1// SPDX-License-Identifier: GPL-2.0 2/dts-v1/; 3 4#include <dt-bindings/clock/qcom,gcc-msm8960.h> 5#include <dt-bindings/clock/qcom,lcc-msm8960.h> 6#include <dt-bindings/reset/qcom,gcc-msm8960.h> 7#include <dt-bindings/clock/qcom,mmcc-msm8960.h> 8#include <dt-bindings/clock/qcom,rpmcc.h> 9#include <dt-bindings/soc/qcom,gsbi.h> 10#include <dt-bindings/interrupt-controller/irq.h> 11#include <dt-bindings/interrupt-controller/arm-gic.h> 12/ { 13 #address-cells = <1>; 14 #size-cells = <1>; 15 model = "Qualcomm APQ8064"; 16 compatible = "qcom,apq8064"; 17 interrupt-parent = <&intc>; 18 19 reserved-memory { 20 #address-cells = <1>; 21 #size-cells = <1>; 22 ranges; 23 24 smem_region: smem@80000000 { 25 reg = <0x80000000 0x200000>; 26 no-map; 27 }; 28 29 wcnss_mem: wcnss@8f000000 { 30 reg = <0x8f000000 0x700000>; 31 no-map; 32 }; 33 }; 34 35 cpus { 36 #address-cells = <1>; 37 #size-cells = <0>; 38 39 cpu0: cpu@0 { 40 compatible = "qcom,krait"; 41 enable-method = "qcom,kpss-acc-v1"; 42 device_type = "cpu"; 43 reg = <0>; 44 next-level-cache = <&l2>; 45 qcom,acc = <&acc0>; 46 qcom,saw = <&saw0>; 47 cpu-idle-states = <&cpu_spc>; 48 }; 49 50 cpu1: cpu@1 { 51 compatible = "qcom,krait"; 52 enable-method = "qcom,kpss-acc-v1"; 53 device_type = "cpu"; 54 reg = <1>; 55 next-level-cache = <&l2>; 56 qcom,acc = <&acc1>; 57 qcom,saw = <&saw1>; 58 cpu-idle-states = <&cpu_spc>; 59 }; 60 61 cpu2: cpu@2 { 62 compatible = "qcom,krait"; 63 enable-method = "qcom,kpss-acc-v1"; 64 device_type = "cpu"; 65 reg = <2>; 66 next-level-cache = <&l2>; 67 qcom,acc = <&acc2>; 68 qcom,saw = <&saw2>; 69 cpu-idle-states = <&cpu_spc>; 70 }; 71 72 cpu3: cpu@3 { 73 compatible = "qcom,krait"; 74 enable-method = "qcom,kpss-acc-v1"; 75 device_type = "cpu"; 76 reg = <3>; 77 next-level-cache = <&l2>; 78 qcom,acc = <&acc3>; 79 qcom,saw = <&saw3>; 80 cpu-idle-states = <&cpu_spc>; 81 }; 82 83 l2: l2-cache { 84 compatible = "cache"; 85 cache-level = <2>; 86 cache-unified; 87 }; 88 89 idle-states { 90 cpu_spc: cpu-spc { 91 compatible = "qcom,idle-state-spc", 92 "arm,idle-state"; 93 entry-latency-us = <400>; 94 exit-latency-us = <900>; 95 min-residency-us = <3000>; 96 }; 97 }; 98 }; 99 100 memory@0 { 101 device_type = "memory"; 102 reg = <0x0 0x0>; 103 }; 104 105 thermal-zones { 106 cpu0-thermal { 107 polling-delay-passive = <250>; 108 polling-delay = <1000>; 109 110 thermal-sensors = <&tsens 7>; 111 coefficients = <1199 0>; 112 113 trips { 114 cpu_alert0: trip0 { 115 temperature = <75000>; 116 hysteresis = <2000>; 117 type = "passive"; 118 }; 119 cpu_crit0: trip1 { 120 temperature = <110000>; 121 hysteresis = <2000>; 122 type = "critical"; 123 }; 124 }; 125 }; 126 127 cpu1-thermal { 128 polling-delay-passive = <250>; 129 polling-delay = <1000>; 130 131 thermal-sensors = <&tsens 8>; 132 coefficients = <1132 0>; 133 134 trips { 135 cpu_alert1: trip0 { 136 temperature = <75000>; 137 hysteresis = <2000>; 138 type = "passive"; 139 }; 140 cpu_crit1: trip1 { 141 temperature = <110000>; 142 hysteresis = <2000>; 143 type = "critical"; 144 }; 145 }; 146 }; 147 148 cpu2-thermal { 149 polling-delay-passive = <250>; 150 polling-delay = <1000>; 151 152 thermal-sensors = <&tsens 9>; 153 coefficients = <1199 0>; 154 155 trips { 156 cpu_alert2: trip0 { 157 temperature = <75000>; 158 hysteresis = <2000>; 159 type = "passive"; 160 }; 161 cpu_crit2: trip1 { 162 temperature = <110000>; 163 hysteresis = <2000>; 164 type = "critical"; 165 }; 166 }; 167 }; 168 169 cpu3-thermal { 170 polling-delay-passive = <250>; 171 polling-delay = <1000>; 172 173 thermal-sensors = <&tsens 10>; 174 coefficients = <1132 0>; 175 176 trips { 177 cpu_alert3: trip0 { 178 temperature = <75000>; 179 hysteresis = <2000>; 180 type = "passive"; 181 }; 182 cpu_crit3: trip1 { 183 temperature = <110000>; 184 hysteresis = <2000>; 185 type = "critical"; 186 }; 187 }; 188 }; 189 }; 190 191 cpu-pmu { 192 compatible = "qcom,krait-pmu"; 193 interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>; 194 }; 195 196 clocks { 197 cxo_board: cxo_board { 198 compatible = "fixed-clock"; 199 #clock-cells = <0>; 200 clock-frequency = <19200000>; 201 }; 202 203 pxo_board: pxo_board { 204 compatible = "fixed-clock"; 205 #clock-cells = <0>; 206 clock-frequency = <27000000>; 207 }; 208 209 sleep_clk: sleep_clk { 210 compatible = "fixed-clock"; 211 #clock-cells = <0>; 212 clock-frequency = <32768>; 213 }; 214 }; 215 216 sfpb_mutex: hwmutex { 217 compatible = "qcom,sfpb-mutex"; 218 syscon = <&sfpb_wrapper_mutex 0x604 0x4>; 219 #hwlock-cells = <1>; 220 }; 221 222 smem { 223 compatible = "qcom,smem"; 224 memory-region = <&smem_region>; 225 226 hwlocks = <&sfpb_mutex 3>; 227 }; 228 229 smsm { 230 compatible = "qcom,smsm"; 231 232 #address-cells = <1>; 233 #size-cells = <0>; 234 235 qcom,ipc-1 = <&l2cc 8 4>; 236 qcom,ipc-2 = <&l2cc 8 14>; 237 qcom,ipc-3 = <&l2cc 8 23>; 238 qcom,ipc-4 = <&sps_sic_non_secure 0x4094 0>; 239 240 apps_smsm: apps@0 { 241 reg = <0>; 242 #qcom,smem-state-cells = <1>; 243 }; 244 245 modem_smsm: modem@1 { 246 reg = <1>; 247 interrupts = <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>; 