1 /*
2 * 3c595.c -- 3COM 3C595 Fast Etherlink III PCI driver for etherboot
3 *
4 * Copyright (C) 2000 Shusuke Nisiyama <shu@athena.qe.eng.hokudai.ac.jp>
5 * All rights reserved.
6 * Mar. 14, 2000
7 *
8 * This software may be used, modified, copied, distributed, and sold, in
9 * both source and binary form provided that the above copyright and these
10 * terms are retained. Under no circumstances are the authors responsible for
11 * the proper functioning of this software, nor do the authors assume any
12 * responsibility for damages incurred with its use.
13 *
14 * This code is based on Martin Renters' etherboot-4.4.3 3c509.c and
15 * Herb Peyerl's FreeBSD 3.4-RELEASE if_vx.c driver.
16 *
17 * Copyright (C) 1993-1994, David Greenman, Martin Renters.
18 * Copyright (C) 1993-1995, Andres Vega Garcia.
19 * Copyright (C) 1995, Serge Babkin.
20 *
21 * Copyright (c) 1994 Herb Peyerl <hpeyerl@novatel.ca>
22 *
23 * timlegge 08-24-2003 Add Multicast Support
24 */
25
26 /* #define EDEBUG */
27
28 #include "etherboot.h"
29 #include "nic.h"
30 #include "pci.h"
31 #include "3c595.h"
32 #include "timer.h"
33
34 static unsigned short eth_nic_base;
35 static unsigned short vx_connector, vx_connectors;
36
37 static struct connector_entry {
38 int bit;
39 char *name;
40 } conn_tab[VX_CONNECTORS] = {
41 #define CONNECTOR_UTP 0
42 { 0x08, "utp"},
43 #define CONNECTOR_AUI 1
44 { 0x20, "aui"},
45 /* dummy */
46 { 0, "???"},
47 #define CONNECTOR_BNC 3
48 { 0x10, "bnc"},
49 #define CONNECTOR_TX 4
50 { 0x02, "tx"},
51 #define CONNECTOR_FX 5
52 { 0x04, "fx"},
53 #define CONNECTOR_MII 6
54 { 0x40, "mii"},
55 { 0, "???"}
56 };
57
58 static void vxgetlink(void);
59 static void vxsetlink(void);
60
61 /**************************************************************************
62 ETH_RESET - Reset adapter
63 ***************************************************************************/
t595_reset(struct nic * nic)64 static void t595_reset(struct nic *nic)
65 {
66 int i;
67
68 /***********************************************************
69 Reset 3Com 595 card
70 *************************************************************/
71
72 /* stop card */
73 outw(RX_DISABLE, BASE + VX_COMMAND);
74 outw(RX_DISCARD_TOP_PACK, BASE + VX_COMMAND);
75 VX_BUSY_WAIT;
76 outw(TX_DISABLE, BASE + VX_COMMAND);
77 outw(STOP_TRANSCEIVER, BASE + VX_COMMAND);
78 udelay(8000);
79 outw(RX_RESET, BASE + VX_COMMAND);
80 VX_BUSY_WAIT;
81 outw(TX_RESET, BASE + VX_COMMAND);
82 VX_BUSY_WAIT;
83 outw(C_INTR_LATCH, BASE + VX_COMMAND);
84 outw(SET_RD_0_MASK, BASE + VX_COMMAND);
85 outw(SET_INTR_MASK, BASE + VX_COMMAND);
86 outw(SET_RX_FILTER, BASE + VX_COMMAND);
87
88 /*
89 * initialize card
90 */
91 VX_BUSY_WAIT;
92
93 GO_WINDOW(0);
94
95 /* Disable the card */
96 /* outw(0, BASE + VX_W0_CONFIG_CTRL); */
97
98 /* Configure IRQ to none */
99 /* outw(SET_IRQ(0), BASE + VX_W0_RESOURCE_CFG); */
100
101 /* Enable the card */
102 /* outw(ENABLE_DRQ_IRQ, BASE + VX_W0_CONFIG_CTRL); */
103
104 GO_WINDOW(2);
105
106 /* Reload the ether_addr. */
107 for (i = 0; i < ETH_ALEN; i++)
108 outb(nic->node_addr[i], BASE + VX_W2_ADDR_0 + i);
109
110 outw(RX_RESET, BASE + VX_COMMAND);
111 VX_BUSY_WAIT;
112 outw(TX_RESET, BASE + VX_COMMAND);
113 VX_BUSY_WAIT;
114
115 /* Window 1 is operating window */
116 GO_WINDOW(1);
117 for (i = 0; i < 31; i++)
118 inb(BASE + VX_W1_TX_STATUS);
119
120 outw(SET_RD_0_MASK | S_CARD_FAILURE | S_RX_COMPLETE |
121 S_TX_COMPLETE | S_TX_AVAIL, BASE + VX_COMMAND);
122 outw(SET_INTR_MASK | S_CARD_FAILURE | S_RX_COMPLETE |
123 S_TX_COMPLETE | S_TX_AVAIL, BASE + VX_COMMAND);
124
125 /*
126 * Attempt to get rid of any stray interrupts that occured during
127 * configuration. On the i386 this isn't possible because one may
128 * already be queued. However, a single stray interrupt is
129 * unimportant.
