1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * wm8960.c -- WM8960 ALSA SoC Audio driver
4 *
5 * Copyright 2007-11 Wolfson Microelectronics, plc
6 *
7 * Author: Liam Girdwood
8 */
9
10 #include <linux/module.h>
11 #include <linux/moduleparam.h>
12 #include <linux/init.h>
13 #include <linux/delay.h>
14 #include <linux/pm.h>
15 #include <linux/clk.h>
16 #include <linux/i2c.h>
17 #include <linux/acpi.h>
18 #include <linux/slab.h>
19 #include <sound/core.h>
20 #include <sound/pcm.h>
21 #include <sound/pcm_params.h>
22 #include <sound/soc.h>
23 #include <sound/initval.h>
24 #include <sound/tlv.h>
25 #include <sound/wm8960.h>
26
27 #include "wm8960.h"
28
29 /* R25 - Power 1 */
30 #define WM8960_VMID_MASK 0x180
31 #define WM8960_VREF 0x40
32
33 /* R26 - Power 2 */
34 #define WM8960_PWR2_LOUT1 0x40
35 #define WM8960_PWR2_ROUT1 0x20
36 #define WM8960_PWR2_OUT3 0x02
37
38 /* R28 - Anti-pop 1 */
39 #define WM8960_POBCTRL 0x80
40 #define WM8960_BUFDCOPEN 0x10
41 #define WM8960_BUFIOEN 0x08
42 #define WM8960_SOFT_ST 0x04
43 #define WM8960_HPSTBY 0x01
44
45 /* R29 - Anti-pop 2 */
46 #define WM8960_DISOP 0x40
47 #define WM8960_DRES_MASK 0x30
48
49 #define WM8960_DSCH_TOUT 600 /* discharge timeout, ms */
50
51 static bool is_pll_freq_available(unsigned int source, unsigned int target);
52 static int wm8960_set_pll(struct snd_soc_component *component,
53 unsigned int freq_in, unsigned int freq_out);
54 /*
55 * wm8960 register cache
56 * We can't read the WM8960 register space when we are
57 * using 2 wire for device control, so we cache them instead.
58 */
59 static const struct reg_default wm8960_reg_defaults[] = {
60 { 0x0, 0x00a7 },
61 { 0x1, 0x00a7 },
62 { 0x2, 0x0000 },
63 { 0x3, 0x0000 },
64 { 0x4, 0x0000 },
65 { 0x5, 0x0008 },
66 { 0x6, 0x0000 },
67 { 0x7, 0x000a },
68 { 0x8, 0x01c0 },
69 { 0x9, 0x0000 },
70 { 0xa, 0x00ff },
71 { 0xb, 0x00ff },
72
73 { 0x10, 0x0000 },
74 { 0x11, 0x007b },
75 { 0x12, 0x0100 },
76 { 0x13, 0x0032 },
77 { 0x14, 0x0000 },
78 { 0x15, 0x00c3 },
79 { 0x16, 0x00c3 },
80 { 0x17, 0x01c0 },
81 { 0x18, 0x0000 },
82 { 0x19, 0x0000 },
83 { 0x1a, 0x0000 },
84 { 0x1b, 0x0000 },
85 { 0x1c, 0x0000 },
86 { 0x1d, 0x0000 },
87
88 { 0x20, 0x0100 },
89 { 0x21, 0x0100 },
90 { 0x22, 0x0050 },
91
92 { 0x25, 0x0050 },
93 { 0x26, 0x0000 },
94 { 0x27, 0x0000 },
95 { 0x28, 0x0000 },
96 { 0x29, 0x0000 },
97 { 0x2a, 0x0040 },
98 { 0x2b, 0x0000 },
99 { 0x2c, 0x0000 },
100 { 0x2d, 0x0050 },
101 { 0x2e, 0x0050 },
102 { 0x2f, 0x0000 },
103 { 0x30, 0x0002 },
104 { 0x31, 0x0037 },
105
106 { 0x33, 0x0080 },
107 { 0x34, 0x0008 },
108 { 0x35, 0x0031 },
109 { 0x36, 0x0026 },
110 { 0x37, 0x00e9 },
111 };
112
wm8960_volatile(struct device * dev,unsigned int reg)113 static bool wm8960_volatile(struct device *dev, unsigned int reg)
114 {
115 switch (reg) {
116 case WM8960_RESET:
117 return true;
118 default:
119 return false;
120 }
121 }
122
123 #define WM8960_NUM_SUPPLIES 5
124 static const char *wm8960_supply_names[WM8960_NUM_SUPPLIES] = {
125 "DCVDD",
126 "DBVDD",
127 "AVDD",
128 "SPKVDD1",
129 "SPKVDD2",
130 };
131
132 struct wm8960_priv {
133 struct clk *mclk;
134 struct regmap *regmap;
135 int (*set_bias_level)(struct snd_soc_component *,
136 enum snd_soc_bias_level level);
137 struct snd_soc_dapm_widget *lout1;
138 struct snd_soc_dapm_widget *rout1;
139 struct snd_soc_dapm_widget *out3;
140 bool deemph;
141 int lrclk;
142 int bclk;
143 int sysclk;
144 int clk_id;
145 int freq_in;
146 bool is_stream_in_use[2];
147 struct wm8960_data pdata;
148 ktime_t dsch_start;
149 struct regulator_bulk_data supplies[WM8960_NUM_SUPPLIES];
150 };
151
152 #define wm8960_reset(c) regmap_write(c, WM8960_RESET, 0)
153
154 /* enumerated controls */
155 static const char *wm8960_polarity[] = {"No Inversion", "Left Inverted",
156 "Right Inverted", "Stereo Inversion"};
157 static const char *wm8960_3d_upper_cutoff[] = {"High", "Low"};
158 static const char *wm8960_3d_lower_cutoff[] = {"Low", "High"};
159 static const char *wm8960_alcfunc[] = {"Off", "Right", "Left", "Stereo"};
160 static const char *wm8960_alcmode[] = {"ALC", "Limiter"};
161 static const char *wm8960_adc_data_output_sel[] = {
162 "Left Data = Left ADC; Right Data = Right ADC",
163 "Left Data = Left ADC; Right Data = Left ADC",
164 "Left Data = Right ADC; Right Data = Right ADC",
165 "Left Data = Right ADC; Right Data = Left ADC",
166 };
167 static const char *wm8960_dmonomix[] = {"Stereo", "Mono"};
168 static const char *wm8960_dacslope[] = {"Normal", "Sloping"};
169
170 static const struct soc_enum wm8960_enum[] = {
171 SOC_ENUM_SINGLE(WM8960_DACCTL1, 5, 4, wm8960_polarity),
172 SOC_ENUM_SINGLE(WM8960_DACCTL2, 5, 4, wm8960_polarity),
173 SOC_ENUM_SINGLE(WM8960_3D, 6, 2, wm8960_3d_upper_cutoff),
174 SOC_ENUM_SINGLE(WM8960_3D, 5, 2, wm8960_3d_lower_cutoff),
175 SOC_ENUM_SINGLE(WM8960_ALC1, 7, 4, wm8960_alcfunc),
176 SOC_ENUM_SINGLE(WM8960_ALC3, 8, 2, wm8960_alcmode),
177 SOC_ENUM_SINGLE(WM8960_ADDCTL1, 2, 4, wm8960_adc_data_output_sel),
178 SOC_ENUM_SINGLE(WM8960_ADDCTL1, 4, 2, wm8960_dmonomix),
179 SOC_ENUM_SINGLE(WM8960_DACCTL2, 1, 2, wm8960_dacslope),
180 };
181
182 static const int deemph_settings[] = { 0, 32000, 44100, 48000 };
183
wm8960_set_deemph(struct snd_soc_component * component)184 static int wm8960_set_deemph(struct snd_soc_component *component)
185 {
186 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
187 int val, i, best;
188
189 /* If we're using deemphasis select the nearest available sample
190 * rate.
