| /linux/Documentation/devicetree/bindings/net/can/ |
| H A D | fsl,flexcan.yaml | 4 $id: http://devicetree.org/schemas/net/can/fsl,flexcan.yaml#
8 Flexcan CAN controller on Freescale's ARM and PowerPC system-on-a-chip (SOC).
17 - fsl,imx95-flexcan
18 - fsl,imx93-flexcan
19 - fsl,imx8qm-flexcan
20 - fsl,imx8mp-flexcan
21 - fsl,imx6q-flexcan
22 - fsl,imx28-flexcan
23 - fsl,imx25-flexcan
24 - fsl,p1010-flexcan
[all …]
|
| /linux/drivers/net/can/flexcan/ |
| H A D | Makefile | 3 obj-$(CONFIG_CAN_FLEXCAN) += flexcan.o
5 flexcan-objs :=
6 flexcan-objs += flexcan-core.o
7 flexcan-objs += flexcan-ethtool.o
|
| H A D | flexcan.h | 2 * flexcan.c - FLEXCAN CAN controller driver
19 /* FLEXCAN hardware feature flags
|
| H A D | flexcan-ethtool.c | 13 #include "flexcan.h"
|
| /linux/Documentation/networking/device_drivers/can/freescale/ |
| H A D | flexcan.rst | 4 Flexcan CAN Controller driver
13 For most flexcan IP cores the driver supports 2 RX modes:
18 The older flexcan cores (integrated into the i.MX25, i.MX28, i.MX35
27 As reception of RTR frames is part of the CAN standard, all flexcan
|
| /linux/drivers/clk/mxs/ |
| H A D | clk-imx28.c | 39 #define FLEXCAN (CLKCTRL + 0x0160) macro
225 clks[can0] = mxs_clk_gate("can0", "ref_xtal", FLEXCAN, 30); in mx28_clocks_init()
226 clks[can1] = mxs_clk_gate("can1", "ref_xtal", FLEXCAN, 28); in mx28_clocks_init()
|
| /linux/arch/powerpc/boot/dts/fsl/ |
| H A D | p1010si-post.dtsi | 145 compatible = "fsl,p1010-flexcan";
152 compatible = "fsl,p1010-flexcan";
|
| /linux/drivers/net/can/ |
| H A D | Makefile | 25 obj-$(CONFIG_CAN_FLEXCAN) += flexcan/
|
| H A D | Kconfig | 145 tristate "Support for Freescale FLEXCAN based chips"
150 Say Y here if you want to support for Freescale FlexCAN.
|
| /linux/arch/arm64/boot/dts/freescale/ |
| H A D | s32g2.dtsi | 421 compatible = "nxp,s32g2-flexcan";
434 compatible = "nxp,s32g2-flexcan";
626 compatible = "nxp,s32g2-flexcan";
639 compatible = "nxp,s32g2-flexcan";
|
| H A D | imx8-ss-dma.dtsi | 400 compatible = "fsl,imx8qm-flexcan";
417 compatible = "fsl,imx8qm-flexcan";
438 compatible = "fsl,imx8qm-flexcan";
|
| /linux/arch/arm/boot/dts/nxp/imx/ |
| H A D | imx6qdl-tx6.dtsi | 345 /* PAD DISP0_DAT0 is used for the Flexcan transceiver control */
475 pinctrl_flexcan_xcvr: flexcan-xcvrgrp {
477 MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x1b0b0 /* Flexcan XCVR enable */
|
| H A D | imx53.dtsi | 572 compatible = "fsl,imx53-flexcan", "fsl,imx25-flexcan";
582 compatible = "fsl,imx53-flexcan", "fsl,imx25-flexcan";
|
| H A D | imx6ul-tx6ul.dtsi | 563 /* PAD DISP0_DAT0 is used for the Flexcan transceiver control on STK5-v5 */
718 pinctrl_flexcan_xcvr: flexcan-xcvrgrp {
720 MX6UL_PAD_LCD_DATA00__GPIO3_IO05 0x0b0b0 /* Flexcan XCVR enable */
|
| H A D | imx53-tx53.dtsi | 295 fsl,pins = <MX53_PAD_DISP0_DAT0__GPIO4_21 0xe0>; /* Flexcan XCVR enable */
|
| H A D | imx6qdl-nitrogen6x.dtsi | 374 /* Flexcan XCVR enable */
|
| H A D | imx6qdl-nitrogen6_som2.dtsi | 362 /* Flexcan XCVR enable */
|
| H A D | imx6qdl-sabrelite.dtsi | 420 /* Flexcan XCVR enable */
|
| H A D | imx6qdl-nitrogen6_max.dtsi | 435 /* Flexcan XCVR enable */
|
| /linux/arch/m68k/include/asm/ |
| H A D | m5441xsim.h | 324 * Flexcan module
|
| /linux/arch/arm/boot/dts/nxp/mxs/ |
| H A D | imx28.dtsi | 1052 compatible = "fsl,imx28-flexcan";
1061 compatible = "fsl,imx28-flexcan";
|