130 */
131
132 outw(ACK_INTR | 0xff, BASE + VX_COMMAND);
133
134 outw(SET_RX_FILTER | FIL_INDIVIDUAL |
135 FIL_BRDCST|FIL_MULTICAST, BASE + VX_COMMAND);
136
137 vxsetlink();
138 /*{
139 int i,j;
140 i = CONNECTOR_TX;
141 GO_WINDOW(3);
142 j = inl(BASE + VX_W3_INTERNAL_CFG) & ~INTERNAL_CONNECTOR_MASK;
143 outl(BASE + VX_W3_INTERNAL_CFG, j | (i <<INTERNAL_CONNECTOR_BITS));
144 GO_WINDOW(4);
145 outw(LINKBEAT_ENABLE, BASE + VX_W4_MEDIA_TYPE);
146 GO_WINDOW(1);
147 }*/
148
149 /* start tranciever and receiver */
150 outw(RX_ENABLE, BASE + VX_COMMAND);
151 outw(TX_ENABLE, BASE + VX_COMMAND);
152
153 }
154
155 /**************************************************************************
156 ETH_TRANSMIT - Transmit a frame
157 ***************************************************************************/
158 static char padmap[] = {
159 0, 3, 2, 1};
160
t595_transmit(struct nic * nic,const char * d,unsigned int t,unsigned int s,const char * p)161 static void t595_transmit(
162 struct nic *nic,
163 const char *d, /* Destination */
164 unsigned int t, /* Type */
165 unsigned int s, /* size */
166 const char *p) /* Packet */
167 {
168 register int len;
169 int pad;
170 int status;
171
172 #ifdef EDEBUG
173 printf("{l=%d,t=%hX}",s+ETH_HLEN,t);
174 #endif
175
176 /* swap bytes of type */
177 t= htons(t);
178
179 len=s+ETH_HLEN; /* actual length of packet */
180 pad = padmap[len & 3];
181
182 /*
183 * The 3c595 automatically pads short packets to minimum ethernet length,
184 * but we drop packets that are too large. Perhaps we should truncate
185 * them instead?
186 */
187 if (len + pad > ETH_FRAME_LEN) {
188 return;
189 }
190
191 /* drop acknowledgements */
192 while(( status=inb(BASE + VX_W1_TX_STATUS) )& TXS_COMPLETE ) {
193 if(status & (TXS_UNDERRUN|TXS_MAX_COLLISION|TXS_STATUS_OVERFLOW)) {
194 outw(TX_RESET, BASE + VX_COMMAND);
195 outw(TX_ENABLE, BASE + VX_COMMAND);
196 }
197
198 outb(0x0, BASE + VX_W1_TX_STATUS);
199 }
200
201 while (inw(BASE + VX_W1_FREE_TX) < len + pad + 4) {
202 /* no room in FIFO */
203 }
204
205 outw(len, BASE + VX_W1_TX_PIO_WR_1);
206 outw(0x0, BASE + VX_W1_TX_PIO_WR_1); /* Second dword meaningless */
207
208 /* write packet */
209 outsw(BASE + VX_W1_TX_PIO_WR_1, d, ETH_ALEN/2);
210 outsw(BASE + VX_W1_TX_PIO_WR_1, nic->node_addr, ETH_ALEN/2);
211 outw(t, BASE + VX_W1_TX_PIO_WR_1);
212 outsw(BASE + VX_W1_TX_PIO_WR_1, p, s / 2);
213 if (s & 1)
214 outb(*(p+s - 1), BASE + VX_W1_TX_PIO_WR_1);
215
216 while (pad--)
217 outb(0, BASE + VX_W1_TX_PIO_WR_1); /* Padding */
218
219 /* wait for Tx complete */
220 while((inw(BASE + VX_STATUS) & S_COMMAND_IN_PROGRESS) != 0)
221 ;
222 }
223
224 /**************************************************************************
225 ETH_POLL - Wait for a frame
226 ***************************************************************************/