191 */
192 if (wm8960->deemph) {
193 best = 1;
194 for (i = 2; i < ARRAY_SIZE(deemph_settings); i++) {
195 if (abs(deemph_settings[i] - wm8960->lrclk) <
196 abs(deemph_settings[best] - wm8960->lrclk))
197 best = i;
198 }
199
200 val = best << 1;
201 } else {
202 val = 0;
203 }
204
205 dev_dbg(component->dev, "Set deemphasis %d\n", val);
206
207 return snd_soc_component_update_bits(component, WM8960_DACCTL1,
208 0x6, val);
209 }
210
wm8960_get_deemph(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)211 static int wm8960_get_deemph(struct snd_kcontrol *kcontrol,
212 struct snd_ctl_elem_value *ucontrol)
213 {
214 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
215 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
216
217 ucontrol->value.integer.value[0] = wm8960->deemph;
218 return 0;
219 }
220
wm8960_put_deemph(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)221 static int wm8960_put_deemph(struct snd_kcontrol *kcontrol,
222 struct snd_ctl_elem_value *ucontrol)
223 {
224 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
225 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
226 unsigned int deemph = ucontrol->value.integer.value[0];
227
228 if (deemph > 1)
229 return -EINVAL;
230
231 wm8960->deemph = deemph;
232
233 return wm8960_set_deemph(component);
234 }
235
236 static const DECLARE_TLV_DB_SCALE(adc_tlv, -9750, 50, 1);
237 static const DECLARE_TLV_DB_SCALE(inpga_tlv, -1725, 75, 0);
238 static const DECLARE_TLV_DB_SCALE(dac_tlv, -12750, 50, 1);
239 static const DECLARE_TLV_DB_SCALE(bypass_tlv, -2100, 300, 0);
240 static const DECLARE_TLV_DB_SCALE(out_tlv, -12100, 100, 1);
241 static const DECLARE_TLV_DB_SCALE(lineinboost_tlv, -1500, 300, 1);
242 static const SNDRV_CTL_TLVD_DECLARE_DB_RANGE(micboost_tlv,
243 0, 1, TLV_DB_SCALE_ITEM(0, 1300, 0),
244 2, 3, TLV_DB_SCALE_ITEM(2000, 900, 0),
245 );
246
247 static const struct snd_kcontrol_new wm8960_snd_controls[] = {
248 SOC_DOUBLE_R_TLV("Capture Volume", WM8960_LINVOL, WM8960_RINVOL,
249 0, 63, 0, inpga_tlv),
250 SOC_DOUBLE_R("Capture Volume ZC Switch", WM8960_LINVOL, WM8960_RINVOL,
251 6, 1, 0),
252 SOC_DOUBLE_R("Capture Switch", WM8960_LINVOL, WM8960_RINVOL,
253 7, 1, 1),
254
255 SOC_SINGLE_TLV("Left Input Boost Mixer LINPUT3 Volume",
256 WM8960_INBMIX1, 4, 7, 0, lineinboost_tlv),
257 SOC_SINGLE_TLV("Left Input Boost Mixer LINPUT2 Volume",
258 WM8960_INBMIX1, 1, 7, 0, lineinboost_tlv),
259 SOC_SINGLE_TLV("Right Input Boost Mixer RINPUT3 Volume",
260 WM8960_INBMIX2, 4, 7, 0, lineinboost_tlv),
261 SOC_SINGLE_TLV("Right Input Boost Mixer RINPUT2 Volume",
262 WM8960_INBMIX2, 1, 7, 0, lineinboost_tlv),
263 SOC_SINGLE_TLV("Right Input Boost Mixer RINPUT1 Volume",
264 WM8960_RINPATH, 4, 3, 0, micboost_tlv),
265 SOC_SINGLE_TLV("Left Input Boost Mixer LINPUT1 Volume",
266 WM8960_LINPATH, 4, 3, 0, micboost_tlv),
267
268 SOC_DOUBLE_R_TLV("Playback Volume", WM8960_LDAC, WM8960_RDAC,
269 0, 255, 0, dac_tlv),
270
271 SOC_DOUBLE_R_TLV("Headphone Playback Volume", WM8960_LOUT1, WM8960_ROUT1,
272 0, 127, 0, out_tlv),
273 SOC_DOUBLE_R("Headphone Playback ZC Switch", WM8960_LOUT1, WM8960_ROUT1,
274 7, 1, 0),
275
276 SOC_DOUBLE_R_TLV("Speaker Playback Volume", WM8960_LOUT2, WM8960_ROUT2,
277 0, 127, 0, out_tlv),
278 SOC_DOUBLE_R("Speaker Playback ZC Switch", WM8960_LOUT2, WM8960_ROUT2,
279 7, 1, 0),
280 SOC_SINGLE("Speaker DC Volume", WM8960_CLASSD3, 3, 5, 0),
281 SOC_SINGLE("Speaker AC Volume", WM8960_CLASSD3, 0, 5, 0),
282
283 SOC_SINGLE("PCM Playback -6dB Switch", WM8960_DACCTL1, 7, 1, 0),
284 SOC_ENUM("ADC Polarity", wm8960_enum[0]),
285 SOC_SINGLE("ADC High Pass Filter Switch", WM8960_DACCTL1, 0, 1, 0),
286
287 SOC_ENUM("DAC Polarity", wm8960_enum[1]),
288 SOC_SINGLE_BOOL_EXT("DAC Deemphasis Switch", 0,
289 wm8960_get_deemph, wm8960_put_deemph),
290
291 SOC_ENUM("3D Filter Upper Cut-Off", wm8960_enum[2]),
292 SOC_ENUM("3D Filter Lower Cut-Off", wm8960_enum[3]),
293 SOC_SINGLE("3D Volume", WM8960_3D, 1, 15, 0),
294 SOC_SINGLE("3D Switch", WM8960_3D, 0, 1, 0),
295
296 SOC_ENUM("ALC Function", wm8960_enum[4]),
297 SOC_SINGLE("ALC Max Gain", WM8960_ALC1, 4, 7, 0),
298 SOC_SINGLE("ALC Target", WM8960_ALC1, 0, 15, 1),
299 SOC_SINGLE("ALC Min Gain", WM8960_ALC2, 4, 7, 0),
300 SOC_SINGLE("ALC Hold Time", WM8960_ALC2, 0, 15, 0),
301 SOC_ENUM("ALC Mode", wm8960_enum[5]),
302 SOC_SINGLE("ALC Decay", WM8960_ALC3, 4, 15, 0),
303 SOC_SINGLE("ALC Attack", WM8960_ALC3, 0, 15, 0),
304
305 SOC_SINGLE("Noise Gate Threshold", WM8960_NOISEG, 3, 31, 0),
306 SOC_SINGLE("Noise Gate Switch", WM8960_NOISEG, 0, 1, 0),
307
308 SOC_DOUBLE_R_TLV("ADC PCM Capture Volume", WM8960_LADC, WM8960_RADC,
309 0, 255, 0, adc_tlv),
310
311 SOC_SINGLE_TLV("Left Output Mixer Boost Bypass Volume",
312 WM8960_BYPASS1, 4, 7, 1, bypass_tlv),
313 SOC_SINGLE_TLV("Left Output Mixer LINPUT3 Volume",
314 WM8960_LOUTMIX, 4, 7, 1, bypass_tlv),
315 SOC_SINGLE_TLV("Right Output Mixer Boost Bypass Volume",
316 WM8960_BYPASS2, 4, 7, 1, bypass_tlv),
317 SOC_SINGLE_TLV("Right Output Mixer RINPUT3 Volume",
318 WM8960_ROUTMIX, 4, 7, 1, bypass_tlv),
319
320 SOC_ENUM("ADC Data Output Select", wm8960_enum[6]),
321 SOC_ENUM("DAC Mono Mix", wm8960_enum[7]),
322 SOC_ENUM("DAC Filter Characteristics", wm8960_enum[8]),
323 };
324
325 static const struct snd_kcontrol_new wm8960_lin_boost[] = {
326 SOC_DAPM_SINGLE("LINPUT2 Switch", WM8960_LINPATH, 6, 1, 0),
327 SOC_DAPM_SINGLE("LINPUT3 Switch", WM8960_LINPATH, 7, 1, 0),
328 SOC_DAPM_SINGLE("LINPUT1 Switch", WM8960_LINPATH, 8, 1, 0),
329 };
330
331 static const struct snd_kcontrol_new wm8960_lin[] = {
332 SOC_DAPM_SINGLE("Boost Switch", WM8960_LINPATH, 3, 1, 0),
333 };
334
335 static const struct snd_kcontrol_new wm8960_rin_boost[] = {
336 SOC_DAPM_SINGLE("RINPUT2 Switch", WM8960_RINPATH, 6, 1, 0),
337 SOC_DAPM_SINGLE("RINPUT3 Switch", WM8960_RINPATH, 7, 1, 0),
338 SOC_DAPM_SINGLE("RINPUT1 Switch", WM8960_RINPATH, 8, 1, 0),
339 };
340
341 static const struct snd_kcontrol_new wm8960_rin[] = {
342 SOC_DAPM_SINGLE("Boost Switch", WM8960_RINPATH, 3, 1, 0),
343 };
344
345 static const struct snd_kcontrol_new wm8960_loutput_mixer[] = {
346 SOC_DAPM_SINGLE("PCM Playback Switch", WM8960_LOUTMIX, 8, 1, 0),
347 SOC_DAPM_SINGLE("LINPUT3 Switch", WM8960_LOUTMIX, 7, 1, 0),
