| /linux/drivers/clk/sunxi/ |
| H A D | Kconfig | 25 usually needed for the PMIC communication, mostly.
33 mostly.
40 usually needed for the PMIC communication, mostly.
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-ata | 111 Mostly used by PATA devices.
113 xfer_mode: (RO) Current transfer mode. Mostly used by
117 Mostly used by PATA devices.
|
| /linux/drivers/hid/usbhid/ |
| H A D | Kconfig | 58 This is almost certainly not what you want. This is mostly
74 This is almost certainly not what you want. This is mostly
|
| /linux/include/net/libeth/ |
| H A D | cache.h | 41 * @...: from 1 to 3 CL group sizes (read-mostly, read-write, cold)
54 * @ro: expected size of the read-mostly group
|
| /linux/include/trace/events/ |
| H A D | regulator.h | 106 * Events that take a range of numerical values, mostly for voltages
141 * Events that take a single value, mostly for readback and refcounts.
|
| /linux/tools/testing/selftests/kvm/include/ |
| H A D | sparsebit.h | 11 * long as bits that are mostly set or mostly cleared are close
|
| /linux/include/linux/ |
| H A D | elfcore.h | 26 * These mostly have the same names as the SVR4 types with "elf_"
28 * and the typedef forms have been avoided. This is mostly like
|
| H A D | iversion.h | 10 * The change attribute (i_version) is mandated by NFSv4 and is mostly for
121 * flagged or converted in any way. This is mostly used to access a self-managed
229 * mostly treats it as opaque, but in the case where it holds a write
|
| /linux/Documentation/i2c/ |
| H A D | summary.rst | 18 SMBus (System Management Bus) is based on the I2C protocol, and is mostly
25 Because the SMBus is mostly a subset of the generalized I2C bus, we can
|
| /linux/arch/arm/mach-bcm/ |
| H A D | Kconfig | 77 This is a network SoC line mostly used in home routers and
176 This SoC line is mostly used in home routers and is some cheaper
|
| /linux/Documentation/devicetree/bindings/bus/ |
| H A D | ti-sysc.yaml | 16 is mostly used for interaction between module and Power, Reset and Clock
18 than that it is mostly independent of the interconnect.
|
| /linux/fs/xfs/ |
| H A D | xfs_mount.h | 145 * The struct xfsmount layout is optimised to separate read-mostly variables
146 * from variables that are frequently modified. We put the read-mostly variables
149 * Typically, read-mostly variables are those that are set at mount time and
257 * End of read-mostly variables. Frequently written variables and locks
260 * the read-mostly variables.
720 * Same as above, but does return negative values. Mostly useful for
|
| /linux/arch/powerpc/platforms/86xx/ |
| H A D | mpc86xx.h | 11 * mpc86xx_* files. Mostly for use by mpc86xx_setup().
|
| /linux/net/nfc/hci/ |
| H A D | Kconfig | 8 implementation. This is mostly needed for devices that only process
|
| /linux/arch/x86/boot/ |
| H A D | mtools.conf.in | 13 # 2.88 MB floppy disk image (mostly for virtual uses)
|
| /linux/drivers/gpu/drm/nouveau/include/nvkm/subdev/bios/ |
| H A D | i2c.h | 10 /* made up - mostly */
|
| /linux/net/lapb/ |
| H A D | Kconfig | 12 it is used to transport higher level protocols (mostly X.25 Packet
|
| /linux/fs/smb/common/smbdirect/ |
| H A D | smbdirect.h | 18 * Connection parameters mostly from [MS-SMBD] 3.1.1.1
|
| /linux/drivers/memory/ |
| H A D | Kconfig | 10 useful mostly on embedded systems. These could be controllers
118 Enables verbose debugging mostly to decode the bootloader provided
|
| /linux/drivers/clk/keystone/ |
| H A D | Kconfig | 26 This is mostly only useful for debugging purposes, and will
|
| /linux/arch/powerpc/platforms/powermac/ |
| H A D | pmac.h | 12 * pmac_* files. Mostly for use by pmac_setup
|
| /linux/include/net/ |
| H A D | hotdata.h | 15 /* Read mostly data used in network fast paths. */
|
| /linux/fs/ufs/ |
| H A D | file.c | 33 * We have mostly NULL's here: the current defaults are ok for
|
| /linux/Documentation/devicetree/bindings/serial/ |
| H A D | qcom,msm-uart.yaml | 15 dma-engine isn't needed. From a software perspective it's mostly compatible
|
| /linux/fs/minix/ |
| H A D | file.c | 13 * We have mostly NULLs here: the current defaults are OK for
|