| /linux/drivers/net/ethernet/marvell/octeontx2/af/ |
| H A D | lmac_common.h | 63 /* For ATF to send events to kernel, there is no dedicated interrupt
65 * SW_INT so that ATF triggers this interrupt after processing of
|
| H A D | cgx_fw_if.h | 187 /* scratchx(0) CSR used for ATF->non-secure SW communication.
260 /* scratchx(1) CSR used for non-secure SW->ATF communication
|
| /linux/arch/arm/boot/dts/airoha/ |
| H A D | en7523-evb.dts | 4 /* Bootloader installs ATF here */
|
| /linux/Documentation/devicetree/bindings/watchdog/ |
| H A D | arm-smc-wdt.yaml | 23 The ATF smc function id used by the firmware.
|
| /linux/Documentation/devicetree/bindings/fpga/ |
| H A D | intel,stratix10-soc-fpga-mgr.yaml | 18 on the die.The driver communicates with SDM/ATF via the stratix10-svc
|
| /linux/include/dt-bindings/clock/ |
| H A D | rk3399-ddr.h | 53 /* DDR3 ATF default */
|
| /linux/arch/arm64/boot/dts/airoha/ |
| H A D | en7581-evb.dts | 4 /* Bootloader installs ATF here */
|
| /linux/drivers/clk/zynqmp/ |
| H A D | pll.c | 17 * @set_pll_mode: Whether an IOCTL_SET_PLL_FRAC_MODE request be sent to ATF
258 * that has been sent to ATF. in zynqmp_pll_enable()
|
| /linux/arch/arm/boot/dts/st/ |
| H A D | stm32mp157c-odyssey.dts | 41 assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF/U-Boot */
|
| H A D | stm32mp153c-lxa-fairytux2.dtsi | 116 assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF */
|
| /linux/drivers/net/can/flexcan/ |
| H A D | flexcan.h | 71 /* Setup stop mode with ATF SCMI protocol to support wakeup */
|
| /linux/Documentation/devicetree/bindings/firmware/ |
| H A D | fsl,scu.yaml | 70 execution environments such as ATF.
|
| /linux/include/linux/firmware/ |
| H A D | xlnx-zynqmp.h | 72 /* ATF only commands */
237 /* Register SGI to ATF */
|
| /linux/drivers/net/ethernet/broadcom/ |
| H A D | bgmac-platform.c | 87 /* Some bits of BCMA_IOCTL set by HW/ATF and should not change */ in platform_bgmac_clk_enable()
|
| /linux/drivers/clocksource/ |
| H A D | timer-mediatek.c | 265 * or for example ATF will prevent a suspend from completing. in mtk_gpt_suspend()
|
| /linux/drivers/soc/imx/ |
| H A D | soc-imx8m.c | 81 * the value from ATF instead. in imx8mq_soc_revision()
|
| /linux/drivers/clk/mediatek/ |
| H A D | clk-mt8195-infra_ao.c | 143 /* pwrmcu is used by ATF for platform PM: clocks must never be disabled by the kernel */
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-platform-devices-ampere-smpro | 292 - 02: ATF BL1 firmware booting
295 - 05: ATF BL2 firmware booting
296 - 06: ATF BL31 firmware booting
297 - 07: ATF BL32 firmware booting
|
| /linux/drivers/clk/mvebu/ |
| H A D | armada-37xx-periph.c | 715 /* Follow the same order than what the Cortex-M3 does (ATF code) */ in armada_3700_periph_clock_resume()
|
| /linux/arch/arm64/boot/dts/broadcom/ |
| H A D | bcm2712.dtsi | 182 atf@0 {
|
| /linux/drivers/platform/mellanox/ |
| H A D | mlxbf-bootctl.c | 27 /* UUID used to probe ATF service. */
|
| /linux/arch/arm64/boot/dts/ti/ |
| H A D | k3-j721e-common-proc-board.dts | 458 /* Shared with ATF on this platform */
|
| /linux/drivers/net/wireless/ath/ath10k/ |
| H A D | wmi.h | 2960 /* ATF configuration.
2961 * 1 - Enable ATF
2962 * 0 - Disable ATF
|
| /linux/drivers/parport/ |
| H A D | parport_pc.c | 1133 type = "83977ATF"; in decode_winbond()
1152 type = "83877ATF"; in decode_winbond()
|
| /linux/drivers/firmware/xilinx/ |
| H A D | zynqmp.c | 171 * (no direct communication with ATF).
|