348 SOC_DAPM_SINGLE("Boost Bypass Switch", WM8960_BYPASS1, 7, 1, 0),
349 };
350
351 static const struct snd_kcontrol_new wm8960_routput_mixer[] = {
352 SOC_DAPM_SINGLE("PCM Playback Switch", WM8960_ROUTMIX, 8, 1, 0),
353 SOC_DAPM_SINGLE("RINPUT3 Switch", WM8960_ROUTMIX, 7, 1, 0),
354 SOC_DAPM_SINGLE("Boost Bypass Switch", WM8960_BYPASS2, 7, 1, 0),
355 };
356
357 static const struct snd_kcontrol_new wm8960_mono_out[] = {
358 SOC_DAPM_SINGLE("Left Switch", WM8960_MONOMIX1, 7, 1, 0),
359 SOC_DAPM_SINGLE("Right Switch", WM8960_MONOMIX2, 7, 1, 0),
360 };
361
362 static const struct snd_soc_dapm_widget wm8960_dapm_widgets[] = {
363 SND_SOC_DAPM_INPUT("LINPUT1"),
364 SND_SOC_DAPM_INPUT("RINPUT1"),
365 SND_SOC_DAPM_INPUT("LINPUT2"),
366 SND_SOC_DAPM_INPUT("RINPUT2"),
367 SND_SOC_DAPM_INPUT("LINPUT3"),
368 SND_SOC_DAPM_INPUT("RINPUT3"),
369
370 SND_SOC_DAPM_SUPPLY("MICB", WM8960_POWER1, 1, 0, NULL, 0),
371
372 SND_SOC_DAPM_MIXER("Left Boost Mixer", WM8960_POWER1, 5, 0,
373 wm8960_lin_boost, ARRAY_SIZE(wm8960_lin_boost)),
374 SND_SOC_DAPM_MIXER("Right Boost Mixer", WM8960_POWER1, 4, 0,
375 wm8960_rin_boost, ARRAY_SIZE(wm8960_rin_boost)),
376
377 SND_SOC_DAPM_MIXER("Left Input Mixer", WM8960_POWER3, 5, 0,
378 wm8960_lin, ARRAY_SIZE(wm8960_lin)),
379 SND_SOC_DAPM_MIXER("Right Input Mixer", WM8960_POWER3, 4, 0,
380 wm8960_rin, ARRAY_SIZE(wm8960_rin)),
381
382 SND_SOC_DAPM_ADC("Left ADC", "Capture", WM8960_POWER1, 3, 0),
383 SND_SOC_DAPM_ADC("Right ADC", "Capture", WM8960_POWER1, 2, 0),
384
385 SND_SOC_DAPM_DAC("Left DAC", "Playback", WM8960_POWER2, 8, 0),
386 SND_SOC_DAPM_DAC("Right DAC", "Playback", WM8960_POWER2, 7, 0),
387
388 SND_SOC_DAPM_MIXER("Left Output Mixer", WM8960_POWER3, 3, 0,
389 &wm8960_loutput_mixer[0],
390 ARRAY_SIZE(wm8960_loutput_mixer)),
391 SND_SOC_DAPM_MIXER("Right Output Mixer", WM8960_POWER3, 2, 0,
392 &wm8960_routput_mixer[0],
393 ARRAY_SIZE(wm8960_routput_mixer)),
394
395 SND_SOC_DAPM_PGA("LOUT1 PGA", WM8960_POWER2, 6, 0, NULL, 0),
396 SND_SOC_DAPM_PGA("ROUT1 PGA", WM8960_POWER2, 5, 0, NULL, 0),
397
398 SND_SOC_DAPM_PGA("Left Speaker PGA", WM8960_POWER2, 4, 0, NULL, 0),
399 SND_SOC_DAPM_PGA("Right Speaker PGA", WM8960_POWER2, 3, 0, NULL, 0),
400
401 SND_SOC_DAPM_PGA("Right Speaker Output", WM8960_CLASSD1, 7, 0, NULL, 0),
402 SND_SOC_DAPM_PGA("Left Speaker Output", WM8960_CLASSD1, 6, 0, NULL, 0),
403
404 SND_SOC_DAPM_OUTPUT("SPK_LP"),
405 SND_SOC_DAPM_OUTPUT("SPK_LN"),
406 SND_SOC_DAPM_OUTPUT("HP_L"),
407 SND_SOC_DAPM_OUTPUT("HP_R"),
408 SND_SOC_DAPM_OUTPUT("SPK_RP"),
409 SND_SOC_DAPM_OUTPUT("SPK_RN"),
410 SND_SOC_DAPM_OUTPUT("OUT3"),
411 };
412
413 static const struct snd_soc_dapm_widget wm8960_dapm_widgets_out3[] = {
414 SND_SOC_DAPM_MIXER("Mono Output Mixer", WM8960_POWER2, 1, 0,
415 &wm8960_mono_out[0],
416 ARRAY_SIZE(wm8960_mono_out)),
417 };
418
419 /* Represent OUT3 as a PGA so that it gets turned on with LOUT1/ROUT1 */
420 static const struct snd_soc_dapm_widget wm8960_dapm_widgets_capless[] = {
421 SND_SOC_DAPM_PGA("OUT3 VMID", WM8960_POWER2, 1, 0, NULL, 0),
422 };
423
424 static const struct snd_soc_dapm_route audio_paths[] = {
425 { "Left Boost Mixer", "LINPUT1 Switch", "LINPUT1" },
426 { "Left Boost Mixer", "LINPUT2 Switch", "LINPUT2" },
427 { "Left Boost Mixer", "LINPUT3 Switch", "LINPUT3" },
428
429 { "Left Input Mixer", "Boost Switch", "Left Boost Mixer" },
430 { "Left Input Mixer", "Boost Switch", "LINPUT1" }, /* Really Boost Switch */
431 { "Left Input Mixer", NULL, "LINPUT2" },
432 { "Left Input Mixer", NULL, "LINPUT3" },
433
434 { "Right Boost Mixer", "RINPUT1 Switch", "RINPUT1" },
435 { "Right Boost Mixer", "RINPUT2 Switch", "RINPUT2" },
436 { "Right Boost Mixer", "RINPUT3 Switch", "RINPUT3" },
437
438 { "Right Input Mixer", "Boost Switch", "Right Boost Mixer" },
439 { "Right Input Mixer", "Boost Switch", "RINPUT1" }, /* Really Boost Switch */
440 { "Right Input Mixer", NULL, "RINPUT2" },
441 { "Right Input Mixer", NULL, "RINPUT3" },
442
443 { "Left ADC", NULL, "Left Input Mixer" },
444 { "Right ADC", NULL, "Right Input Mixer" },
445
446 { "Left Output Mixer", "LINPUT3 Switch", "LINPUT3" },
447 { "Left Output Mixer", "Boost Bypass Switch", "Left Boost Mixer" },
448 { "Left Output Mixer", "PCM Playback Switch", "Left DAC" },
449
450 { "Right Output Mixer", "RINPUT3 Switch", "RINPUT3" },
451 { "Right Output Mixer", "Boost Bypass Switch", "Right Boost Mixer" },
452 { "Right Output Mixer", "PCM Playback Switch", "Right DAC" },
453
454 { "LOUT1 PGA", NULL, "Left Output Mixer" },
455 { "ROUT1 PGA", NULL, "Right Output Mixer" },
456
457 { "HP_L", NULL, "LOUT1 PGA" },
458 { "HP_R", NULL, "ROUT1 PGA" },
459
460 { "Left Speaker PGA", NULL, "Left Output Mixer" },
461 { "Right Speaker PGA", NULL, "Right Output Mixer" },
462
463 { "Left Speaker Output", NULL, "Left Speaker PGA" },
464 { "Right Speaker Output", NULL, "Right Speaker PGA" },
465
466 { "SPK_LN", NULL, "Left Speaker Output" },
467 { "SPK_LP", NULL, "Left Speaker Output" },
468 { "SPK_RN", NULL, "Right Speaker Output" },
469 { "SPK_RP", NULL, "Right Speaker Output" },
470 };
471
472 static const struct snd_soc_dapm_route audio_paths_out3[] = {
473 { "Mono Output Mixer", "Left Switch", "Left Output Mixer" },
474 { "Mono Output Mixer", "Right Switch", "Right Output Mixer" },
475
476 { "OUT3", NULL, "Mono Output Mixer", }
477 };
478
479 static const struct snd_soc_dapm_route audio_paths_capless[] = {
480 { "HP_L", NULL, "OUT3 VMID" },
481 { "HP_R", NULL, "OUT3 VMID" },
482
483 { "OUT3 VMID", NULL, "Left Output Mixer" },
484 { "OUT3 VMID", NULL, "Right Output Mixer" },
485 };
486
wm8960_add_widgets(struct snd_soc_component * component)487 static int wm8960_add_widgets(struct snd_soc_component *component)
488 {
489 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
490 struct wm8960_data *pdata = &wm8960->pdata;
491 struct snd_soc_dapm_context *dapm = snd_soc_component_get_dapm(component);
492 struct snd_soc_dapm_widget *w;
493
494 snd_soc_dapm_new_controls(dapm, wm8960_dapm_widgets,
495 ARRAY_SIZE(wm8960_dapm_widgets));
496
497 snd_soc_dapm_add_routes(dapm, audio_paths, ARRAY_SIZE(audio_paths));
498
499 /* In capless mode OUT3 is used to provide VMID for the
500 * headphone outputs, otherwise it is used as a mono mixer.
