # 8 bucks
|
H A D | richtek,rtq2208.yaml | 16 Bucks support "regulator-allowed-modes" and "regulator-mode". The former defines the permitted
|
/freebsd/sys/contrib/device-tree/Bindings/mfd/ |
H A D | da9062.txt | 11 da9062-regulator : : LDOs & BUCKs 22 da9062-regulator : : LDOs & BUCKs 54 - regulators : This node defines the settings for the LDOs and BUCKs.
|
H A D | da9063.txt | 7 da9063-regulator : : LDOs & BUCKs 24 - regulators : This node defines the settings for the LDOs and BUCKs.
|
H A D | mediatek,mt6357.yaml | 63 List of MT6357 BUCKs and LDOs regulators.
|
/freebsd/sys/contrib/device-tree/Bindings/usb/ |
H A D | mediatek,mt6360-tcpc.yaml | 14 regulators (BUCKs/LDOs), and TypeC Port Switch with Power Delivery controller.
|
12