248 249 interrupt-controller; 250 #interrupt-cells = <2>; 251 }; 252 253 q6_smsm: q6@2 { 254 reg = <2>; 255 interrupts = <GIC_SPI 89 IRQ_TYPE_EDGE_RISING>; 256 257 interrupt-controller; 258 #interrupt-cells = <2>; 259 }; 260 261 wcnss_smsm: wcnss@3 { 262 reg = <3>; 263 interrupts = <GIC_SPI 204 IRQ_TYPE_EDGE_RISING>; 264 265 interrupt-controller; 266 #interrupt-cells = <2>; 267 }; 268 269 dsps_smsm: dsps@4 { 270 reg = <4>; 271 interrupts = <GIC_SPI 137 IRQ_TYPE_EDGE_RISING>; 272 273 interrupt-controller; 274 #interrupt-cells = <2>; 275 }; 276 }; 277 278 firmware { 279 scm { 280 compatible = "qcom,scm-apq8064", "qcom,scm"; 281 282 clocks = <&rpmcc RPM_DAYTONA_FABRIC_CLK>; 283 clock-names = "core"; 284 }; 285 }; 286 287 soc: soc { 288 #address-cells = <1>; 289 #size-cells = <1>; 290 ranges; 291 compatible = "simple-bus"; 292 293 tlmm_pinmux: pinctrl@800000 { 294 compatible = "qcom,apq8064-pinctrl"; 295 reg = <0x800000 0x4000>; 296 297 gpio-controller; 298 gpio-ranges = <&tlmm_pinmux 0 0 90>; 299 #gpio-cells = <2>; 300 interrupt-controller; 301 #interrupt-cells = <2>; 302 interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; 303 304 pinctrl-names = "default"; 305 pinctrl-0 = <&ps_hold_default_state>; 306 }; 307 308 sfpb_wrapper_mutex: syscon@1200000 { 309 compatible = "syscon"; 310 reg = <0x01200000 0x8000>; 311 }; 312 313 intc: interrupt-controller@2000000 { 314 compatible = "qcom,msm-qgic2"; 315 interrupt-controller; 316 #interrupt-cells = <3>; 317 reg = <0x02000000 0x1000>, 318 <0x02002000 0x1000>; 319 }; 320 321 timer@200a000 { 322 compatible = "qcom,kpss-wdt-apq8064", "qcom,kpss-timer", 323 "qcom,msm-timer"; 324 interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>, 325 <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>, 326 <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>; 327 reg = <0x0200a000 0x100>; 328 clock-frequency = <27000000>; 329 cpu-offset = <0x80000>; 330 }; 331 332 acc0: clock-controller@2088000 { 333 compatible = "qcom,kpss-acc-v1"; 334 reg = <0x02088000 0x1000>, <0x02008000 0x1000>; 335 clocks = <&gcc PLL8_VOTE>, <&pxo_board>; 336 clock-names = "pll8_vote", "pxo"; 337 clock-output-names = "acpu0_aux"; 338 #clock-cells = <0>; 339 }; 340 341 acc1: clock-controller@2098000 { 342 compatible = "qcom,kpss-acc-v1"; 343 reg = <0x02098000 0x1000>, <0x02008000 0x1000>; 344 clocks = <&gcc PLL8_VOTE>, <&pxo_board>; 345 clock-names = "pll8_vote", "pxo"; 346 clock-output-names = "acpu1_aux"; 347 #clock-cells = <0>; 348 }; 349 350 acc2: clock-controller@20a8000 { 351 compatible = "qcom,kpss-acc-v1"; 352 reg = <0x020a8000 0x1000>, <0x02008000 0x1000>; 353 clocks = <&gcc PLL8_VOTE>, <&pxo_board>; 354 clock-names = "pll8_vote", "pxo"; 355 clock-output-names = "acpu2_aux"; 356 #clock-cells = <0>; 357 }; 358 359 acc3: clock-controller@20b8000 { 360 compatible = "qcom,kpss-acc-v1"; 361 reg = <0x020b8000 0x1000>, <0x02008000 0x1000>; 362 clocks = <&gcc PLL8_VOTE>, <&pxo_board>; 363 clock-names = "pll8_vote", "pxo"; 364 clock-output-names = "acpu3_aux"; 365 #clock-cells = <0>; 366 }; 367 368 saw0: power-manager@2089000 { 369 compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2"; 370 reg = <0x02089000 0x1000>, <0x02009000 0x1000>; 371 372 saw0_vreg: regulator { 373 regulator-min-microvolt = <850000>; 374 regulator-max-microvolt = <1300000>; 375 }; 376 }; 377 378 saw1: power-manager@2099000 { 379 compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2"; 380 reg = <0x02099000 0x1000>, <0x02009000 0x1000>; 381 382 saw1_vreg: regulator { 383 regulator-min-microvolt = <850000>; 384 regulator-max-microvolt = <1300000>; 385 }; 386 }; 387 388 saw2: power-manager@20a9000 { 389 compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2"; 390 reg = <0x020a9000 0x1000>, <0x02009000 0x1000>; 391 392 saw2_vreg: regulator { 393 regulator-min-microvolt = <850000>; 394 regulator-max-microvolt = <1300000>; 395 }; 396 }; 397 398 saw3: power-manager@20b9000 { 399 compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2"; 400 reg = <0x020b9000 0x1000>, <0x02009000 0x1000>; 401 402 saw3_vreg: regulator { 403 regulator-min-microvolt = <850000>; 404 regulator-max-microvolt = <1300000>; 405 }; 406 }; 407 408 sps_sic_non_secure: sps-sic-non-secure@12100000 { 409 compatible = "syscon"; 410 reg = <0x12100000 0x10000>; 411 }; 412 413 gsbi1: gsbi@12440000 { 414 status = "disabled"; 415 compatible = "qcom,gsbi-v1.0.0"; 416 cell-index = <1>; 417 reg = <0x12440000 0x100>; 418 clocks = <&gcc GSBI1_H_CLK>; 419 clock-names = "iface"; 420 #address-cells = <1>; 421 #size-cells = <1>; 422 ranges; 423 424 syscon-tcsr = <&tcsr>; 425 426 gsbi1_serial: serial@12450000 { 427 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; 428 reg = <0x12450000 0x100>, 429 <0x12400000 0x03>; 430 interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>; 431 clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>; 432 clock-names = "core", "iface"; 433 status = "disabled"; 434 }; 435 436 gsbi1_i2c: i2c@12460000 { 437 compatible = "qcom,i2c-qup-v1.1.1"; 438 pinctrl-0 = <&i2c1_default_state>; 439 