501 */
502 if (pdata && pdata->capless) {
503 snd_soc_dapm_new_controls(dapm, wm8960_dapm_widgets_capless,
504 ARRAY_SIZE(wm8960_dapm_widgets_capless));
505
506 snd_soc_dapm_add_routes(dapm, audio_paths_capless,
507 ARRAY_SIZE(audio_paths_capless));
508 } else {
509 snd_soc_dapm_new_controls(dapm, wm8960_dapm_widgets_out3,
510 ARRAY_SIZE(wm8960_dapm_widgets_out3));
511
512 snd_soc_dapm_add_routes(dapm, audio_paths_out3,
513 ARRAY_SIZE(audio_paths_out3));
514 }
515
516 /* We need to power up the headphone output stage out of
517 * sequence for capless mode. To save scanning the widget
518 * list each time to find the desired power state do so now
519 * and save the result.
520 */
521 list_for_each_entry(w, &component->card->widgets, list) {
522 if (w->dapm != dapm)
523 continue;
524 if (strcmp(w->name, "LOUT1 PGA") == 0)
525 wm8960->lout1 = w;
526 if (strcmp(w->name, "ROUT1 PGA") == 0)
527 wm8960->rout1 = w;
528 if (strcmp(w->name, "OUT3 VMID") == 0)
529 wm8960->out3 = w;
530 }
531
532 return 0;
533 }
534
wm8960_set_dai_fmt(struct snd_soc_dai * codec_dai,unsigned int fmt)535 static int wm8960_set_dai_fmt(struct snd_soc_dai *codec_dai,
536 unsigned int fmt)
537 {
538 struct snd_soc_component *component = codec_dai->component;
539 u16 iface = 0;
540
541 /* set master/slave audio interface */
542 switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
543 case SND_SOC_DAIFMT_CBM_CFM:
544 iface |= 0x0040;
545 break;
546 case SND_SOC_DAIFMT_CBS_CFS:
547 break;
548 default:
549 return -EINVAL;
550 }
551
552 /* interface format */
553 switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
554 case SND_SOC_DAIFMT_I2S:
555 iface |= 0x0002;
556 break;
557 case SND_SOC_DAIFMT_RIGHT_J:
558 break;
559 case SND_SOC_DAIFMT_LEFT_J:
560 iface |= 0x0001;
561 break;
562 case SND_SOC_DAIFMT_DSP_A:
563 iface |= 0x0003;
564 break;
565 case SND_SOC_DAIFMT_DSP_B:
566 iface |= 0x0013;
567 break;
568 default:
569 return -EINVAL;
570 }
571
572 /* clock inversion */
573 switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
574 case SND_SOC_DAIFMT_NB_NF:
575 break;
576 case SND_SOC_DAIFMT_IB_IF:
577 iface |= 0x0090;
578 break;
579 case SND_SOC_DAIFMT_IB_NF:
580 iface |= 0x0080;
581 break;
582 case SND_SOC_DAIFMT_NB_IF:
583 iface |= 0x0010;
584 break;
585 default:
586 return -EINVAL;
587 }
588
589 /* set iface */
590 snd_soc_component_write(component, WM8960_IFACE1, iface);
591 return 0;
592 }
593
594 static struct {
595 int rate;
596 unsigned int val;
597 } alc_rates[] = {
598 { 48000, 0 },
599 { 44100, 0 },
600 { 32000, 1 },
601 { 22050, 2 },
602 { 24000, 2 },
603 { 16000, 3 },
604 { 11025, 4 },
605 { 12000, 4 },
606 { 8000, 5 },
607 };
608
609 /* -1 for reserved value */
610 static const int sysclk_divs[] = { 1, -1, 2, -1 };
611
612 /* Multiply 256 for internal 256 div */
613 static const int dac_divs[] = { 256, 384, 512, 768, 1024, 1408, 1536 };
614
615 /* Multiply 10 to eliminate decimials */
616 static const int bclk_divs[] = {
617 10, 15, 20, 30, 40, 55, 60, 80, 110,
618 120, 160, 220, 240, 320, 320, 320
619 };
620
621 /**
622 * wm8960_configure_sysclk - checks if there is a sysclk frequency available
623 * The sysclk must be chosen such that:
624 * - sysclk = MCLK / sysclk_divs
625 * - lrclk = sysclk / dac_divs
626 * - 10 * bclk = sysclk / bclk_divs
627 *
628 * @wm8960: codec private data
629 * @mclk: MCLK used to derive sysclk
630 * @sysclk_idx: sysclk_divs index for found sysclk
631 * @dac_idx: dac_divs index for found lrclk
632 * @bclk_idx: bclk_divs index for found bclk
633 *
634 * Returns:
635 * -1, in case no sysclk frequency available found
636 * >=0, in case we could derive bclk and lrclk from sysclk using
637 * (@sysclk_idx, @dac_idx, @bclk_idx) dividers
638 */
639 static
wm8960_configure_sysclk(struct wm8960_priv * wm8960,int mclk,int * sysclk_idx,int * dac_idx,int * bclk_idx)640 int wm8960_configure_sysclk(struct wm8960_priv *wm8960, int mclk,
641 int *sysclk_idx, int *dac_idx, int *bclk_idx)
642 {
643 int sysclk, bclk, lrclk;
644 int i, j, k;
645 int diff;
646
647 /* marker for no match */
648 *bclk_idx = -1;
649
650 bclk = wm8960->bclk;
651 lrclk = wm8960->lrclk;
652
653 /* check if the sysclk frequency is available. */
654 for (i = 0; i < ARRAY_SIZE(sysclk_divs); ++i) {
655 if (sysclk_divs[i] == -1)
656 continue;
657 sysclk = mclk / sysclk_divs[i];
658 for (j = 0; j < ARRAY_SIZE(dac_divs); ++j) {
659 if (sysclk != dac_divs[j] * lrclk)
660 continue;
661 for (k = 0; k < ARRAY_SIZE(bclk_divs); ++k) {
662 diff = sysclk - bclk * bclk_divs[k] / 10;
663 if (diff == 0) {
664 *sysclk_idx = i;
665 *dac_idx = j;
666 *bclk_idx = k;
667 break;
668 }
669 }
670 if (k != ARRAY_SIZE(bclk_divs))
671 break;
672 }
673 if (j != ARRAY_SIZE(dac_divs))
674 break;
675 }
676 return *bclk_idx;
677 }
678
679 /**
680 * wm8960_configure_pll - checks if there is a PLL out frequency available
681 * The PLL out frequency must be chosen such that:
682 * - sysclk = lrclk * dac_divs
683 * - freq_out = sysclk * sysclk_divs
684 * - 10 * sysclk = bclk * bclk_divs
685 *
686 * If we cannot find an exact match for (sysclk, lrclk, bclk)
687 * triplet, we relax the bclk such that bclk is chosen as the
688 * closest available frequency greater than expected bclk.
689 *
690 * @component: component structure
691 * @freq_in: input frequency used to derive freq out via PLL
692 * @sysclk_idx: sysclk_divs index for found sysclk
693 * @dac_idx: dac_divs index for found lrclk
694 * @bclk_idx: bclk_divs index for found bclk
695 *
696 * Returns:
697 * < 0, in case no PLL frequency out available was found
698 * >=0, in case we could derive bclk, lrclk, sysclk from PLL out using
699 * (@sysclk_idx, @dac_idx, @bclk_idx) dividers
700 */
701 static
wm8960_configure_pll(struct snd_soc_component * component,int freq_in,int * sysclk_idx,int * dac_idx,int * bclk_idx)702 int wm8960_configure_pll(struct snd_soc_component *component, int freq_in,
703 int *sysclk_idx, int *dac_idx, int *bclk_idx)
704 {
705 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
706 int sysclk, bclk, lrclk, freq_out;
707 int diff, closest, best_freq_out;
708 int i, j, k;
709
710 bclk = wm8960->bclk;
711 lrclk = wm8960->lrclk;
712 closest = freq_in;
713
714 best_freq_out = -EINVAL;
715 *sysclk_idx = *dac_idx = *bclk_idx = -1;
716
717 /*
718 * From Datasheet, the PLL performs best when f2 is between
719 * 90MHz and 100MHz, the desired sysclk output is 11.2896MHz
720 * or 12.288MHz, then sysclkdiv = 2 is the best choice.