t595_poll(struct nic * nic,int retrieve)227 static int t595_poll(struct nic *nic, int retrieve)
228 {
229 /* common variables */
230 /* variables for 3C595 */
231 short status, cst;
232 register short rx_fifo;
233
234 cst=inw(BASE + VX_STATUS);
235
236 #ifdef EDEBUG
237 if(cst & 0x1FFF)
238 printf("-%hX-",cst);
239 #endif
240
241 if( (cst & S_RX_COMPLETE)==0 ) {
242 /* acknowledge everything */
243 outw(ACK_INTR | cst, BASE + VX_COMMAND);
244 outw(C_INTR_LATCH, BASE + VX_COMMAND);
245
246 return 0;
247 }
248
249 status = inw(BASE + VX_W1_RX_STATUS);
250 #ifdef EDEBUG
251 printf("*%hX*",status);
252 #endif
253
254 if (status & ERR_RX) {
255 outw(RX_DISCARD_TOP_PACK, BASE + VX_COMMAND);
256 return 0;
257 }
258
259 rx_fifo = status & RX_BYTES_MASK;
260 if (rx_fifo==0)
261 return 0;
262
263 if ( ! retrieve ) return 1;
264
265 /* read packet */
266 #ifdef EDEBUG
267 printf("[l=%d",rx_fifo);
268 #endif
269 insw(BASE + VX_W1_RX_PIO_RD_1, nic->packet, rx_fifo / 2);
270 if(rx_fifo & 1)
271 nic->packet[rx_fifo-1]=inb(BASE + VX_W1_RX_PIO_RD_1);
272 nic->packetlen=rx_fifo;
273
274 while(1) {
275 status = inw(BASE + VX_W1_RX_STATUS);
276 #ifdef EDEBUG
277 printf("*%hX*",status);
278 #endif
279 rx_fifo = status & RX_BYTES_MASK;
280
281 if(rx_fifo>0) {
282 insw(BASE + VX_W1_RX_PIO_RD_1, nic->packet+nic->packetlen, rx_fifo / 2);
283 if(rx_fifo & 1)
284 nic->packet[nic->packetlen+rx_fifo-1]=inb(BASE + VX_W1_RX_PIO_RD_1);
285 nic->packetlen+=rx_fifo;
286 #ifdef EDEBUG
287 printf("+%d",rx_fifo);
288 #endif
289 }
290 if(( status & RX_INCOMPLETE )==0) {
291 #ifdef EDEBUG
292 printf("=%d",nic->packetlen);
293 #endif
294 break;
295 }
296 udelay(1000);
297 }
298
299 /* acknowledge reception of packet */
300 outw(RX_DISCARD_TOP_PACK, BASE + VX_COMMAND);
301 while (inw(BASE + VX_STATUS) & S_COMMAND_IN_PROGRESS);
302 #ifdef EDEBUG
303 {
304 unsigned short type = 0; /* used by EDEBUG */
305 type = (nic->packet[12]<<8) | nic->packet[13];
306 if(nic->packet[0]+nic->packet[1]+nic->packet[2]+nic->packet[3]+nic->packet[4]+
307 nic->packet[5] == 0xFF*ETH_ALEN)
308 printf(",t=%hX,b]",type);
309 else
310 printf(",t=%hX]",type);
311 }
312 #endif
313 return 1;
314 }
315
316
317 /*************************************************************************
318 3Com 595 - specific routines
319 **************************************************************************/
320
321 static int
eeprom_rdy()322 eeprom_rdy()
323 {
324 int i;
325
326 for (i = 0; is_eeprom_busy(BASE) && i < MAX_EEPROMBUSY; i++)
327 udelay(1000);
328 if (i >= MAX_EEPROMBUSY) {
329 /* printf("3c595: eeprom failed to come ready.\n"); */
330 printf("3c595: eeprom is busy.\n"); /* memory in EPROM is tight */
331 return (0);
332 }
333 return (1);
334 }
335
336 /*
337 * get_e: gets a 16 bits word from the EEPROM. we must have set the window
338 * before
339 */
340 static int
get_e(offset)341 get_e(offset)
342 int offset;
343 {
