| /freebsd/sys/contrib/device-tree/Bindings/sound/ |
| H A D | cirrus,cs35l41.yaml | 42 cirrus,boost-peak-milliamp:
44 Boost-converter peak current limit in mA.
45 Configures the peak current by monitoring the current through the boost FET.
53 cirrus,boost-ind-nanohenry:
55 Boost inductor value, expressed in nH. Valid
61 cirrus,boost-cap-microfarad:
63 Total equivalent boost capacitance on the VBST
81 cirrus,boost-type:
83 Configures the type of Boost being used.
84 Internal boost requires boost-peak-milliamp, boost-ind-nanohenry and
[all …]
|
| H A D | cs35l36.txt | 13 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
18 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
19 Configures the peak current by monitoring the current through the boost FET.
24 - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
25 Seeds the digital boost converter's inductor estimation block with the initial
36 - cirrus,boost-ctl-select : Boost converte
[all...] |
| H A D | cs35l34.txt | 13 - cirrus,boost-vtge-millivolt : Boost Voltage Value. Configures the boost
17 - cirrus,boost-nanohenry: Inductor value for boost converter. The value is
28 - cirrus,boost-peak-milliamp : Boost converter peak current limit in mA. The
59 cirrus,boost-vtge-milltvolt = <8000>; /* 8V */
60 cirrus,boost-ind-nanohenry = <1000>; /* 1uH */
61 cirrus,boost-peak-milliamp = <3000>; /* 3A */
|
| H A D | cs35l35.txt | 17 - cirrus,boost-ind-nanohenry: Inductor value for boost converter. The value is
34 - cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal
35 if 2 Devices share Boost BST_CTL
37 - cirrus,external-boost : Boolean to specify the device is using an external
38 boost supply, note that sharing a boost from another cs35l35 would constitute
51 - cirrus,bst-pdn-fet-on : Boolean to determine if the Boost PDN control
55 - cirrus,boost-ctl-millivolt : Boost Voltag
[all...] |
| H A D | cs35l32.txt | 18 - cirrus,boost-manager : Boost voltage control.
19 0 = Automatically managed. Boost-converter output voltage is the higher
22 dissipation when LEDs are ON, and operating in Fixed-Boost Bypass Mode
24 2 = (Default) Boost voltage fixed in Bypass Mode (VBST = VP).
25 3 = Boost voltage fixed at 5 V.
59 cirrus,boost-manager = <0x03>;
|
| H A D | cs35l33.txt | 21 - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is
22 0, then VBST = VP. If greater than 0, the boost voltage will be 3300mV with
34 - cirrus,boost-ipk : The maximum current allowed for the boost converter.
109 cirrus,boost-ctl = <0x30>; /* VBST = 8000mV */
110 cirrus,boost-ipk = <0xE0>; /* 3600mA */
|
| /freebsd/sys/contrib/device-tree/Bindings/power/supply/ |
| H A D | bq25890.yaml | 58 ti,boost-voltage:
60 description: VBUS voltage level in boost mode (in uV)
62 ti,boost-max-current:
64 description: maximum allowed current draw in boost mode (in uA)
66 ti,boost-low-freq:
67 description: boost mode frequency will be 500kHz, otherwise 1.5MHz
97 - ti,boost-voltage
98 - ti,boost-max-current
121 ti,boost-voltage = <5000000>;
122 ti,boost-max-current = <1000000>;
|
| H A D | bq25890.txt | 23 - ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV);
24 - ti,boost-max-current: integer, maximum allowed current draw in boost mode
28 - ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz,
55 ti,boost-voltage = <5000000>;
56 ti,boost-max-current = <1000000>;
|
| H A D | richtek,rt9455.yaml | 39 richtek,boost-output-voltage:
42 maximum voltage provided to consumer devices, when the charger is in boost mode, in uV.
64 - richtek,boost-output-voltage
85 richtek,boost-output-voltage = <5050000>;
|
| H A D | rt9455_charger.txt | 16 - richtek,boost-output-voltage: integer, maximum voltage provided to consumer
17 devices, when the charger is in boost mode, in uV.