721 * So search sysclk_divs from 2 to 1 other than from 1 to 2.
722 */
723 for (i = ARRAY_SIZE(sysclk_divs) - 1; i >= 0; --i) {
724 if (sysclk_divs[i] == -1)
725 continue;
726 for (j = 0; j < ARRAY_SIZE(dac_divs); ++j) {
727 sysclk = lrclk * dac_divs[j];
728 freq_out = sysclk * sysclk_divs[i];
729
730 for (k = 0; k < ARRAY_SIZE(bclk_divs); ++k) {
731 if (!is_pll_freq_available(freq_in, freq_out))
732 continue;
733
734 diff = sysclk - bclk * bclk_divs[k] / 10;
735 if (diff == 0) {
736 *sysclk_idx = i;
737 *dac_idx = j;
738 *bclk_idx = k;
739 return freq_out;
740 }
741 if (diff > 0 && closest > diff) {
742 *sysclk_idx = i;
743 *dac_idx = j;
744 *bclk_idx = k;
745 closest = diff;
746 best_freq_out = freq_out;
747 }
748 }
749 }
750 }
751
752 return best_freq_out;
753 }
wm8960_configure_clocking(struct snd_soc_component * component)754 static int wm8960_configure_clocking(struct snd_soc_component *component)
755 {
756 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
757 int freq_out, freq_in;
758 u16 iface1 = snd_soc_component_read(component, WM8960_IFACE1);
759 int i, j, k;
760 int ret;
761
762 /*
763 * For Slave mode clocking should still be configured,
764 * so this if statement should be removed, but some platform
765 * may not work if the sysclk is not configured, to avoid such
766 * compatible issue, just add '!wm8960->sysclk' condition in
767 * this if statement.
768 */
769 if (!(iface1 & (1 << 6)) && !wm8960->sysclk) {
770 dev_warn(component->dev,
771 "slave mode, but proceeding with no clock configuration\n");
772 return 0;
773 }
774
775 if (wm8960->clk_id != WM8960_SYSCLK_MCLK && !wm8960->freq_in) {
776 dev_err(component->dev, "No MCLK configured\n");
777 return -EINVAL;
778 }
779
780 freq_in = wm8960->freq_in;
781 /*
782 * If it's sysclk auto mode, check if the MCLK can provide sysclk or
783 * not. If MCLK can provide sysclk, using MCLK to provide sysclk
784 * directly. Otherwise, auto select a available pll out frequency
785 * and set PLL.
786 */
787 if (wm8960->clk_id == WM8960_SYSCLK_AUTO) {
788 /* disable the PLL and using MCLK to provide sysclk */
789 wm8960_set_pll(component, 0, 0);
790 freq_out = freq_in;
791 } else if (wm8960->sysclk) {
792 freq_out = wm8960->sysclk;
793 } else {
794 dev_err(component->dev, "No SYSCLK configured\n");
795 return -EINVAL;
796 }
797
798 if (wm8960->clk_id != WM8960_SYSCLK_PLL) {
799 ret = wm8960_configure_sysclk(wm8960, freq_out, &i, &j, &k);
800 if (ret >= 0) {
801 goto configure_clock;
802 } else if (wm8960->clk_id != WM8960_SYSCLK_AUTO) {
803 dev_err(component->dev, "failed to configure clock\n");
804 return -EINVAL;
805 }
806 }
807
808 freq_out = wm8960_configure_pll(component, freq_in, &i, &j, &k);
809 if (freq_out < 0) {
810 dev_err(component->dev, "failed to configure clock via PLL\n");
811 return freq_out;
812 }
813 wm8960_set_pll(component, freq_in, freq_out);
814
815 configure_clock:
816 /* configure sysclk clock */
817 snd_soc_component_update_bits(component, WM8960_CLOCK1, 3 << 1, i << 1);
818
819 /* configure frame clock */
820 snd_soc_component_update_bits(component, WM8960_CLOCK1, 0x7 << 3, j << 3);
821 snd_soc_component_update_bits(component, WM8960_CLOCK1, 0x7 << 6, j << 6);
822
823 /* configure bit clock */
824 snd_soc_component_update_bits(component, WM8960_CLOCK2, 0xf, k);
825
826 return 0;
827 }
828
wm8960_hw_params(struct snd_pcm_substream * substream,struct snd_pcm_hw_params * params,struct snd_soc_dai * dai)829 static int wm8960_hw_params(struct snd_pcm_substream *substream,
830 struct snd_pcm_hw_params *params,
831 struct snd_soc_dai *dai)
832 {
833 struct snd_soc_component *component = dai->component;
834 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
835 u16 iface = snd_soc_component_read(component, WM8960_IFACE1) & 0xfff3;
836 bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK;
837 int i;
838
839 wm8960->bclk = snd_soc_params_to_bclk(params);
840 if (params_channels(params) == 1)
841 wm8960->bclk *= 2;
842
843 /* bit size */
844 switch (params_width(params)) {
845 case 16:
846 break;
847 case 20:
848 iface |= 0x0004;
849 break;
850 case 24:
851 iface |= 0x0008;
852 break;
853 case 32:
854 /* right justify mode does not support 32 word length */
855 if ((iface & 0x3) != 0) {
856 iface |= 0x000c;
857 break;
858 }
859 fallthrough;
860 default:
861 dev_err(component->dev, "unsupported width %d\n",
862 params_width(params));
863 return -EINVAL;
864 }
865
866 wm8960->lrclk = params_rate(params);
867 /* Update filters for the new rate */
868 if (tx) {
869 wm8960_set_deemph(component);
870 } else {
871 for (i = 0; i < ARRAY_SIZE(alc_rates); i++)
872 if (alc_rates[i].rate == params_rate(params))
873 snd_soc_component_update_bits(component,
874 WM8960_ADDCTL3, 0x7,
875 alc_rates[i].val);
876 }
877
878 /* set iface */
879 snd_soc_component_write(component, WM8960_IFACE1, iface);
880
881 wm8960->is_stream_in_use[tx] = true;
882
883 if (!wm8960->is_stream_in_use[!tx])
884 return wm8960_configure_clocking(component);
885
886 return 0;
887 }
888
wm8960_hw_free(struct snd_pcm_substream * substream,struct snd_soc_dai * dai)889 static int wm8960_hw_free(struct snd_pcm_substream *substream,
890 struct snd_soc_dai *dai)
891 {
892 struct snd_soc_component *component = dai->component;
893 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
894 bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK;
895
896 wm8960->is_stream_in_use[tx] = false;
897
898 return 0;
899 }
900
wm8960_mute(struct snd_soc_dai * dai,int mute,int direction)901 static int wm8960_mute(struct snd_soc_dai *dai, int mute, int direction)
902 {
903 struct snd_soc_component *component = dai->component;
904
905 if (mute)
906 snd_soc_component_update_bits(component, WM8960_DACCTL1, 0x8, 0x8);
907 else
908 snd_soc_component_update_bits(component, WM8960_DACCTL1, 0x8, 0);
909 return 0;
910 }
911
wm8960_set_bias_level_out3(struct snd_soc_component * component,enum snd_soc_bias_level level)912 static int wm8960_set_bias_level_out3(struct snd_soc_component *component,
913 enum snd_soc_bias_level level)
914 {
915 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
916 u16 pm2 = snd_soc_component_read(component, WM8960_POWER2);
917 int ret;
918 ktime_t tout;
919
920 switch (level) {
921 case SND_SOC_BIAS_ON:
922 break;
923
924 case SND_SOC_BIAS_PREPARE:
925 switch (snd_soc_component_get_bias_level(component)) {
926 case SND_SOC_BIAS_STANDBY:
927 if (!IS_ERR(wm8960->mclk)) {
928 ret = clk_prepare_enable(wm8960->mclk);
929 if (ret) {
930 dev_err(component->dev,
931 "Failed to enable MCLK: %d\n",
932 ret);