pinctrl-1 = <&i2c1_sleep_state>; 440 pinctrl-names = "default", "sleep"; 441 reg = <0x12460000 0x1000>; 442 interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>; 443 clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; 444 clock-names = "core", "iface"; 445 #address-cells = <1>; 446 #size-cells = <0>; 447 status = "disabled"; 448 }; 449 450 }; 451 452 gsbi2: gsbi@12480000 { 453 status = "disabled"; 454 compatible = "qcom,gsbi-v1.0.0"; 455 cell-index = <2>; 456 reg = <0x12480000 0x100>; 457 clocks = <&gcc GSBI2_H_CLK>; 458 clock-names = "iface"; 459 #address-cells = <1>; 460 #size-cells = <1>; 461 ranges; 462 463 syscon-tcsr = <&tcsr>; 464 465 gsbi2_i2c: i2c@124a0000 { 466 compatible = "qcom,i2c-qup-v1.1.1"; 467 reg = <0x124a0000 0x1000>; 468 pinctrl-0 = <&i2c2_default_state>; 469 pinctrl-1 = <&i2c2_sleep_state>; 470 pinctrl-names = "default", "sleep"; 471 interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>; 472 clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; 473 clock-names = "core", "iface"; 474 #address-cells = <1>; 475 #size-cells = <0>; 476 status = "disabled"; 477 }; 478 }; 479 480 gsbi3: gsbi@16200000 { 481 status = "disabled"; 482 compatible = "qcom,gsbi-v1.0.0"; 483 cell-index = <3>; 484 reg = <0x16200000 0x100>; 485 clocks = <&gcc GSBI3_H_CLK>; 486 clock-names = "iface"; 487 #address-cells = <1>; 488 #size-cells = <1>; 489 ranges; 490 gsbi3_i2c: i2c@16280000 { 491 compatible = "qcom,i2c-qup-v1.1.1"; 492 pinctrl-0 = <&i2c3_default_state>; 493 pinctrl-1 = <&i2c3_sleep_state>; 494 pinctrl-names = "default", "sleep"; 495 reg = <0x16280000 0x1000>; 496 interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>; 497 clocks = <&gcc GSBI3_QUP_CLK>, 498 <&gcc GSBI3_H_CLK>; 499 clock-names = "core", "iface"; 500 #address-cells = <1>; 501 #size-cells = <0>; 502 status = "disabled"; 503 }; 504 }; 505 506 gsbi4: gsbi@16300000 { 507 status = "disabled"; 508 compatible = "qcom,gsbi-v1.0.0"; 509 cell-index = <4>; 510 reg = <0x16300000 0x03>; 511 clocks = <&gcc GSBI4_H_CLK>; 512 clock-names = "iface"; 513 #address-cells = <1>; 514 #size-cells = <1>; 515 ranges; 516 517 gsbi4_serial: serial@16340000 { 518 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; 519 reg = <0x16340000 0x100>, 520 <0x16300000 0x3>; 521 interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>; 522 pinctrl-0 = <&gsbi4_uart_pin_a>; 523 pinctrl-names = "default"; 524 clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>; 525 clock-names = "core", "iface"; 526 status = "disabled"; 527 }; 528 529 gsbi4_i2c: i2c@16380000 { 530 compatible = "qcom,i2c-qup-v1.1.1"; 531 pinctrl-0 = <&i2c4_default_state>; 532 pinctrl-1 = <&i2c4_sleep_state>; 533 pinctrl-names = "default", "sleep"; 534 reg = <0x16380000 0x1000>; 535 interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>; 536 clocks = <&gcc GSBI4_QUP_CLK>, 537 <&gcc GSBI4_H_CLK>; 538 clock-names = "core", "iface"; 539 status = "disabled"; 540 }; 541 }; 542 543 gsbi5: gsbi@1a200000 { 544 status = "disabled"; 545 compatible = "qcom,gsbi-v1.0.0"; 546 cell-index = <5>; 547 reg = <0x1a200000 0x03>; 548 clocks = <&gcc GSBI5_H_CLK>; 549 clock-names = "iface"; 550 #address-cells = <1>; 551 #size-cells = <1>; 552 ranges; 553 554 gsbi5_serial: serial@1a240000 { 555 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; 556 reg = <0x1a240000 0x100>, 557 <0x1a200000 0x03>; 558 interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; 559 clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; 560 clock-names = "core", "iface"; 561 status = "disabled"; 562 }; 563 564 gsbi5_spi: spi@1a280000 { 565 compatible = "qcom,spi-qup-v1.1.1"; 566 reg = <0x1a280000 0x1000>; 567 interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; 568 pinctrl-0 = <&spi5_default_state>; 569 pinctrl-1 = <&spi5_sleep_state>; 570 pinctrl-names = "default", "sleep"; 571 clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; 572 clock-names = "core", "iface"; 573 status = "disabled"; 574 #address-cells = <1>; 575 #size-cells = <0>; 576 }; 577 }; 578 579 gsbi6: gsbi@16500000 { 580 status = "disabled"; 581 compatible = "qcom,gsbi-v1.0.0"; 582 cell-index = <6>; 583 reg = <0x16500000 0x03>; 584 clocks = <&gcc GSBI6_H_CLK>; 585 clock-names = "iface"; 586 #address-cells = <1>; 587 #size-cells = <1>; 588 ranges; 589 590 gsbi6_serial: serial@16540000 { 591 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; 592 reg = <0x16540000 0x100>, 593 <0x16500000 0x03>; 594 interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>; 595 clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>; 596 clock-names = "core", "iface"; 597 status = "disabled"; 598 }; 599 600 gsbi6_i2c: i2c@16580000 { 601 compatible = "qcom,i2c-qup-v1.1.1"; 602 pinctrl-0 = <&i2c6_default_state>; 603 pinctrl-1 = <&i2c6_sleep_state>; 604 pinctrl-names = "default", "sleep"; 605 reg = <0x16580000 0x1000>; 606 interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>; 607 clocks = <&gcc GSBI6_QUP_CLK>, 608 <&gcc GSBI6_H_CLK>; 609 clock-names = "core", "iface"; 610 status = "disabled"; 611 }; 612 }; 613 614 gsbi7: gsbi@16600000 { 615 status = "disabled"; 616 compatible = "qcom,gsbi-v1.0.0"; 617 cell-index = <7>; 618 reg = <0x16600000 0x100>; 619 clocks = <&gcc GSBI7_H_CLK>; 620 clock-names = "iface"; 621 #address-cells = <1>; 622 #size-cells = <1>; 623 ranges; 624 syscon-tcsr = <&tcsr>; 625 626 gsbi7_serial: serial@16640000 { 627 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; 628 reg = <0x16640000 0x1000>, 629 <0x16600000 0x1000>; 630 interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>; 631 clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>; 632 clock-names = "core", "iface"; 633 status = "disabled"; 634 }; 635 636 gsbi7_i2c: i2c@16680000 { 637 compatible = "qcom,i2c-qup-v1.1.1"; 638 pinctrl-0 = <&i2c7_default_state>; 639 pinctrl-1 = <&i2c7_sleep_state>; 640 pinctrl-names = "default", "sleep"; 641 reg = <0x16680000 0x1000>; 642 interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>; 643 clocks = <&gcc GSBI7_QUP_CLK>, 644 <&gcc GSBI7_H_CLK>; 645 clock-names = "core", "iface"; 646 status = "disabled"; 647 }; 648 }; 649 650 rng@1a500000 { 651 compatible = "qcom,prng"; 652 reg = <0x1a500000 0x200>; 653 clocks = <&gcc PRNG_CLK>; 654 clock-names = "core"; 655 }; 656 657 ssbi2: ssbi@c00000 { 658 compatible = "qcom,ssbi"; 659 reg = <0x00c00000 0x1000>; 660 qcom,controller-type = "pmic-arbiter"; 661 }; 662 663 ssbi: ssbi@500000 { 664 compatible = "qcom,ssbi"; 665 reg = <0x00500000 0x1000>; 666 qcom,controller-type = "pmic-arbiter"; 667 }; 668 669 qfprom: efuse@700000 { 670 compatible = "qcom,apq8064-qfprom", "qcom,qfprom"; 671 reg = <0x00700000 0x1000>; 672 #address-cells = <1>; 673 #size-cells = <1>; 674 675 tsens_calib: calib@404 { 676 reg = <0x404 0x10>; 677 }; 678 tsens_backup: backup-calib@414 { 679 reg = <0x414 0x10>; 680 }; 681 }; 682 683 gcc: clock-controller@900000 { 684 compatible = "qcom,gcc-apq8064", "syscon"; 685 reg = <0x00900000 0x4000>; 686 #clock-cells = <1>; 687 #reset-cells = <1>; 688 clocks = <&cxo_board>, 689 <&pxo_board>, 690 <&lcc PLL4>; 691 clock-names = "cxo", "pxo", "pll4"; 692 693 tsens: thermal-sensor { 694 compatible = "qcom,msm8960-tsens"; 695 696 nvmem-cells = <&tsens_calib>, <&tsens_backup>; 697 nvmem-cell-names = "calib", "calib_backup"; 698 interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; 699 interrupt-names = "uplow"; 700 701 #qcom,sensors = <11>; 702 #thermal-sensor-cells = <1>; 703 }; 704 }; 705 706 lcc: clock-controller@28000000 { 707 compatible = "qcom,lcc-apq8064"; 708 reg = <0x28000000 0x1000>; 709 #clock-cells = <1>; 710 #reset-cells = <1>; 711 clocks = <&pxo_board>, 712 <&gcc PLL4_VOTE>, 713 <0>, 714 <0>, <0>, 715 <0>, <0>, 716 <0>; 717 clock-names = "pxo", 718 "pll4_vote", 719 "mi2s_codec_clk", 720 "codec_i2s_mic_codec_clk", 721 "spare_i2s_mic_codec_clk", 722 "codec_i2s_spkr_codec_clk", 723 "spare_i2s_spkr_codec_clk", 724 "pcm_codec_clk"; 725 }; 726 727 mmcc: clock-controller@4000000 { 728 compatible = "qcom,mmcc-apq8064"; 729 reg = <0x4000000 0x1000>; 730 #clock-cells = <1>; 731 #power-domain-cells = <1>; 732 #reset-cells = <1>; 733 clocks = <&pxo_board>, 734 <&gcc PLL3>, 735 <&gcc PLL8_VOTE>, 736 <&dsi0_phy 1>, 737 <&dsi0_phy 0>, 738 <&dsi1_phy 1>, 739 <&dsi1_phy 0>, 740 <&hdmi_phy>; 741 clock-names = "pxo", 742 "pll3", 743 "pll8_vote", 744 "dsi1pll", 745 "dsi1pllbyte", 746 "dsi2pll", 747 "dsi2pllbyte", 748 "hdmipll"; 749 }; 750 751 l2cc: clock-controller@2011000 { 752 compatible = "qcom,kpss-gcc-apq8064", "qcom,kpss-gcc", "syscon"; 753 reg = <0x2011000 0x1000>; 754 clocks = <&gcc PLL8_VOTE>, <&pxo_board>; 755 clock-names = "pll8_vote", "pxo"; 756 #clock-cells = <0>; 757 }; 758 759 rpm: rpm@108000 { 760 compatible = "qcom,rpm-apq8064"; 761 reg = <0x108000 0x1000>; 762 qcom,ipc = <&l2cc 0x8 2>; 763 764 interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>, 765 <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>, 766 <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>; 767 interrupt-names = "ack", "err", "wakeup"; 768 769 rpmcc: clock-controller { 770 compatible = "qcom,rpmcc-apq8064", "qcom,rpmcc"; 771 #clock-cells = <1>; 772 clocks = <&pxo_board>, <&cxo_board>; 773 clock-names = "pxo", "cxo"; 774 }; 775 }; 776 777 usb1: usb@12500000 { 778 compatible = "qcom,ci-hdrc"; 779 reg = <0x12500000 0x200>, 780 <0x12500200 0x200>; 781 interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; 782 clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>; 783 clock-names = "core", "iface"; 784 assigned-clocks = <&gcc USB_HS1_XCVR_CLK>; 785 assigned-clock-rates = <60000000>; 786 resets = <&gcc USB_HS1_RESET>; 787 reset-names = "core"; 788 phy_type = "ulpi"; 789 ahb-burst-config = <0>; 790 phys = <&usb_hs1_phy>; 791 phy-names = "usb-phy"; 792 status = "disabled"; 793 #reset-cells = <1>; 794 795 ulpi { 796 usb_hs1_phy: phy { 797 compatible = "qcom,usb-hs-phy-apq8064", 798 "qcom,usb-hs-phy"; 799 clocks = <&sleep_clk>, <&cxo_board>; 800 clock-names = "sleep", "ref"; 801 resets = <&usb1 0>; 802 reset-names = "por"; 803 #phy-cells = <0>; 804 }; 805 }; 806 }; 807 808 usb3: usb@12520000 { 809 compatible = "qcom,ci-hdrc"; 810 