| /linux/drivers/pinctrl/aspeed/ |
| H A D | pinctrl-aspeed-g4.c | 771 #define U5 95 macro
773 SIG_EXPR_LIST_DECL_SINGLE(U5, VPIB1, VPI30, VPI30_DESC, U5_DESC);
774 SIG_EXPR_LIST_DECL_SINGLE(U5, RXD1, RXD1, U5_DESC);
775 PIN_DECL_2(U5, GPIOL7, VPIB1, RXD1);
776 FUNC_GROUP_DECL(RXD1, U5);
1037 FUNC_GROUP_DECL(VPI30, T5, U3, V1, U4, V2, W1, U5, V3, W2, Y1, V4, W3, Y2, AA1,
2099 ASPEED_PINCTRL_PIN(U5),
2460 ASPEED_SB_PINCONF(PIN_CONFIG_BIAS_PULL_DOWN, U1, U5, SCU8C, 26),
2461 ASPEED_SB_PINCONF(PIN_CONFIG_BIAS_DISABLE, U1, U5, SCU8C, 26),
|
| H A D | pinctrl-aspeed-g5.c | 869 #define U5 112 macro
870 SIG_EXPR_LIST_DECL_SINGLE(U5, VPIG8, VPI24, VPI24_DESC, SIG_DESC_SET(SCU88, 8),
872 PIN_DECL_1(U5, GPIOO0, VPIG8);
930 U3, W3, AA3, Y3, T4, U5, U4, AB3, Y4, AA4, W4, V4, W5, AA5,
2104 ASPEED_PINCTRL_PIN(U5),
2539 ASPEED_SB_PINCONF(PIN_CONFIG_BIAS_PULL_DOWN, U5, W4, SCU8C, 30),
2540 ASPEED_SB_PINCONF(PIN_CONFIG_BIAS_DISABLE, U5, W4, SCU8C, 30),
|
| H A D | pinmux-aspeed.h | 107 * W1 and U5:
111 * U5 GPIOL7 VPIB1 SCU90[5:4]=3 & SCU84[23]=1 RXD1 SCU84[23]=1 GPIOL7
|
| /linux/drivers/atm/ |
| H A D | Kconfig | 48 The driver works with MMF (-MF or ...F) and UTP-5 (-U5 or ...D)
|
| /linux/arch/sh/boards/ |
| H A D | board-magicpanelr2.c | 199 /* U7 (x); U6 (x); U5 (x); U4 GPI+(/AC_FAULT); in setup_port_multiplexing()
|
| /linux/arch/arm/boot/dts/ti/omap/ |
| H A D | am335x-boneblue.dts | 538 "SVO1", /* U5 */
|
| /linux/drivers/irqchip/ |
| H A D | irq-sifive-plic.c | 26 * specified in chapter 8 of the SiFive U5 Coreplex Series Manual:
|
| /linux/drivers/gpu/drm/amd/display/dc/dml2/ |
| H A D | dml_display_rq_dlg_calc.c | 231 dml_float_t max_dst_y_per_vm_vblank = 32.0; //U5.2 in dml_rq_dlg_get_dlg_reg()
|
| /linux/drivers/pinctrl/ |
| H A D | pinctrl-ep93xx.c | 656 PINCTRL_PIN(259, "P[1]"), /* U5 */
1027 PINCTRL_PIN(276, "P[6]"), /* U5 */
|
| /linux/drivers/net/wireless/intersil/p54/ |
| H A D | p54usb.c | 94 {USB_DEVICE(0x0baf, 0x0118)}, /* U.S. Robotics U5 802.11g Adapter*/
|
| /linux/drivers/pinctrl/mediatek/ |
| H A D | pinctrl-mtk-mt8127.h | 803 "U5", "mt8127",
|
| /linux/drivers/net/ieee802154/ |
| H A D | mrf24j40.c | 1146 /* Set GPIO3 HIGH to enable U5 voltage regulator */ in mrf24j40_hw_init()
|
| /linux/drivers/media/pci/bt8xx/ |
| H A D | bttv-cards.c | 1082 GPIO20: U5.A1 (second hef4052bt)
1085 GPIO23: A5,A0, U5,nEN
1436 GPIO3: U4.nEN, U5.A0, A5.nEN
4556 * xxx0 is pin xxx of multiplexer U5,
|
| /linux/drivers/scsi/bnx2i/ |
| H A D | bnx2i_hwi.c | 2272 additional_notice = "ERL0, U5"; in bnx2i_process_iscsi_error()
|