933 return ret;
934 }
935 }
936
937 ret = wm8960_configure_clocking(component);
938 if (ret)
939 return ret;
940
941 /* Set VMID to 2x50k */
942 snd_soc_component_update_bits(component, WM8960_POWER1, 0x180, 0x80);
943 break;
944
945 case SND_SOC_BIAS_ON:
946 /*
947 * If it's sysclk auto mode, and the pll is enabled,
948 * disable the pll
949 */
950 if (wm8960->clk_id == WM8960_SYSCLK_AUTO && (pm2 & 0x1))
951 wm8960_set_pll(component, 0, 0);
952
953 if (!IS_ERR(wm8960->mclk))
954 clk_disable_unprepare(wm8960->mclk);
955 break;
956
957 default:
958 break;
959 }
960
961 break;
962
963 case SND_SOC_BIAS_STANDBY:
964 if (snd_soc_component_get_bias_level(component) == SND_SOC_BIAS_OFF) {
965 /* ensure discharge is complete */
966 tout = WM8960_DSCH_TOUT - ktime_ms_delta(ktime_get(), wm8960->dsch_start);
967 if (tout > 0)
968 msleep(tout);
969
970 regcache_sync(wm8960->regmap);
971
972 /* Enable anti-pop features */
973 snd_soc_component_write(component, WM8960_APOP1,
974 WM8960_POBCTRL | WM8960_SOFT_ST |
975 WM8960_BUFDCOPEN | WM8960_BUFIOEN);
976
977 /* Enable & ramp VMID at 2x50k */
978 snd_soc_component_update_bits(component, WM8960_POWER1, 0x80, 0x80);
979 msleep(100);
980
981 /* Enable VREF */
982 snd_soc_component_update_bits(component, WM8960_POWER1, WM8960_VREF,
983 WM8960_VREF);
984
985 /* Disable anti-pop features */
986 snd_soc_component_write(component, WM8960_APOP1, WM8960_BUFIOEN);
987 }
988
989 /* Set VMID to 2x250k */
990 snd_soc_component_update_bits(component, WM8960_POWER1, 0x180, 0x100);
991 break;
992
993 case SND_SOC_BIAS_OFF:
994 /* Enable anti-pop features */
995 snd_soc_component_write(component, WM8960_APOP1,
996 WM8960_POBCTRL | WM8960_SOFT_ST |
997 WM8960_BUFDCOPEN | WM8960_BUFIOEN);
998
999 /* Disable VMID and VREF, mark discharge */
1000 snd_soc_component_write(component, WM8960_POWER1, 0);
1001 wm8960->dsch_start = ktime_get();
1002 break;
1003 }
1004
1005 return 0;
1006 }
1007
wm8960_set_bias_level_capless(struct snd_soc_component * component,enum snd_soc_bias_level level)1008 static int wm8960_set_bias_level_capless(struct snd_soc_component *component,
1009 enum snd_soc_bias_level level)
1010 {
1011 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
1012 u16 pm2 = snd_soc_component_read(component, WM8960_POWER2);
1013 int reg, ret;
1014
1015 switch (level) {
1016 case SND_SOC_BIAS_ON:
1017 break;
1018
1019 case SND_SOC_BIAS_PREPARE:
1020 switch (snd_soc_component_get_bias_level(component)) {
1021 case SND_SOC_BIAS_STANDBY:
1022 /* Enable anti pop mode */
1023 snd_soc_component_update_bits(component, WM8960_APOP1,
1024 WM8960_POBCTRL | WM8960_SOFT_ST |
1025 WM8960_BUFDCOPEN,
1026 WM8960_POBCTRL | WM8960_SOFT_ST |
1027 WM8960_BUFDCOPEN);
1028
1029 /* Enable LOUT1, ROUT1 and OUT3 if they're enabled */
1030 reg = 0;
1031 if (wm8960->lout1 && wm8960->lout1->power)
1032 reg |= WM8960_PWR2_LOUT1;
1033 if (wm8960->rout1 && wm8960->rout1->power)
1034 reg |= WM8960_PWR2_ROUT1;
1035 if (wm8960->out3 && wm8960->out3->power)
1036 reg |= WM8960_PWR2_OUT3;
1037 snd_soc_component_update_bits(component, WM8960_POWER2,
1038 WM8960_PWR2_LOUT1 |
1039 WM8960_PWR2_ROUT1 |
1040 WM8960_PWR2_OUT3, reg);
1041
1042 /* Enable VMID at 2*50k */
1043 snd_soc_component_update_bits(component, WM8960_POWER1,
1044 WM8960_VMID_MASK, 0x80);
1045
1046 /* Ramp */
1047 msleep(100);
1048
1049 /* Enable VREF */
1050 snd_soc_component_update_bits(component, WM8960_POWER1,
1051 WM8960_VREF, WM8960_VREF);
1052
1053 msleep(100);
1054
1055 if (!IS_ERR(wm8960->mclk)) {
1056 ret = clk_prepare_enable(wm8960->mclk);
1057 if (ret) {
1058 dev_err(component->dev,
1059 "Failed to enable MCLK: %d\n",
1060 ret);
1061 return ret;
1062 }
1063 }
1064
1065 ret = wm8960_configure_clocking(component);
1066 if (ret)
1067 return ret;
1068
1069 break;
1070
1071 case SND_SOC_BIAS_ON:
1072 /*
1073 * If it's sysclk auto mode, and the pll is enabled,
1074 * disable the pll
1075 */
1076 if (wm8960->clk_id == WM8960_SYSCLK_AUTO && (pm2 & 0x1))
1077 wm8960_set_pll(component, 0, 0);
1078
1079 if (!IS_ERR(wm8960->mclk))
1080 clk_disable_unprepare(wm8960->mclk);
1081
1082 /* Enable anti-pop mode */
1083 snd_soc_component_update_bits(component, WM8960_APOP1,
1084 WM8960_POBCTRL | WM8960_SOFT_ST |
1085 WM8960_BUFDCOPEN,
1086 WM8960_POBCTRL | WM8960_SOFT_ST |
1087 WM8960_BUFDCOPEN);
1088
1089 /* Disable VMID and VREF */
1090 snd_soc_component_update_bits(component, WM8960_POWER1,
1091 WM8960_VREF | WM8960_VMID_MASK, 0);
1092 break;
1093
1094 case SND_SOC_BIAS_OFF:
1095 regcache_sync(wm8960->regmap);
1096 break;
1097 default:
1098 break;
1099 }
1100 break;
1101
1102 case SND_SOC_BIAS_STANDBY:
1103 switch (snd_soc_component_get_bias_level(component)) {
1104 case SND_SOC_BIAS_PREPARE:
1105 /* Disable HP discharge */
1106 snd_soc_component_update_bits(component, WM8960_APOP2,
1107 WM8960_DISOP | WM8960_DRES_MASK,
1108 0);
1109
1110 /* Disable anti-pop features */
1111 snd_soc_component_update_bits(component, WM8960_APOP1,
1112 WM8960_POBCTRL | WM8960_SOFT_ST |
1113 WM8960_BUFDCOPEN,
1114 WM8960_POBCTRL | WM8960_SOFT_ST |
1115 WM8960_BUFDCOPEN);
1116 break;
1117
1118 default:
1119 break;
1120 }
1121 break;
1122
1123 case SND_SOC_BIAS_OFF:
1124 break;
1125 }
1126
1127 return 0;
1128 }
1129
1130 /* PLL divisors */
1131 struct _pll_div {
1132 u32 pre_div:1;
1133 u32 n:4;
1134 u32 k:24;
1135 };
1136
is_pll_freq_available(unsigned int source,unsigned int target)1137 static bool is_pll_freq_available(unsigned int source, unsigned int target)
1138 {
1139 unsigned int Ndiv;
1140
1141 if (source == 0 || target == 0)
1142 return false;
1143
1144 /* Scale up target to PLL operating frequency */
1145 target *= 4;
1146 Ndiv = target / source;
1147
1148 if (Ndiv < 6) {
1149 source >>= 1;
1150 Ndiv = target / source;
1151 }
1152
1153 if ((Ndiv < 6) || (Ndiv > 12))
1154 return false;
1155
1156 return true;
1157 }
1158
1159 /* The size in bits of the pll divide multiplied by 10
1160 * to allow rounding later */
1161 #define FIXED_PLL_SIZE ((1 << 24) * 10)
1162
pll_factors(unsigned int source,unsigned int target,struct _pll_div * pll_div)1163 static int pll_factors(unsigned int source, unsigned int target,
1164 struct _pll_div *pll_div)
1165 {
1166 unsigned long long Kpart;
1167 unsigned int K, Ndiv, Nmod;
1168
1169 pr_debug("WM8960 PLL: setting %dHz->%dHz\n", source, target);
1170
1171 /* Scale up target to PLL operating frequency */
1172 target *= 4;
1173
1174 Ndiv = target / source;
1175 if (Ndiv < 6) {
1176 source >>= 1;
1177 pll_div->pre_div = 1;
1178 Ndiv = target / source;
1179 } else