reg = <0x12520000 0x200>, 811 <0x12520200 0x200>; 812 interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; 813 clocks = <&gcc USB_HS3_XCVR_CLK>, <&gcc USB_HS3_H_CLK>; 814 clock-names = "core", "iface"; 815 assigned-clocks = <&gcc USB_HS3_XCVR_CLK>; 816 assigned-clock-rates = <60000000>; 817 resets = <&gcc USB_HS3_RESET>; 818 reset-names = "core"; 819 phy_type = "ulpi"; 820 ahb-burst-config = <0>; 821 phys = <&usb_hs3_phy>; 822 phy-names = "usb-phy"; 823 status = "disabled"; 824 #reset-cells = <1>; 825 826 ulpi { 827 usb_hs3_phy: phy { 828 compatible = "qcom,usb-hs-phy-apq8064", 829 "qcom,usb-hs-phy"; 830 #phy-cells = <0>; 831 clocks = <&sleep_clk>, <&cxo_board>; 832 clock-names = "sleep", "ref"; 833 resets = <&usb3 0>; 834 reset-names = "por"; 835 }; 836 }; 837 }; 838 839 usb4: usb@12530000 { 840 compatible = "qcom,ci-hdrc"; 841 reg = <0x12530000 0x200>, 842 <0x12530200 0x200>; 843 interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>; 844 clocks = <&gcc USB_HS4_XCVR_CLK>, <&gcc USB_HS4_H_CLK>; 845 clock-names = "core", "iface"; 846 assigned-clocks = <&gcc USB_HS4_XCVR_CLK>; 847 assigned-clock-rates = <60000000>; 848 resets = <&gcc USB_HS4_RESET>; 849 reset-names = "core"; 850 phy_type = "ulpi"; 851 ahb-burst-config = <0>; 852 phys = <&usb_hs4_phy>; 853 phy-names = "usb-phy"; 854 status = "disabled"; 855 #reset-cells = <1>; 856 857 ulpi { 858 usb_hs4_phy: phy { 859 compatible = "qcom,usb-hs-phy-apq8064", 860 "qcom,usb-hs-phy"; 861 #phy-cells = <0>; 862 clocks = <&sleep_clk>, <&cxo_board>; 863 clock-names = "sleep", "ref"; 864 resets = <&usb4 0>; 865 reset-names = "por"; 866 }; 867 }; 868 }; 869 870 sata_phy0: phy@1b400000 { 871 compatible = "qcom,apq8064-sata-phy"; 872 status = "disabled"; 873 reg = <0x1b400000 0x200>; 874 clocks = <&gcc SATA_PHY_CFG_CLK>; 875 clock-names = "cfg"; 876 #phy-cells = <0>; 877 }; 878 879 sata0: sata@29000000 { 880 compatible = "qcom,apq8064-ahci", "generic-ahci"; 881 status = "disabled"; 882 reg = <0x29000000 0x180>; 883 interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; 884 885 clocks = <&gcc SFAB_SATA_S_H_CLK>, 886 <&gcc SATA_H_CLK>, 887 <&gcc SATA_A_CLK>, 888 <&gcc SATA_RXOOB_CLK>, 889 <&gcc SATA_PMALIVE_CLK>; 890 clock-names = "slave_iface", 891 "iface", 892 "core", 893 "rxoob", 894 "pmalive"; 895 896 assigned-clocks = <&gcc SATA_RXOOB_CLK>, 897 <&gcc SATA_PMALIVE_CLK>; 898 assigned-clock-rates = <100000000>, <100000000>; 899 900 phys = <&sata_phy0>; 901 phy-names = "sata-phy"; 902 ports-implemented = <0x1>; 903 }; 904 905 sdcc3: mmc@12180000 { 906 compatible = "arm,pl18x", "arm,primecell"; 907 arm,primecell-periphid = <0x00051180>; 908 status = "disabled"; 909 reg = <0x12180000 0x2000>; 910 interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; 911 clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; 912 clock-names = "mclk", "apb_pclk"; 913 bus-width = <4>; 914 cap-sd-highspeed; 915 cap-mmc-highspeed; 916 max-frequency = <192000000>; 917 no-1-8-v; 918 dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; 919 dma-names = "tx", "rx"; 920 }; 921 922 sdcc3bam: dma-controller@12182000 { 923 compatible = "qcom,bam-v1.3.0"; 924 reg = <0x12182000 0x8000>; 925 interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; 926 clocks = <&gcc SDC3_H_CLK>; 927 clock-names = "bam_clk"; 928 #dma-cells = <1>; 929 qcom,ee = <0>; 930 }; 931 932 sdcc4: mmc@121c0000 { 933 compatible = "arm,pl18x", "arm,primecell"; 934 arm,primecell-periphid = <0x00051180>; 935 status = "disabled"; 936 reg = <0x121c0000 0x2000>; 937 interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; 938 clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>; 939 clock-names = "mclk", "apb_pclk"; 940 bus-width = <4>; 941 cap-sd-highspeed; 942 cap-mmc-highspeed; 943 max-frequency = <48000000>; 944 dmas = <&sdcc4bam 2>, <&sdcc4bam 1>; 945 dma-names = "tx", "rx"; 946 pinctrl-names = "default"; 947 pinctrl-0 = <&sdc4_default_state>; 948 }; 949 950 sdcc4bam: dma-controller@121c2000 { 951 compatible = "qcom,bam-v1.3.0"; 952 reg = <0x121c2000 0x8000>; 953 interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; 954 clocks = <&gcc SDC4_H_CLK>; 955 clock-names = "bam_clk"; 956 #dma-cells = <1>; 957 qcom,ee = <0>; 958 }; 959 960 sdcc1: mmc@12400000 { 961 status = "disabled"; 962 compatible = "arm,pl18x", "arm,primecell"; 963 pinctrl-names = "default"; 964 pinctrl-0 = <&sdcc1_default_state>; 965 arm,primecell-periphid = <0x00051180>; 966 reg = <0x12400000 0x2000>; 967 interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; 968 clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; 969 clock-names = "mclk", "apb_pclk"; 970 bus-width = <8>; 971 max-frequency = <96000000>; 972 non-removable; 973 cap-sd-highspeed; 974 cap-mmc-highspeed; 975 dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; 976 dma-names = "tx", "rx"; 977 }; 978 979 sdcc1bam: dma-controller@12402000 { 980 compatible = "qcom,bam-v1.3.0"; 981 reg = <0x12402000 0x8000>; 982 interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; 983 clocks = <&gcc SDC1_H_CLK>; 984 clock-names = "bam_clk"; 