42 richtek,boost-output-voltage = <5050000>;
|
| H A D | mt6360_charger.yaml | 14 Provides Battery Charger, Boost for OTG devices and BC1.2 detection.
27 description: OTG boost regulator.
|
| H A D | mediatek,mt6370-charger.yaml | 14 Provides Battery Charger, Boost for OTG devices and BC1.2 detection.
80 description: OTG boost regulator.
|
| /freebsd/sys/contrib/device-tree/Bindings/mfd/ |
| H A D | max77693.txt | 89 - maxim,boost-mode :
90 In boost mode the device can produce up to 1.2A of total current
92 to 625mA then. If not enabled explicitly, boost setting defaults to
95 LEDS_BOOST_OFF (0) - no boost,
98 - maxim,boost-mvout : Output voltage of the boost module in millivolts.
117 (boost mode must be turned off):
182 maxim,boost-mode = <LEDS_BOOST_FIXED>;
183 maxim,boost-mvout = <5000>;
|
| H A D | st,stpmic1.yaml | 99 - boost for Buck BOOST
172 boost:
193 "^(buck[1-4]|ldo[1-6]|vref_ddr|boost|pwr_sw[1-2])-supply$":
|
| /freebsd/sys/contrib/device-tree/Bindings/leds/ |
| H A D | maxim,max77693.yaml | 28 maxim,boost-mode:
30 In boost mode the device can produce up to 1.2A of total current on both
32 not enabled explicitly, boost setting defaults to LEDS_BOOST_FIXED in
38 maxim,boost-mvout:
40 Output voltage of the boost module in millivolts.
83 (boost mode must be turned off):
|
| /freebsd/sys/contrib/device-tree/Bindings/regulator/ |
| H A D | onnn,fan53880.yaml | 15 and one BOOST (step-up converter) output. It is designed for mobile
38 description: Input supply phandle(s) for BUCK and BOOST
45 after their hardware counterparts LDO[1-4], BUCK and BOOST
53 "^BUCK|BOOST$":
|
| H A D | richtek,rt4803.yaml | 7 title: Richtek RT4803 Boost Regulator
13 RT4803 is a boost regulator that's designed to provide the minimum output
15 supports boost and auto bypass mode that depends on the difference between the
17 transform to boost mode. Otherwise, turn on bypass switch to enter bypass mode.
|
| H A D | qcom-labibb-regulator.yaml | 7 title: Qualcomm's LAB(LCD AMOLED Boost)/IBB(Inverting Buck Boost) Regulator
13 LAB can be used as a positive boost power supply and IBB can be used as a
14 negative boost power supply for display panels. Currently implemented for
|
| H A D | richtek,rtq6752-regulator.yaml | 14 two synchronous boost converter for PAVDD, and one synchronous NAVDD
15 buck-boost. The device is suitable for automotive TFT-LCD panel.
|
| /freebsd/sys/contrib/device-tree/Bindings/leds/backlight/ |
| H A D | qcom-wled.yaml | 77 qcom,current-boost-limit:
79 mA; boost current limit.
179 qcom,current-boost-limit:
200 qcom,current-boost-limit:
258 qcom,current-boost-limit = <805>;
|
| /freebsd/sys/contrib/device-tree/Bindings/ata/ |
| H A D | imx-sata.txt | 19 - fsl,transmit-boost-mdB : transmit boost level, in milli-decibels
|
| H A D | imx-sata.yaml | 45 fsl,transmit-boost-mdB:
47 description: transmit boost level, in milli-decibels.
|
| /freebsd/sys/contrib/device-tree/Bindings/display/panel/ |
| H A D | ebbg,ft8719.yaml | 32 description: positive boost supply regulator
35 description: negative boost supply regulator
|
| H A D | novatek,nt36672a.yaml | 42 description: phandle of the positive boost supply regulator
45 description: phandle of the negative boost supply regulator
|
| /freebsd/sys/contrib/device-tree/Bindings/display/bridge/ |
| H A D | analogix,anx7625.yaml | 53 Swing1_Pre2, Swing0_Pre3, they are for [Boost control] and
55 Registers 0~9, bit 3:0 is [Boost control], these bits control
56 post cursor manual, increase the [Boost control] to increase
|