1180 pll_div->pre_div = 0;
1181
1182 if ((Ndiv < 6) || (Ndiv > 12)) {
1183 pr_err("WM8960 PLL: Unsupported N=%d\n", Ndiv);
1184 return -EINVAL;
1185 }
1186
1187 pll_div->n = Ndiv;
1188 Nmod = target % source;
1189 Kpart = FIXED_PLL_SIZE * (long long)Nmod;
1190
1191 do_div(Kpart, source);
1192
1193 K = Kpart & 0xFFFFFFFF;
1194
1195 /* Check if we need to round */
1196 if ((K % 10) >= 5)
1197 K += 5;
1198
1199 /* Move down to proper range now rounding is done */
1200 K /= 10;
1201
1202 pll_div->k = K;
1203
1204 pr_debug("WM8960 PLL: N=%x K=%x pre_div=%d\n",
1205 pll_div->n, pll_div->k, pll_div->pre_div);
1206
1207 return 0;
1208 }
1209
wm8960_set_pll(struct snd_soc_component * component,unsigned int freq_in,unsigned int freq_out)1210 static int wm8960_set_pll(struct snd_soc_component *component,
1211 unsigned int freq_in, unsigned int freq_out)
1212 {
1213 u16 reg;
1214 static struct _pll_div pll_div;
1215 int ret;
1216
1217 if (freq_in && freq_out) {
1218 ret = pll_factors(freq_in, freq_out, &pll_div);
1219 if (ret != 0)
1220 return ret;
1221 }
1222
1223 /* Disable the PLL: even if we are changing the frequency the
1224 * PLL needs to be disabled while we do so. */
1225 snd_soc_component_update_bits(component, WM8960_CLOCK1, 0x1, 0);
1226 snd_soc_component_update_bits(component, WM8960_POWER2, 0x1, 0);
1227
1228 if (!freq_in || !freq_out)
1229 return 0;
1230
1231 reg = snd_soc_component_read(component, WM8960_PLL1) & ~0x3f;
1232 reg |= pll_div.pre_div << 4;
1233 reg |= pll_div.n;
1234
1235 if (pll_div.k) {
1236 reg |= 0x20;
1237
1238 snd_soc_component_write(component, WM8960_PLL2, (pll_div.k >> 16) & 0xff);
1239 snd_soc_component_write(component, WM8960_PLL3, (pll_div.k >> 8) & 0xff);
1240 snd_soc_component_write(component, WM8960_PLL4, pll_div.k & 0xff);
1241 }
1242 snd_soc_component_write(component, WM8960_PLL1, reg);
1243
1244 /* Turn it on */
1245 snd_soc_component_update_bits(component, WM8960_POWER2, 0x1, 0x1);
1246 msleep(250);
1247 snd_soc_component_update_bits(component, WM8960_CLOCK1, 0x1, 0x1);
1248
1249 return 0;
1250 }
1251
wm8960_set_dai_pll(struct snd_soc_dai * codec_dai,int pll_id,int source,unsigned int freq_in,unsigned int freq_out)1252 static int wm8960_set_dai_pll(struct snd_soc_dai *codec_dai, int pll_id,
1253 int source, unsigned int freq_in, unsigned int freq_out)
1254 {
1255 struct snd_soc_component *component = codec_dai->component;
1256 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
1257
1258 wm8960->freq_in = freq_in;
1259
1260 if (pll_id == WM8960_SYSCLK_AUTO)
1261 return 0;
1262
1263 return wm8960_set_pll(component, freq_in, freq_out);
1264 }
1265
wm8960_set_dai_clkdiv(struct snd_soc_dai * codec_dai,int div_id,int div)1266 static int wm8960_set_dai_clkdiv(struct snd_soc_dai *codec_dai,
1267 int div_id, int div)
1268 {
1269 struct snd_soc_component *component = codec_dai->component;
1270 u16 reg;
1271
1272 switch (div_id) {
1273 case WM8960_SYSCLKDIV:
1274 reg = snd_soc_component_read(component, WM8960_CLOCK1) & 0x1f9;
1275 snd_soc_component_write(component, WM8960_CLOCK1, reg | div);
1276 break;
1277 case WM8960_DACDIV:
1278 reg = snd_soc_component_read(component, WM8960_CLOCK1) & 0x1c7;
1279 snd_soc_component_write(component, WM8960_CLOCK1, reg | div);
1280 break;
1281 case WM8960_OPCLKDIV:
1282 reg = snd_soc_component_read(component, WM8960_PLL1) & 0x03f;
1283 snd_soc_component_write(component, WM8960_PLL1, reg | div);
1284 break;
1285 case WM8960_DCLKDIV:
1286 reg = snd_soc_component_read(component, WM8960_CLOCK2) & 0x03f;
1287 snd_soc_component_write(component, WM8960_CLOCK2, reg | div);
1288 break;
1289 case WM8960_TOCLKSEL:
1290 reg = snd_soc_component_read(component, WM8960_ADDCTL1) & 0x1fd;
1291 snd_soc_component_write(component, WM8960_ADDCTL1, reg | div);
1292 break;
1293 default:
1294 return -EINVAL;
1295 }
1296
1297 return 0;
1298 }
1299
wm8960_set_bias_level(struct snd_soc_component * component,enum snd_soc_bias_level level)1300 static int wm8960_set_bias_level(struct snd_soc_component *component,
1301 enum snd_soc_bias_level level)
1302 {
1303 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
1304
1305 return wm8960->set_bias_level(component, level);
1306 }
1307
wm8960_set_dai_sysclk(struct snd_soc_dai * dai,int clk_id,unsigned int freq,int dir)1308 static int wm8960_set_dai_sysclk(struct snd_soc_dai *dai, int clk_id,
1309 unsigned int freq, int dir)
1310 {
1311 struct snd_soc_component *component = dai->component;
1312 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
1313
1314 switch (clk_id) {
1315 case WM8960_SYSCLK_MCLK:
1316 snd_soc_component_update_bits(component, WM8960_CLOCK1,
1317 0x1, WM8960_SYSCLK_MCLK);
1318 break;
1319 case WM8960_SYSCLK_PLL:
1320 snd_soc_component_update_bits(component, WM8960_CLOCK1,
1321 0x1, WM8960_SYSCLK_PLL);
1322 break;
1323 case WM8960_SYSCLK_AUTO:
1324 break;
1325 default:
1326 return -EINVAL;
1327 }
1328
1329 wm8960->sysclk = freq;
1330 wm8960->clk_id = clk_id;
1331
1332 return 0;
1333 }
1334
1335 #define WM8960_RATES SNDRV_PCM_RATE_8000_48000
1336
1337 #define WM8960_FORMATS \
1338 (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE | \
1339 SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE)
1340
1341 static const struct snd_soc_dai_ops wm8960_dai_ops = {
1342 .hw_params = wm8960_hw_params,
1343 .hw_free = wm8960_hw_free,
1344 .mute_stream = wm8960_mute,
1345 .set_fmt = wm8960_set_dai_fmt,
1346 .set_clkdiv = wm8960_set_dai_clkdiv,
1347 .set_pll = wm8960_set_dai_pll,
1348 .set_sysclk = wm8960_set_dai_sysclk,
1349 .no_capture_mute = 1,
1350 };
1351
1352 static struct snd_soc_dai_driver wm8960_dai = {
1353 .name = "wm8960-hifi",
1354 .playback = {
1355 .stream_name = "Playback",
1356 .channels_min = 1,
1357 .channels_max = 2,
1358 .rates = WM8960_RATES,
1359 .formats = WM8960_FORMATS,},
1360 .capture = {
1361 .stream_name = "Capture",
1362 .channels_min = 1,
1363 .channels_max = 2,
1364 .rates = WM8960_RATES,
1365 .formats = WM8960_FORMATS,},
1366 .ops = &wm8960_dai_ops,
1367 .symmetric_rate = 1,
1368 };
1369
wm8960_probe(struct snd_soc_component * component)1370 static int wm8960_probe(struct snd_soc_component *component)
1371 {
1372 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component);
1373 struct wm8960_data *pdata = &wm8960->pdata;
1374
1375 if (pdata->capless)
1376 wm8960->set_bias_level = wm8960_set_bias_level_capless;
1377 else
1378 wm8960->set_bias_level = wm8960_set_bias_level_out3;
1379
1380 snd_soc_add_component_controls(component, wm8960_snd_controls,
1381 ARRAY_SIZE(wm8960_snd_controls));
1382 wm8960_add_widgets(component);
