Home
last modified time | relevance | path

Searched +full:attn +full:- +full:gpios (Results 1 – 5 of 5) sorted by relevance

/linux/Documentation/devicetree/bindings/input/touchscreen/
H A Dsis_i2c.txt4 - compatible: must be "sis,9200-ts"
5 - reg: i2c slave address
6 - interrupts: touch controller interrupt (see interrupt
10 - pinctrl-names: should be "default" (see pinctrl binding [1]).
11 - pinctrl-0: a phandle pointing to the pin settings for the
13 - attn-gpios: the gpio pin used as attention line
14 - reset-gpios: the gpio pin used to reset the controller
15 - wakeup-source: touchscreen can be used as a wakeup source
17 [0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
18 [1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
[all …]
/linux/Documentation/devicetree/bindings/sound/
H A Dcs35l36.txt5 - compatible : "cirrus,cs35l36"
7 - reg : the I2C address of the device for I2C
9 - VA-supply, VP-supply : power supplies for the device,
13 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
18 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
24 - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
32 - cirrus,multi-amp-mode : Boolean to determine if there are more than
33 one amplifier in the system. If more than one it is best to Hi-Z the ASP
36 - cirrus,boost-ctl-select : Boost converter control source selection.
39 0x00 - Control Port Value
[all …]
/linux/arch/arm/boot/dts/intel/pxa/
H A Dpxa300-raumfeld-controller.dts1 // SPDX-License-Identifier: GPL-2.0
3 /dts-v1/;
5 #include "pxa300-raumfeld-common.dtsi"
9 compatible = "raumfeld,raumfeld-controller-pxa303", "marvell,pxa300";
11 reg_vbatt: regulator-vbatt {
12 compatible = "regulator-fixed";
13 regulator-name = "vbatt-fixed-supply";
14 regulator-min-microvolt = <3700000>;
15 regulator-max-microvolt = <3700000>;
16 regulator-always-on;
[all …]
/linux/drivers/atm/
H A Dsolos-pci.c1 // SPDX-License-Identifier: GPL-2.0-only
4 * Traverse Technologies -- https://www.traverse.com.au/
5 * Xrio Limited -- http://www.xrio.com/
38 #define PTAG "solos-pci"
67 #define RX_BUF(card, nr) ((card->buffers) + (nr)*(card->buffer_size)*2)
68 #define TX_BUF(card, nr) ((card->buffers) + (nr)*(card->buffer_size)*2 + (card->buffer_size))
69 #define FLASH_BUF ((card->buffers) + 4*(card->buffer_size)*2)
97 #define SKB_CB(skb) ((struct solos_skb_cb *)skb->cb)
140 #define SOLOS_CHAN(atmdev) ((int)(unsigned long)(atmdev)->phy_data)
146 MODULE_FIRMWARE("solos-FPGA.bin");
[all …]
/linux/include/linux/
H A Drmi.h1 /* SPDX-License-Identifier: GPL-2.0-only */
3 * Copyright (c) 2011-2016 Synaptics Incorporated
21 * struct rmi_2d_axis_alignment - target axis alignment
22 * @swap_axes: set to TRUE if desired to swap x- and y-axis
23 * @flip_x: set to TRUE if desired to flip direction on x-axis
24 * @flip_y: set to TRUE if desired to flip direction on y-axis
25 * @clip_x_low - reported X coordinates below this setting will be clipped to
27 * @clip_x_high - reported X coordinates above this setting will be clipped to
29 * @clip_y_low - reported Y coordinates below this setting will be clipped to
31 * @clip_y_high - reported Y coordinates above this setting will be clipped to
[all …]