985 #dma-cells = <1>; 986 qcom,ee = <0>; 987 }; 988 989 tcsr: syscon@1a400000 { 990 compatible = "qcom,tcsr-apq8064", "syscon"; 991 reg = <0x1a400000 0x100>; 992 }; 993 994 gpu: gpu@4300000 { 995 compatible = "qcom,adreno-320.2", "qcom,adreno"; 996 reg = <0x04300000 0x20000>; 997 reg-names = "kgsl_3d0_reg_memory"; 998 interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; 999 interrupt-names = "kgsl_3d0_irq"; 1000 clock-names = 1001 "core", 1002 "iface", 1003 "mem", 1004 "mem_iface"; 1005 clocks = 1006 <&mmcc GFX3D_CLK>, 1007 <&mmcc GFX3D_AHB_CLK>, 1008 <&mmcc GFX3D_AXI_CLK>, 1009 <&mmcc MMSS_IMEM_AHB_CLK>; 1010 1011 iommus = <&gfx3d 0 1012 &gfx3d 1 1013 &gfx3d 2 1014 &gfx3d 3 1015 &gfx3d 4 1016 &gfx3d 5 1017 &gfx3d 6 1018 &gfx3d 7 1019 &gfx3d 8 1020 &gfx3d 9 1021 &gfx3d 10 1022 &gfx3d 11 1023 &gfx3d 12 1024 &gfx3d 13 1025 &gfx3d 14 1026 &gfx3d 15 1027 &gfx3d 16 1028 &gfx3d 17 1029 &gfx3d 18 1030 &gfx3d 19 1031 &gfx3d 20 1032 &gfx3d 21 1033 &gfx3d 22 1034 &gfx3d 23 1035 &gfx3d 24 1036 &gfx3d 25 1037 &gfx3d 26 1038 &gfx3d 27 1039 &gfx3d 28 1040 &gfx3d 29 1041 &gfx3d 30 1042 &gfx3d 31 1043 &gfx3d1 0 1044 &gfx3d1 1 1045 &gfx3d1 2 1046 &gfx3d1 3 1047 &gfx3d1 4 1048 &gfx3d1 5 1049 &gfx3d1 6 1050 &gfx3d1 7 1051 &gfx3d1 8 1052 &gfx3d1 9 1053 &gfx3d1 10 1054 &gfx3d1 11 1055 &gfx3d1 12 1056 &gfx3d1 13 1057 &gfx3d1 14 1058 &gfx3d1 15 1059 &gfx3d1 16 1060 &gfx3d1 17 1061 &gfx3d1 18 1062 &gfx3d1 19 1063 &gfx3d1 20 1064 &gfx3d1 21 1065 &gfx3d1 22 1066 &gfx3d1 23 1067 &gfx3d1 24 1068 &gfx3d1 25 1069 &gfx3d1 26 1070 &gfx3d1 27 1071 &gfx3d1 28 1072 &gfx3d1 29 1073 &gfx3d1 30 1074 &gfx3d1 31>; 1075 1076 operating-points-v2 = <&gpu_opp_table>; 1077 1078 gpu_opp_table: opp-table { 1079 compatible = "operating-points-v2"; 1080 1081 opp-450000000 { 1082 opp-hz = /bits/ 64 <450000000>; 1083 }; 1084 1085 opp-27000000 { 1086 opp-hz = /bits/ 64 <27000000>; 1087 }; 1088 }; 1089 }; 1090 1091 mmss_sfpb: syscon@5700000 { 1092 compatible = "syscon"; 1093 reg = <0x5700000 0x70>; 1094 }; 1095 1096 dsi0: dsi@4700000 { 1097 compatible = "qcom,apq8064-dsi-ctrl", 1098 "qcom,mdss-dsi-ctrl"; 1099 #address-cells = <1>; 1100 #size-cells = <0>; 1101 interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; 1102 reg = <0x04700000 0x200>; 1103 reg-names = "dsi_ctrl"; 1104 1105 clocks = <&mmcc DSI_M_AHB_CLK>, 1106 <&mmcc DSI_S_AHB_CLK>, 1107 <&mmcc AMP_AHB_CLK>, 1108 <&mmcc DSI_CLK>, 1109 <&mmcc DSI1_BYTE_CLK>, 1110 <&mmcc DSI_PIXEL_CLK>, 1111 <&mmcc DSI1_ESC_CLK>; 1112 clock-names = "iface", "bus", "core_mmss", 1113 "src", "byte", "pixel", 1114 "core"; 1115 1116 assigned-clocks = <&mmcc DSI1_BYTE_SRC>, 1117 <&mmcc DSI1_ESC_SRC>, 1118 <&mmcc DSI_SRC>, 1119 <&mmcc DSI_PIXEL_SRC>; 1120 assigned-clock-parents = <&dsi0_phy 0>, 1121 <&dsi0_phy 0>, 1122 <&dsi0_phy 1>, 1123 <&dsi0_phy 1>; 1124 syscon-sfpb = <&mmss_sfpb>; 1125 phys = <&dsi0_phy>; 1126 status = "disabled"; 1127 1128 ports { 1129 #address-cells = <1>; 1130 #size-cells = <0>; 1131 1132 port@0 { 1133 reg = <0>; 1134 dsi0_in: endpoint { 1135 }; 1136 }; 1137 1138 port@1 { 1139 reg = <1>; 1140 dsi0_out: endpoint { 1141 }; 1142 }; 1143 }; 1144 }; 1145 1146 1147 dsi0_phy: phy@4700200 { 1148 compatible = "qcom,dsi-phy-28nm-8960"; 1149 #clock-cells = <1>; 1150 #phy-cells = <0>; 1151 1152 reg = <0x04700200 0x100>, 1153 <0x04700300 0x200>, 1154 <0x04700500 0x5c>; 1155 reg-names = "dsi_pll", "dsi_phy", "dsi_phy_regulator"; 1156 clock-names = "iface", "ref"; 1157 clocks = <&mmcc DSI_M_AHB_CLK>, 1158 <&pxo_board>; 1159 status = "disabled"; 1160 }; 1161 1162 dsi1: dsi@5800000 { 1163 compatible = "qcom,mdss-dsi-ctrl"; 1164 interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>; 1165 reg = <0x05800000 0x200>; 1166 reg-names = "dsi_ctrl"; 1167 1168 clocks = <&mmcc DSI2_M_AHB_CLK>, 1169 <&mmcc DSI2_S_AHB_CLK>, 1170 <&mmcc AMP_AHB_CLK>, 1171 <&mmcc DSI2_CLK>, 1172 <&mmcc DSI2_BYTE_CLK>, 1173 <&mmcc DSI2_PIXEL_CLK>, 1174 <&mmcc DSI2_ESC_CLK>; 1175 clock-names = "iface", 1176 "bus", 1177 "core_mmss", 1178 "src", 1179 "byte", 1180 "pixel", 1181 "core"; 1182 1183 assigned-clocks = <&mmcc DSI2_BYTE_SRC>, 1184 <&mmcc DSI2_ESC_SRC>, 1185 <&mmcc DSI2_SRC>, 1186 <&mmcc DSI2_PIXEL_SRC>; 1187 assigned-clock-parents = <&dsi1_phy 0>, 1188 <&dsi1_phy 0>, 1189 <&dsi1_phy 1>, 1190 <&dsi1_phy 1>; 1191 1192 syscon-sfpb = <&mmss_sfpb>; 1193 phys = <&dsi1_phy>; 1194 1195 #address-cells = <1>; 1196 #size-cells = <0>; 1197 1198 status = "disabled"; 1199 1200 ports { 1201 #address-cells = <1>; 1202 #size-cells = <0>; 1203 1204 port@0 { 1205 reg = <0>; 1206 dsi1_in: endpoint { 1207 }; 1208 }; 1209 1210 port@1 { 1211 reg = <1>; 1212 dsi1_out: endpoint { 1213 }; 1214 }; 1215 }; 1216 }; 1217 1218 1219 dsi1_phy: dsi-phy@5800200 { 1220 compatible = "qcom,dsi-phy-28nm-8960"; 1221 reg = <0x05800200 0x100>, 1222 <0x05800300 0x200>, 1223 <0x05800500 0x5c>; 1224 reg-names = "dsi_pll", 1225 "dsi_phy", 1226 "dsi_phy_regulator"; 1227 clock-names = "iface", 1228 "ref"; 1229 clocks = <&mmcc DSI2_M_AHB_CLK>, 1230 <&pxo_board>; 1231 #clock-cells = <1>; 1232 #phy-cells = <0>; 1233 1234 status = "disabled"; 1235 }; 