1383
1384 return 0;
1385 }
1386
1387 static const struct snd_soc_component_driver soc_component_dev_wm8960 = {
1388 .probe = wm8960_probe,
1389 .set_bias_level = wm8960_set_bias_level,
1390 .suspend_bias_off = 1,
1391 .idle_bias_on = 1,
1392 .use_pmdown_time = 1,
1393 .endianness = 1,
1394 };
1395
1396 static const struct regmap_config wm8960_regmap = {
1397 .reg_bits = 7,
1398 .val_bits = 9,
1399 .max_register = WM8960_PLL4,
1400
1401 .reg_defaults = wm8960_reg_defaults,
1402 .num_reg_defaults = ARRAY_SIZE(wm8960_reg_defaults),
1403 .cache_type = REGCACHE_MAPLE,
1404
1405 .volatile_reg = wm8960_volatile,
1406 };
1407
wm8960_set_pdata_from_of(struct i2c_client * i2c,struct wm8960_data * pdata)1408 static void wm8960_set_pdata_from_of(struct i2c_client *i2c,
1409 struct wm8960_data *pdata)
1410 {
1411 const struct device_node *np = i2c->dev.of_node;
1412
1413 if (of_property_read_bool(np, "wlf,capless"))
1414 pdata->capless = true;
1415
1416 if (of_property_read_bool(np, "wlf,shared-lrclk"))
1417 pdata->shared_lrclk = true;
1418
1419 of_property_read_u32_array(np, "wlf,gpio-cfg", pdata->gpio_cfg,
1420 ARRAY_SIZE(pdata->gpio_cfg));
1421
1422 of_property_read_u32_array(np, "wlf,hp-cfg", pdata->hp_cfg,
1423 ARRAY_SIZE(pdata->hp_cfg));
1424 }
1425
wm8960_i2c_probe(struct i2c_client * i2c)1426 static int wm8960_i2c_probe(struct i2c_client *i2c)
1427 {
1428 struct wm8960_data *pdata = dev_get_platdata(&i2c->dev);
1429 struct wm8960_priv *wm8960;
1430 unsigned int i;
1431 int ret;
1432 u8 val;
1433
1434 wm8960 = devm_kzalloc(&i2c->dev, sizeof(struct wm8960_priv),
1435 GFP_KERNEL);
1436 if (wm8960 == NULL)
1437 return -ENOMEM;
1438
1439 wm8960->mclk = devm_clk_get(&i2c->dev, "mclk");
1440 if (IS_ERR(wm8960->mclk)) {
1441 if (PTR_ERR(wm8960->mclk) == -EPROBE_DEFER)
1442 return -EPROBE_DEFER;
1443 } else {
1444 ret = clk_get_rate(wm8960->mclk);
1445 if (ret >= 0) {
1446 wm8960->freq_in = ret;
1447 } else {
1448 dev_err(&i2c->dev, "Failed to read MCLK rate: %d\n",
1449 ret);
1450 }
1451 }
1452
1453 for (i = 0; i < ARRAY_SIZE(wm8960->supplies); i++)
1454 wm8960->supplies[i].supply = wm8960_supply_names[i];
1455
1456 ret = devm_regulator_bulk_get(&i2c->dev, ARRAY_SIZE(wm8960->supplies),
1457 wm8960->supplies);
1458 if (ret < 0) {
1459 dev_err(&i2c->dev, "Failed to request supplies: %d\n", ret);
1460 return ret;
1461 }
1462
1463 ret = regulator_bulk_enable(ARRAY_SIZE(wm8960->supplies),
1464 wm8960->supplies);
1465 if (ret < 0) {
1466 dev_err(&i2c->dev, "Failed to enable supplies: %d\n", ret);
1467 return ret;
1468 }
1469
1470 wm8960->regmap = devm_regmap_init_i2c(i2c, &wm8960_regmap);
1471 if (IS_ERR(wm8960->regmap)) {
1472 ret = PTR_ERR(wm8960->regmap);
1473 goto bulk_disable;
1474 }
1475
1476 if (pdata)
1477 memcpy(&wm8960->pdata, pdata, sizeof(struct wm8960_data));
1478 else if (i2c->dev.of_node)
1479 wm8960_set_pdata_from_of(i2c, &wm8960->pdata);
1480
1481 ret = i2c_master_recv(i2c, &val, sizeof(val));
1482 if (ret >= 0) {
1483 dev_err(&i2c->dev, "Not wm8960, wm8960 reg can not read by i2c\n");
1484 ret = -EINVAL;
1485 goto bulk_disable;
1486 }
1487
1488 ret = wm8960_reset(wm8960->regmap);
1489 if (ret != 0) {
1490 dev_err(&i2c->dev, "Failed to issue reset\n");
1491 goto bulk_disable;
1492 }
1493
1494 if (wm8960->pdata.shared_lrclk) {
1495 ret = regmap_update_bits(wm8960->regmap, WM8960_ADDCTL2,
1496 0x4, 0x4);
1497 if (ret != 0) {
1498 dev_err(&i2c->dev, "Failed to enable LRCM: %d\n",
1499 ret);
1500 goto bulk_disable;
1501 }
1502 }
1503
1504 /* Latch the update bits */
1505 regmap_update_bits(wm8960->regmap, WM8960_LINVOL, 0x100, 0x100);
1506 regmap_update_bits(wm8960->regmap, WM8960_RINVOL, 0x100, 0x100);
1507 regmap_update_bits(wm8960->regmap, WM8960_LADC, 0x100, 0x100);
1508 regmap_update_bits(wm8960->regmap, WM8960_RADC, 0x100, 0x100);
1509 regmap_update_bits(wm8960->regmap, WM8960_LDAC, 0x100, 0x100);
1510 regmap_update_bits(wm8960->regmap, WM8960_RDAC, 0x100, 0x100);
1511 regmap_update_bits(wm8960->regmap, WM8960_LOUT1, 0x100, 0x100);
1512 regmap_update_bits(wm8960->regmap, WM8960_ROUT1, 0x100, 0x100);
1513 regmap_update_bits(wm8960->regmap, WM8960_LOUT2, 0x100, 0x100);
1514 regmap_update_bits(wm8960->regmap, WM8960_ROUT2, 0x100, 0x100);
1515
1516 /* ADCLRC pin configured as GPIO. */
1517 regmap_update_bits(wm8960->regmap, WM8960_IFACE2, 1 << 6,
1518 wm8960->pdata.gpio_cfg[0] << 6);
1519 regmap_update_bits(wm8960->regmap, WM8960_ADDCTL4, 0xF << 4,
1520 wm8960->pdata.gpio_cfg[1] << 4);
1521
1522 /* Enable headphone jack detect */
1523 regmap_update_bits(wm8960->regmap, WM8960_ADDCTL4, 3 << 2,
1524 wm8960->pdata.hp_cfg[0] << 2);
1525 regmap_update_bits(wm8960->regmap, WM8960_ADDCTL2, 3 << 5,
1526 wm8960->pdata.hp_cfg[1] << 5);
1527 regmap_update_bits(wm8960->regmap, WM8960_ADDCTL1, 3,
1528 wm8960->pdata.hp_cfg[2]);
1529
1530 i2c_set_clientdata(i2c, wm8960);
1531
1532 ret = devm_snd_soc_register_component(&i2c->dev,
1533 &soc_component_dev_wm8960, &wm8960_dai, 1);
1534 if (ret)
1535 goto bulk_disable;
1536
1537 return 0;
1538
1539 bulk_disable:
1540 regulator_bulk_disable(ARRAY_SIZE(wm8960->supplies), wm8960->supplies);
1541 return ret;
1542 }
1543
wm8960_i2c_remove(struct i2c_client * client)1544 static void wm8960_i2c_remove(struct i2c_client *client)
1545 {
1546 struct wm8960_priv *wm8960 = i2c_get_clientdata(client);
1547
1548 regulator_bulk_disable(ARRAY_SIZE(wm8960->supplies), wm8960->supplies);
1549 }
1550
1551 static const struct i2c_device_id wm8960_i2c_id[] = {
1552 { "wm8960" },
1553 { }
1554 };
1555 MODULE_DEVICE_TABLE(i2c, wm8960_i2c_id);
1556
1557 #if defined(CONFIG_OF)
1558 static const struct of_device_id wm8960_of_match[] = {
1559 { .compatible = "wlf,wm8960", },
1560 { }
1561 };
1562 MODULE_DEVICE_TABLE(of, wm8960_of_match);
1563 #endif
1564
1565 #if defined(CONFIG_ACPI)
1566 static const struct acpi_device_id wm8960_acpi_match[] = {
1567 { "1AEC8960", 0 }, /* Wolfson PCI ID + part ID */
1568 { "10138960", 0 }, /* Cirrus Logic PCI ID + part ID */
1569 { },
1570 };
1571 MODULE_DEVICE_TABLE(acpi, wm8960_acpi_match);
1572 #endif
1573
1574 static struct i2c_driver wm8960_i2c_driver = {
1575 .driver = {
1576 .name = "wm8960",
1577 .of_match_table = of_match_ptr(wm8960_of_match),
1578 .acpi_match_table = ACPI_PTR(wm8960_acpi_match),
1579 },
1580 .probe = wm8960_i2c_probe,
1581 .remove = wm8960_i2c_remove,
1582 .id_table = wm8960_i2c_id,
1583 };
1584
1585 module_i2c_driver(wm8960_i2c_driver);
1586
1587 MODULE_DESCRIPTION("ASoC WM8960 driver");
1588 MODULE_AUTHOR("Liam Girdwood");
1589 MODULE_LICENSE("GPL");
1590