| /linux/drivers/input/mouse/ |
| H A D | synaptics.c | 3 * Synaptics TouchPad PS/2 mouse driver
196 "SYN3015", /* HP EliteBook 840 G2 */
197 "SYN3052", /* HP EliteBook 840 G4 */
636 * Synaptics pass-through PS/2 port support
1610 * Unfortunately ForcePad capability is not exported over PS/2, in synaptics_init_ps2()
1653 /* Relative mode follows standard PS/2 mouse protocol */ in synaptics_init_ps2()
1672 * the same rate as a standard PS/2 mouse). in synaptics_init_ps2()
1815 * synaptics_setup_intertouch - called once the PS/2 devices are enumerated
1915 "The touchpad can support a better bus than the too old PS/2 protocol. " in synaptics_init()
|
| /linux/arch/parisc/kernel/ |
| H A D | hardware.c | 29 {HPHW_NPROC,0x01,0x4,0x0,"Indigo (840, 930)"},
921 {HPHW_FIO, 0x015, 0x00084, 0x0, "KittyHawk GSY Core PS/2 Port"},
922 {HPHW_FIO, 0x016, 0x00084, 0x0, "Gecko Core PS/2 Port"},
923 {HPHW_FIO, 0x018, 0x00084, 0x0, "Gecko Optional PS/2 Port"},
924 {HPHW_FIO, 0x01A, 0x00084, 0x0, "Anole 64 Core PS/2 Port"},
925 {HPHW_FIO, 0x01B, 0x00084, 0x0, "Anole 100 Core PS/2 Port"},
926 {HPHW_FIO, 0x01C, 0x00084, 0x0, "Gecko 80 Core PS/2 Port"},
927 {HPHW_FIO, 0x01D, 0x00084, 0x0, "Gecko 100 Core PS/2 Port"},
928 {HPHW_FIO, 0x01F, 0x00084, 0x0, "SkyHawk 100/120 Core PS/2 Port"},
929 {HPHW_FIO, 0x027, 0x00084, 0x0, "Piranha 100 Core PS/2 Port"},
[all …]
|
| /linux/arch/arm64/boot/dts/renesas/ |
| H A D | r8a779a0.dtsi | 147 interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
733 rx-internal-delay-ps = <0>;
734 tx-internal-delay-ps = <0>;
782 rx-internal-delay-ps = <0>;
783 tx-internal-delay-ps = <0>;
829 rx-internal-delay-ps = <0>;
830 tx-internal-delay-ps = <0>;
876 rx-internal-delay-ps = <0>;
877 tx-internal-delay-ps = <0>;
923 rx-internal-delay-ps
[all...] |
| /linux/drivers/parport/ |
| H A D | parport_pc.c | 973 "SPP and Bidirectional (PS/2)", in show_parconfig_smsc37c669()
1053 "Standard (SPP) and Bidirectional(PS/2)", /* 0 */ in show_parconfig_winbond()
1534 /* Detect PS/2 support.
1536 * Bit 5 (0x20) sets the PS/2 data direction; setting this high
1540 * of the data register we deem PS/2 support to be present.
1542 * Some SPP ports have "half PS/2" ability - you can't turn off the line
2464 printk(KERN_DEBUG "parport_pc: setting PS/2 mode\n"); in sio_via_probe()
2500 /* Bit 5: EPP+ECP enable; bit 7: PS/2 bidirectional port enable */ in sio_via_probe()
2715 * support ECP, and 840 locks up if you write 1 to bit 2! None
|
| /linux/drivers/net/wireless/ath/wil6210/ |
| H A D | wmi.c | 2658 /* typical time for secure PCP is 840ms */ in wmi_rx_chain_add()
2952 wil_dbg_wmi(wil, "Setting ps dev profile %d\n", ps_profile); in wmi_ps_dev_profile_cfg()
2964 wil_err(wil, "ps dev profile cfg failed with status %d\n", in wmi_ps_dev_profile_cfg()
|
| /linux/drivers/ata/ |
| H A D | libata-core.c | 8 * libata documentation is available via 'make {ps|pdf}docs',
4122 { "E-IDE CD-ROM CR-840", NULL, ATA_QUIRK_NODMA },
4303 { "Samsung SSD 840 EVO*", NULL, ATA_QUIRK_NO_NCQ_TRIM |
4306 { "Samsung SSD 840*", NULL, ATA_QUIRK_NO_NCQ_TRIM |
|
| /linux/arch/powerpc/xmon/ |
| H A D | ppc-opc.c | 767 /* The PS field in a VX form instruction. */
768 #define PS SIX + 1 macro
772 #define SHB PS + 1
2547 /* A VX_MASK with a PS field. */
2550 /* A VX_MASK with the VA field fixed with a PS field. */
3479 {"vmulesh", VX (4, 840), VX_MASK, PPCVEC, 0, {VD, VA, VB}},
3515 {"bcdadd.", VX (4,1025), VXPS_MASK, PPCVEC2, 0, {VD, VA, VB, PS}},
3547 {"bcdsub.", VX (4,1089), VXPS_MASK, PPCVEC2, 0, {VD, VA, VB, PS}},
3600 {"bcds.", VX (4,1217), VXPS_MASK, PPCVEC3, 0, {VD, VA, VB, PS}},
3626 {"bcdtrunc.", VX (4,1281), VXPS_MASK, PPCVEC3, 0, {VD, VA, VB, PS}},
[all …]
|