1236 1237 mdp_port0: iommu@7500000 { 1238 compatible = "qcom,apq8064-iommu"; 1239 #iommu-cells = <1>; 1240 clock-names = 1241 "smmu_pclk", 1242 "iommu_clk"; 1243 clocks = 1244 <&mmcc SMMU_AHB_CLK>, 1245 <&mmcc MDP_AXI_CLK>; 1246 reg = <0x07500000 0x100000>; 1247 interrupts = 1248 <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>, 1249 <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; 1250 qcom,ncb = <2>; 1251 }; 1252 1253 mdp_port1: iommu@7600000 { 1254 compatible = "qcom,apq8064-iommu"; 1255 #iommu-cells = <1>; 1256 clock-names = 1257 "smmu_pclk", 1258 "iommu_clk"; 1259 clocks = 1260 <&mmcc SMMU_AHB_CLK>, 1261 <&mmcc MDP_AXI_CLK>; 1262 reg = <0x07600000 0x100000>; 1263 interrupts = 1264 <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>, 1265 <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; 1266 qcom,ncb = <2>; 1267 }; 1268 1269 gfx3d: iommu@7c00000 { 1270 compatible = "qcom,apq8064-iommu"; 1271 #iommu-cells = <1>; 1272 clock-names = 1273 "smmu_pclk", 1274 "iommu_clk"; 1275 clocks = 1276 <&mmcc SMMU_AHB_CLK>, 1277 <&mmcc GFX3D_AXI_CLK>; 1278 reg = <0x07c00000 0x100000>; 1279 interrupts = 1280 <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, 1281 <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; 1282 qcom,ncb = <3>; 1283 }; 1284 1285 gfx3d1: iommu@7d00000 { 1286 compatible = "qcom,apq8064-iommu"; 1287 #iommu-cells = <1>; 1288 clock-names = 1289 "smmu_pclk", 1290 "iommu_clk"; 1291 clocks = 1292 <&mmcc SMMU_AHB_CLK>, 1293 <&mmcc GFX3D_AXI_CLK>; 1294 reg = <0x07d00000 0x100000>; 1295 interrupts = 1296 <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>, 1297 <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>; 1298 qcom,ncb = <3>; 1299 }; 1300 1301 pcie: pcie@1b500000 { 1302 compatible = "qcom,pcie-apq8064"; 1303 reg = <0x1b500000 0x1000>, 1304 <0x1b502000 0x80>, 1305 <0x1b600000 0x100>, 1306 <0x0ff00000 0x100000>; 1307 reg-names = "dbi", "elbi", "parf", "config"; 1308 device_type = "pci"; 1309 linux,pci-domain = <0>; 1310 bus-range = <0x00 0xff>; 1311 num-lanes = <1>; 1312 #address-cells = <3>; 1313 #size-cells = <2>; 1314 ranges = <0x81000000 0x0 0x00000000 0x0fe00000 0x0 0x00100000>, /* I/O */ 1315 <0x82000000 0x0 0x08000000 0x08000000 0x0 0x07e00000>; /* mem */ 1316 interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; 1317 interrupt-names = "msi"; 1318 #interrupt-cells = <1>; 1319 interrupt-map-mask = <0 0 0 0x7>; 1320 interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ 1321 <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ 1322 <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ 1323 <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ 1324 clocks = <&gcc PCIE_A_CLK>, 1325 <&gcc PCIE_H_CLK>, 1326 <&gcc PCIE_PHY_REF_CLK>; 1327 clock-names = "core", "iface", "phy"; 1328 resets = <&gcc PCIE_ACLK_RESET>, 1329 <&gcc PCIE_HCLK_RESET>, 1330 <&gcc PCIE_POR_RESET>, 1331 <&gcc PCIE_PCI_RESET>, 1332 <&gcc PCIE_PHY_RESET>; 1333 reset-names = "axi", "ahb", "por", "pci", "phy"; 1334 status = "disabled"; 1335 1336 pcie@0 { 1337 device_type = "pci"; 1338 reg = <0x0 0x0 0x0 0x0 0x0>; 1339 bus-range = <0x01 0xff>; 1340 1341 #address-cells = <3>; 1342 #size-cells = <2>; 1343 ranges; 1344 }; 1345 }; 1346 1347 hdmi: hdmi-tx@4a00000 { 1348 compatible = "qcom,hdmi-tx-8960"; 1349 pinctrl-names = "default"; 1350 pinctrl-0 = <&hdmi_pinctrl>; 1351 reg = <0x04a00000 0x2f0>; 1352 reg-names = "core_physical"; 1353 interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; 1354 clocks = <&mmcc HDMI_APP_CLK>, 1355 <&mmcc HDMI_M_AHB_CLK>, 1356 <&mmcc HDMI_S_AHB_CLK>; 1357 clock-names = "core", 1358 "master_iface", 1359 "slave_iface"; 1360 1361 phys = <&hdmi_phy>; 1362 1363 status = "disabled"; 1364 1365 ports { 1366 #address-cells = <1>; 1367 #size-cells = <0>; 1368 1369 port@0 { 1370 reg = <0>; 1371 hdmi_in: endpoint { 1372 }; 1373 }; 1374 1375 port@1 { 1376 reg = <1>; 1377 hdmi_out: endpoint { 1378 }; 1379 }; 1380 }; 1381 }; 1382 1383 hdmi_phy: phy@4a00400 { 1384 compatible = "qcom,hdmi-phy-8960"; 1385 reg = <0x4a00400 0x60>, 1386 <0x4a00500 0x100>; 1387 reg-names = "hdmi_phy", 1388 "hdmi_pll"; 1389 1390 clocks = <&mmcc HDMI_S_AHB_CLK>; 1391 clock-names = "slave_iface"; 1392 #phy-cells = <0>; 1393 #clock-cells = <0>; 1394 1395 status = "disabled"; 1396 }; 1397 1398 mdp: display-controller@5100000 { 1399 compatible = "qcom,mdp4"; 1400 reg = <0x05100000 0xf0000>; 1401 interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; 1402 clocks = <&mmcc MDP_CLK>, 1403 <&mmcc MDP_AHB_CLK>, 1404 <&mmcc MDP_AXI_CLK>, 1405 <&mmcc MDP_LUT_CLK>, 1406 <&mmcc HDMI_TV_CLK>, 1407 <&mmcc MDP_TV_CLK>; 1408 clock-names = "core_clk", 1409 "iface_clk", 1410 "bus_clk", 1411 "lut_clk", 1412 "hdmi_clk", 1413 "tv_clk"; 1414 1415 iommus = <&mdp_port0 0 1416 &mdp_port0 2 1417 &mdp_port1 0 1418 &mdp_port1 2>; 1419 1420 ports { 1421 #address-cells = <1>; 1422 #size-cells = <0>; 1423 1424 port@0 { 1425 reg = <0>; 1426 mdp_lvds_out: endpoint { 1427 }; 1428 }; 1429 1430 port@1 { 1431 reg = <1>; 1432 mdp_dsi1_out: endpoint { 1433 }; 1434 }; 1435 1436 port@2 { 1437 reg = <2>; 