| /linux/arch/arm/mach-omap1/ |
| H A D | usb.c | 35 * - 1510 Innovator UDC with bundled usb0 cable
36 * - 1510 Innovator OHCI with bundled usb1/usb2 cable
37 * - 1510 Innovator OHCI with custom usb0 cable, feeding 5V VBUS
300 /* This works on 1510-Innovator */ in omap1_usb0_init()
511 /* OMAP-1510 OHCI has its own MMU for DMA */
523 * Bus address is physical address, except for OMAP-1510 Local Bus.
524 * OMAP-1510 bus address is translated into a Local Bus address if the
530 * OMAP-1510 specific Local Bus clock on/off
545 * OMAP-1510 specific Local Bus initialization
|
| H A D | irqs.h | 9 * NOTE: The interrupt vectors for the OMAP-1509, OMAP-1510, and OMAP-1610
19 * NOTE: See also the OMAP-1510 and 1610 specific IRQ numbers below
45 * OMAP-1510 specific IRQ numbers for interrupt handler 1
97 * NOTE: See also the OMAP-1510 and 1610 specific IRQ numbers below
126 * OMAP-1510 specific IRQ numbers for interrupt handler 2
|
| H A D | mux.h | 14 * - 1610 = 1510 or 1610, none if common for both 1510 and 1610
|
| H A D | id.c | 71 * 1510 PROD_ID is empty, and 1610 PROD_ID does not make sense.
73 * work on 1510, 1610 & 1710. The official way hopefully will work in future
102 * REVISIT: This does not seem to work on 1510
|
| H A D | timer32k.c | 61 * This currently works only on 16xx, as 1510 does not have the continuous
64 * on 1510 would be possible, but the timer would not be as accurate as
168 * OMAP 730 and 1510. Other timers could be used as clocksources, with
|
| H A D | serial.c | 103 * Note that on Innovator-1510 UART2 pins conflict with USB2.
104 * By default UART2 does not work on Innovator-1510 if you have
|
| H A D | clock_data.c | 142 * activation. [ GPIO code for 1510 ]
193 * 1510 version is in TC clocks.
255 /* Note: On 1510 the frequency follows TC_CK
473 /* OTG_SYSCON_2.OTG_PADEN == 0 (not 1510-compatible) */
554 * XXX MOD_CONF_CTRL_0 bit 20 is defined in the 1510 TRM as
|
| H A D | mcbsp.c | 38 * On 1510, 1610 and 1710, McBSP1 and McBSP3 in omap1_mcbsp_request()
|
| H A D | sleep.S | 4 * Low-level OMAP7XX/1510/1610 sleep/wakeUp support
|
| H A D | mux.c | 83 /* OMAP-1510 GPIO */
187 /* First MMC interface, same on 1510, 1610 and 1710 */
|
| H A D | omap-dma.c | 402 * Disable the 1510 compatibility mode and set the sync device in omap_request_dma()
|
| /linux/include/linux/soc/ti/ |
| H A D | omap1-soc.h | 42 * CPU id bits (0730, 1510, 1710, 2422...) [31:16]
121 IS_OMAP_TYPE(1510, 0x1510)
140 * between 310 vs. 1510 and 1611B/5912 vs. 1710.
|
| H A D | omap1-mux.h | 106 /* OMAP-1510 GPIO */
|
| /linux/arch/arm/boot/dts/broadcom/ |
| H A D | bcm4708-luxul-xap-1510.dts | 11 compatible = "luxul,xap-1510-v1", "brcm,bcm4708";
12 model = "Luxul XAP-1510 V1";
|
| /linux/drivers/clocksource/ |
| H A D | timer-ti-32k.c | 37 * OMAP 730 and 1510. Other timers could be used as clocksources, with
|
| /linux/tools/testing/selftests/tc-testing/tc-tests/qdiscs/ |
| H A D | tbf.json | 56 … qdisc add dev $DUMMY handle 1: root tbf limit 1000 burst 1500 rate 20000 mtu 1510 peakrate 30000",
|
| /linux/Documentation/scsi/ |
| H A D | aha152x.rst | 46 Don't test for BIOS signature (AHA-1510 or disabled BIOS)
|
| /linux/drivers/ata/ |
| H A D | pata_rdc.c | 6 * INCITS 370-2004 (1510D): ATA Host Adapter Standards
|
| /linux/arch/arm/mach-omap2/ |
| H A D | soc.h | 46 * SoC id bits (0730, 1510, 1710, 2422...) [31:16]
|
| /linux/arch/arm/mm/ |
| H A D | proc-arm925.S | 35 * the default for OMAP-1510).
|
| /linux/arch/x86/math-emu/ |
| H A D | README | 379 63.1 20016 8288 0 4620 6628 511 2569 1723 1510 3302
|
| /linux/drivers/input/keyboard/ |
| H A D | atkbd.c | 1891 /* Fujitsu Amilo PA 1510 */
1894 DMI_MATCH(DMI_PRODUCT_NAME, "AMILO Pa 1510"),
|
| /linux/drivers/iio/adc/ |
| H A D | ad7280a.c | 141 static const unsigned short ad7280a_t_acq_ns[4] = {470, 1030, 1510, 1945};
|
| /linux/sound/soc/codecs/ |
| H A D | wsa881x.c | 817 usleep_range(1500, 1510); in wsa881x_boost_ctrl()
|
| /linux/sound/soc/ti/ |
| H A D | omap-mcbsp.c | 611 * McBSP1 and McBSP3 are directly mapped on 1610 and 1510.
|