Searched full:detectors (Results 1 – 20 of 20) sorted by relevance
155 * @detectors: array of dynamically created detector elements for this freq157 * Channel detectors are required to provide multi-channel DFS detection, e.g.164 struct pri_detector *detectors[]; member175 cd->detectors[i]->reset(cd->detectors[i], dpd->last_pulse_ts); in channel_detector_reset()188 struct pri_detector *de = cd->detectors[i]; in channel_detector_exit()202 cd = kzalloc(struct_size(cd, detectors, dpd->num_radar_types), GFP_ATOMIC); in channel_detector_create()214 cd->detectors[i] = de; in channel_detector_create()251 /* dpd_reset(): reset all channel detectors */292 struct pri_detector *pd = cd->detectors[i]; in dpd_add_pulse()330 /* delete all channel detectors for previous DFS domain */ in dpd_set_domain()
67 * The run state of the lockup detectors is controlled by the content of the76 * detectors are 'suspended' while 'watchdog_thresh' is equal zero.
21 the common infrastructure for handling hardlockup detectors. It is
13 The FSA880 and FSA9480 are USB port accessory detectors and switches.
45 * softlockup or RCU stall detectors, and when the system is kicked in test_body()
13 RTDs (Resistance Temperature Detectors) are a kind of temperature sensors
13 1. Bus clash or parity errors: This mechanism relies on low-level detectors
36 The soft and hard lockup detectors are built on top of the hrtimer and
4217 To disable both hard and soft lockup detectors,4482 nowatchdog [KNL] Disable both lockup detectors, i.e.8190 disables both lockup detectors. Default is 10
986 /* disable detectors to reset them */ in tegra_usb_phy_configure_pmc()995 /* enable detectors */ in tegra_usb_phy_configure_pmc()1002 /* detectors starts to work after 10ms */ in tegra_usb_phy_configure_pmc()
1389 /* power down the line state detectors of the pad */ in tegra210_pmc_utmi_enable_phy_sleepwalk()1474 /* power up the line state detectors of the pad */ in tegra210_pmc_utmi_enable_phy_sleepwalk()1543 /* power down the line state detectors of the port */ in tegra210_pmc_utmi_disable_phy_sleepwalk()1599 /* power down the line state detectors of the port */ in tegra210_pmc_hsic_enable_phy_sleepwalk()1633 /* power up the line state detectors of the port */ in tegra210_pmc_hsic_enable_phy_sleepwalk()1682 /* power down the line state detectors of the port */ in tegra210_pmc_hsic_disable_phy_sleepwalk()
373 /* power down the line state detectors of the pad */ in tegra186_utmi_enable_phy_sleepwalk()450 /* power up the line state detectors of the pad */ in tegra186_utmi_enable_phy_sleepwalk()512 /* power down the line state detectors of the port */ in tegra186_utmi_disable_phy_sleepwalk()
272 * types of issues than using memory leak detectors outside of
1120 * lockup detectors) and so should be last resort.
1102 * lockup detectors) and so should be last resort.
1674 0 Disable both lockup detectors.1675 1 Enable both lockup detectors.
483 as the generic hardlockup detectors.
1204 # Both the "perf" and "buddy" hardlockup detectors count hrtimer1316 that watchdogs and lockup detectors are working properly.
541 * we know it's not accurate (detectors can't measure anything outside1011 /* Tweak power detectors for half/quarter rate support */ in ath5k_hw_rfregs_init()
3278 /* detectors check period usec */