1438 mdp_dsi2_out: endpoint { 1439 }; 1440 }; 1441 1442 port@3 { 1443 reg = <3>; 1444 mdp_dtv_out: endpoint { 1445 }; 1446 }; 1447 }; 1448 }; 1449 1450 riva: riva-pil@3200800 { 1451 compatible = "qcom,riva-pil"; 1452 1453 reg = <0x03200800 0x1000>, <0x03202000 0x2000>, <0x03204000 0x100>; 1454 reg-names = "ccu", "dxe", "pmu"; 1455 1456 interrupts-extended = <&intc GIC_SPI 199 IRQ_TYPE_EDGE_RISING>, 1457 <&wcnss_smsm 6 IRQ_TYPE_EDGE_RISING>; 1458 interrupt-names = "wdog", "fatal"; 1459 1460 memory-region = <&wcnss_mem>; 1461 1462 status = "disabled"; 1463 1464 iris { 1465 compatible = "qcom,wcn3660"; 1466 1467 clocks = <&cxo_board>; 1468 clock-names = "xo"; 1469 }; 1470 1471 smd-edge { 1472 interrupts = <GIC_SPI 198 IRQ_TYPE_EDGE_RISING>; 1473 1474 qcom,ipc = <&l2cc 8 25>; 1475 qcom,smd-edge = <6>; 1476 1477 label = "riva"; 1478 1479 wcnss { 1480 compatible = "qcom,wcnss"; 1481 qcom,smd-channels = "WCNSS_CTRL"; 1482 1483 qcom,mmio = <&riva>; 1484 1485 bluetooth { 1486 compatible = "qcom,wcnss-bt"; 1487 }; 1488 1489 wifi { 1490 compatible = "qcom,wcnss-wlan"; 1491 1492 interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>, 1493 <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>; 1494 interrupt-names = "tx", "rx"; 1495 1496 qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>; 1497 qcom,smem-state-names = "tx-enable", "tx-rings-empty"; 1498 }; 1499 }; 1500 }; 1501 }; 1502 1503 etb@1a01000 { 1504 compatible = "arm,coresight-etb10", "arm,primecell"; 1505 reg = <0x1a01000 0x1000>; 1506 1507 clocks = <&rpmcc RPM_QDSS_CLK>; 1508 clock-names = "apb_pclk"; 1509 1510 in-ports { 1511 port { 1512 etb_in: endpoint { 1513 remote-endpoint = <&replicator_out0>; 1514 }; 1515 }; 1516 }; 1517 }; 1518 1519 tpiu@1a03000 { 1520 compatible = "arm,coresight-tpiu", "arm,primecell"; 1521 reg = <0x1a03000 0x1000>; 1522 1523 clocks = <&rpmcc RPM_QDSS_CLK>; 1524 clock-names = "apb_pclk"; 1525 1526 in-ports { 1527 port { 1528 tpiu_in: endpoint { 1529 remote-endpoint = <&replicator_out1>; 1530 }; 1531 }; 1532 }; 1533 }; 1534 1535 replicator { 1536 compatible = "arm,coresight-static-replicator"; 1537 1538 clocks = <&rpmcc RPM_QDSS_CLK>; 1539 clock-names = "apb_pclk"; 1540 1541 out-ports { 1542 #address-cells = <1>; 1543 #size-cells = <0>; 1544 1545 port@0 { 1546 reg = <0>; 1547 replicator_out0: endpoint { 1548 remote-endpoint = <&etb_in>; 1549 }; 1550 }; 1551 port@1 { 1552 reg = <1>; 1553 replicator_out1: endpoint { 1554 remote-endpoint = <&tpiu_in>; 1555 }; 1556 }; 1557 }; 1558 1559 in-ports { 1560 port { 1561 replicator_in: endpoint { 1562 remote-endpoint = <&funnel_out>; 1563 }; 1564 }; 1565 }; 1566 }; 1567 1568 funnel@1a04000 { 1569 compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; 1570 reg = <0x1a04000 0x1000>; 1571 1572 clocks = <&rpmcc RPM_QDSS_CLK>; 1573 clock-names = "apb_pclk"; 1574 1575 in-ports { 1576 #address-cells = <1>; 1577 #size-cells = <0>; 1578 1579 /* 1580 * Not described input ports: 1581 * 2 - connected to STM component 1582 * 3 - not-connected 1583 * 6 - not-connected 1584 * 7 - not-connected 1585 */ 1586 port@0 { 1587 reg = <0>; 1588 funnel_in0: endpoint { 1589 remote-endpoint = <&etm0_out>; 1590 }; 1591 }; 1592 port@1 { 1593 reg = <1>; 1594 funnel_in1: endpoint { 1595 remote-endpoint = <&etm1_out>; 1596 }; 1597 }; 1598 port@4 { 1599 reg = <4>; 1600 funnel_in4: endpoint { 1601 remote-endpoint = <&etm2_out>; 1602 }; 1603 }; 1604 port@5 { 1605 reg = <5>; 1606 funnel_in5: endpoint { 1607 remote-endpoint = <&etm3_out>; 1608 }; 1609 }; 1610 }; 1611 1612 out-ports { 1613 port { 1614 funnel_out: endpoint { 1615 remote-endpoint = <&replicator_in>; 1616 }; 1617 }; 1618 }; 1619 }; 1620 1621 etm@1a1c000 { 1622 compatible = "arm,coresight-etm3x", "arm,primecell"; 1623 reg = <0x1a1c000 0x1000>; 1624 1625 clocks = <&rpmcc RPM_QDSS_CLK>; 1626 clock-names = "apb_pclk"; 1627 1628 cpu = <&cpu0>; 1629 1630 out-ports { 1631 port { 1632 etm0_out: endpoint { 1633 remote-endpoint = <&funnel_in0>; 1634 }; 1635 }; 1636 }; 1637 }; 1638 1639 etm@1a1d000 { 1640 compatible = "arm,coresight-etm3x", "arm,primecell"; 1641 reg = <0x1a1d000 0x1000>; 1642 1643 clocks = <&rpmcc RPM_QDSS_CLK>; 1644 clock-names = "apb_pclk"; 1645 1646 cpu = <&cpu1>; 1647 1648 out-ports { 1649 port { 1650 etm1_out: endpoint { 1651 remote-endpoint = <&funnel_in1>; 1652 }; 1653 }; 1654 }; 1655 }; 1656 1657 etm@1a1e000 { 1658 compatible = "arm,coresight-etm3x", "arm,primecell"; 1659 reg = <0x1a1e000 0x1000>; 1660 1661 clocks = <&rpmcc RPM_QDSS_CLK>; 1662 clock-names = "apb_pclk"; 1663 1664 cpu = <&cpu2>; 1665 1666 out-ports { 1667 port { 1668 etm2_out: endpoint { 1669 remote-endpoint = <&funnel_in4>; 1670 }; 1671 }; 1672 }; 1673 }; 1674 1675 etm@1a1f000 { 1676 compatible = "arm,coresight-etm3x", "arm,primecell"; 1677 reg = <0x1a1f000 0x1000>; 1678 1679 clocks = <&rpmcc RPM_QDSS_CLK>; 1680 clock-names = "apb_pclk"; 1681 1682 cpu = <&cpu3>; 1683 1684 out-ports { 1685 port { 1686 etm3_out: endpoint { 1687 remote-endpoint = <&funnel_in5>; 1688 }; 1689 }; 1690 }; 1691 }; 1692 }; 1693}; 1694#include "qcom-apq8064-pins.dtsi" 1695