344 if (!eeprom_rdy())
345 return (0xffff);
346 outw(EEPROM_CMD_RD | offset, BASE + VX_W0_EEPROM_COMMAND);
347 if (!eeprom_rdy())
348 return (0xffff);
349 return (inw(BASE + VX_W0_EEPROM_DATA));
350 }
351
352 static void
vxgetlink(void)353 vxgetlink(void)
354 {
355 int n, k;
356
357 GO_WINDOW(3);
358 vx_connectors = inw(BASE + VX_W3_RESET_OPT) & 0x7f;
359 for (n = 0, k = 0; k < VX_CONNECTORS; k++) {
360 if (vx_connectors & conn_tab[k].bit) {
361 if (n > 0) {
362 printf("/");
363 }
364 printf(conn_tab[k].name);
365 n++;
366 }
367 }
368 if (vx_connectors == 0) {
369 printf("no connectors!");
370 return;
371 }
372 GO_WINDOW(3);
373 vx_connector = (inl(BASE + VX_W3_INTERNAL_CFG)
374 & INTERNAL_CONNECTOR_MASK)
375 >> INTERNAL_CONNECTOR_BITS;
376 if (vx_connector & 0x10) {
377 vx_connector &= 0x0f;
378 printf("[*%s*]", conn_tab[vx_connector].name);
379 printf(": disable 'auto select' with DOS util!");
380 } else {
381 printf("[*%s*]", conn_tab[vx_connector].name);
382 }
383 }
384
385 static void
vxsetlink(void)386 vxsetlink(void)
387 {
388 int i, j;
389 char *reason, *warning;
390 static char prev_conn = -1;
391
392 if (prev_conn == -1) {
393 prev_conn = vx_connector;
394 }
395
396 i = vx_connector; /* default in EEPROM */
397 reason = "default";
398 warning = 0;
399
400 if ((vx_connectors & conn_tab[vx_connector].bit) == 0) {
401 warning = "strange connector type in EEPROM.";
402 reason = "forced";
403 i = CONNECTOR_UTP;
404 }
405
406 if (warning != 0) {
407 printf("warning: %s\n", warning);
408 }
409 printf("selected %s. (%s)\n", conn_tab[i].name, reason);
410
411 /* Set the selected connector. */
412 GO_WINDOW(3);
413 j = inl(BASE + VX_W3_INTERNAL_CFG) & ~INTERNAL_CONNECTOR_MASK;
414 outl(j | (i <<INTERNAL_CONNECTOR_BITS), BASE + VX_W3_INTERNAL_CFG);
415
416 /* First, disable all. */
417 outw(STOP_TRANSCEIVER, BASE + VX_COMMAND);
418 udelay(8000);
419 GO_WINDOW(4);
420 outw(0, BASE + VX_W4_MEDIA_TYPE);
421
422 /* Second, enable the selected one. */
423 switch(i) {
424 case CONNECTOR_UTP:
425 GO_WINDOW(4);
426 outw(ENABLE_UTP, BASE + VX_W4_MEDIA_TYPE);
427 break;
428 case CONNECTOR_BNC:
429 outw(START_TRANSCEIVER,BASE + VX_COMMAND);
430 udelay(8000);
431 break;
432 case CONNECTOR_TX:
433 case CONNECTOR_FX:
434 GO_WINDOW(4);
435 outw(LINKBEAT_ENABLE, BASE + VX_W4_MEDIA_TYPE);
436 break;
437 default: /* AUI and MII fall here */
438 break;
439 }
440 GO_WINDOW(1);
441 }
442
t595_disable(struct dev * dev)443 static void t595_disable(struct dev *dev)
444 {
445 struct nic *nic = (struct nic *)dev;
446 t595_reset(nic);
447
448 outw(STOP_TRANSCEIVER, BASE + VX_COMMAND);
449 udelay(8000);
450 GO_WINDOW(4);
451 outw(0, BASE + VX_W4_MEDIA_TYPE);
452 GO_WINDOW(1);
453 }
454
t595_irq(struct nic * nic __unused,irq_action_t action __unused)455 static void t595_irq(struct nic *nic __unused, irq_action_t action __unused)
456 {
