Home
last modified time | relevance | path

Searched +full:25 +full:gbase +full:- +full:kr (Results 1 – 5 of 5) sorted by relevance

/linux/Documentation/devicetree/bindings/phy/
H A Dtransmit-amplitude.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/phy/transmit-amplitude.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 Binding describing the peak-to-peak transmit amplitude for common PHYs
14 - Marek Behún <kabel@kernel.org>
17 tx-p2p-microvolt:
19 Transmit amplitude voltages in microvolts, peak-to-peak. If this property
21 'tx-p2p-microvolt-names' property must be provided and contain
24 tx-p2p-microvolt-names:
[all …]
/linux/include/linux/
H A Dmdio.h1 /* SPDX-License-Identifier: GPL-2.0-only */
4 * Copyright 2006-2009 Solarflare Communications Inc.
38 /* Bus address of the MDIO device (0-31) */
66 * up device-specific structures, if any
83 dev_set_drvdata(&mdio->dev, data); in mdiodev_set_drvdata()
88 return dev_get_drvdata(&mdio->dev); in mdiodev_get_drvdata()
101 get_device(&mdiodev->dev); in mdio_device_get()
125 * struct mdio_if_info - Ethernet controller MDIO interface
128 * non-zero unless @prtad = %MDIO_PRTAD_NONE.
150 #define MDIO_PRTAD_NONE (-1)
[all …]
/linux/drivers/net/ethernet/sfc/
H A Dmcdi_pcol.h1 /* SPDX-License-Identifier: GPL-2.0-only */
4 * Copyright 2009-2018 Solarflare Communications Inc.
5 * Copyright 2019-2020 Xilinx Inc.
13 /* Power-on reset state */
35 /* The 'doorbell' addresses are hard-wired to alert the MC when written */
38 /* The rest of these are firmware-defined */
46 /* Values to be written to the per-port status dword in shared
71 * | | \--- Response
72 * | \------- Error
73 * \------------------------------ Resync (always set)
[all …]
/linux/drivers/net/ethernet/freescale/fman/
H A Dfman_memac.c1 // SPDX-License-Identifier: BSD-3-Clause OR GPL-2.0-or-later
3 * Copyright 2008 - 2015 Freescale Semiconductor Inc.
14 #include <linux/pcs-lynx.h>
31 #define CMD_CFG_CRC_FWD 0x00000040 /* 25 Terminate/frwd CRC of frames */
56 #define IF_MODE_MASK 0x00000003 /* 30-31 Mask on i/f mode bits */
57 #define IF_MODE_10G 0x00000000 /* 30-31 10G interface */
58 #define IF_MODE_MII 0x00000001 /* 30-31 MII interface */
59 #define IF_MODE_GMII 0x00000002 /* 30-31 GMII (1G) interface */
62 #define IF_MODE_RGMII_1000 0x00004000 /* 10 - 1000Mbps RGMII */
63 #define IF_MODE_RGMII_100 0x00000000 /* 00 - 100Mbps RGMII */
[all …]
/linux/drivers/net/ethernet/broadcom/bnx2x/
H A Dbnx2x_hsi.h3 * Copyright (c) 2007-2013 Broadcom Corporation
125 /* Up to 16 bytes of NULL-terminated string */
145 (if multiple found, priority order is: NC-SI, UMP, IPMI) */
150 /* Use SPIO4 as an arbiter between: 0-NC_SI, 1-IPMI
151 (can only be used when an add-in board, not BMC, pulls-down SPIO4) */
153 /* Use SPIO4 as an arbiter between: 0-UMP, 1-IPMI
154 (can only be used when an add-in board, not BMC, pulls-down SPIO4) */
156 /* Use SPIO4 as an arbiter between: 0-NC-SI, 1-UMP
157 (can only be used when an add-in board, not BMC, pulls-down SPIO4) */
409 /* Default values: 2P-64, 4P-32 */
[all …]