457 switch ( action ) {
458 case DISABLE :
459 break;
460 case ENABLE :
461 break;
462 case FORCE :
463 break;
464 }
465 }
466
467 /**************************************************************************
468 ETH_PROBE - Look for an adapter
469 ***************************************************************************/
t595_probe(struct dev * dev,struct pci_device * pci)470 static int t595_probe(struct dev *dev, struct pci_device *pci)
471 {
472 struct nic *nic = (struct nic *)dev;
473 int i;
474 unsigned short *p;
475
476 if (pci->ioaddr == 0)
477 return 0;
478 /* eth_nic_base = probeaddrs[0] & ~3; */
479 eth_nic_base = pci->ioaddr;
480
481 nic->irqno = 0;
482 nic->ioaddr = pci->ioaddr & ~3;
483
484 GO_WINDOW(0);
485 outw(GLOBAL_RESET, BASE + VX_COMMAND);
486 VX_BUSY_WAIT;
487
488 vxgetlink();
489
490 /*
491 printf("\nEEPROM:");
492 for (i = 0; i < (EEPROMSIZE/2); i++) {
493 printf("%hX:", get_e(i));
494 }
495 printf("\n");
496 */
497 /*
498 * Read the station address from the eeprom
499 */
500 p = (unsigned short *) nic->node_addr;
501 for (i = 0; i < 3; i++) {
502 GO_WINDOW(0);
503 p[i] = htons(get_e(EEPROM_OEM_ADDR_0 + i));
504 GO_WINDOW(2);
505 outw(ntohs(p[i]), BASE + VX_W2_ADDR_0 + (i * 2));
506 }
507
508 printf("Ethernet address: %!\n", nic->node_addr);
509
510 t595_reset(nic);
511 dev->disable = t595_disable;
512 nic->poll = t595_poll;
513 nic->transmit = t595_transmit;
514 nic->irq = t595_irq;
515 return 1;
516
517 }
518
519 static struct pci_id t595_nics[] = {
520 PCI_ROM(0x10b7, 0x5900, "3c590", "3Com590"), /* Vortex 10Mbps */
521 PCI_ROM(0x10b7, 0x5950, "3c595", "3Com595"), /* Vortex 100baseTx */
522 PCI_ROM(0x10b7, 0x5951, "3c595-1", "3Com595"), /* Vortex 100baseT4 */
523 PCI_ROM(0x10b7, 0x5952, "3c595-2", "3Com595"), /* Vortex 100base-MII */
524 PCI_ROM(0x10b7, 0x9000, "3c900-tpo", "3Com900-TPO"), /* 10 Base TPO */
525 PCI_ROM(0x10b7, 0x9001, "3c900-t4", "3Com900-Combo"), /* 10/100 T4 */
526 PCI_ROM(0x10b7, 0x9004, "3c900b-tpo", "3Com900B-TPO"), /* 10 Base TPO */
527 PCI_ROM(0x10b7, 0x9005, "3c900b-combo", "3Com900B-Combo"), /* 10 Base Combo */
528 PCI_ROM(0x10b7, 0x9006, "3c900b-tpb2", "3Com900B-2/T"), /* 10 Base TP and Base2 */
529 PCI_ROM(0x10b7, 0x900a, "3c900b-fl", "3Com900B-FL"), /* 10 Base F */
530 PCI_ROM(0x10b7, 0x9800, "3c980-cyclone-1", "3Com980-Cyclone"), /* Cyclone */
531 PCI_ROM(0x10b7, 0x9805, "3c9805-1", "3Com9805"), /* Dual Port Server Cyclone */
532 PCI_ROM(0x10b7, 0x7646, "3csoho100-tx-1", "3CSOHO100-TX"), /* Hurricane */
533 PCI_ROM(0x10b7, 0x4500, "3c450-1", "3Com450 HomePNA Tornado"),
534 };
535
536 struct pci_driver t595_driver = {
537 .type = NIC_DRIVER,
538 .name = "3C595",
539 .probe = t595_probe,
540 .ids = t595_nics,
541 .id_count = sizeof(t595_nics)/sizeof(t595_nics[0]),
542 .class = 0,
543 };
544
545 /*
546 * Local variables:
547 * c-basic-offset: 8
548 * End:
549 */
550
551