xref: /titanic_41/usr/src/uts/common/sys/usb/hcd/openhci/ohcid.h (revision 9b58c2ad19d1f06f07604b0f61b7ff38f757c8fa)
1 /*
2  * CDDL HEADER START
3  *
4  * The contents of this file are subject to the terms of the
5  * Common Development and Distribution License (the "License").
6  * You may not use this file except in compliance with the License.
7  *
8  * You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
9  * or http://www.opensolaris.org/os/licensing.
10  * See the License for the specific language governing permissions
11  * and limitations under the License.
12  *
13  * When distributing Covered Code, include this CDDL HEADER in each
14  * file and include the License file at usr/src/OPENSOLARIS.LICENSE.
15  * If applicable, add the following below this CDDL HEADER, with the
16  * fields enclosed by brackets "[]" replaced with your own identifying
17  * information: Portions Copyright [yyyy] [name of copyright owner]
18  *
19  * CDDL HEADER END
20  */
21 /*
22  * Copyright 2009 Sun Microsystems, Inc.  All rights reserved.
23  * Use is subject to license terms.
24  */
25 
26 #ifndef _SYS_USB_OHCID_H
27 #define	_SYS_USB_OHCID_H
28 
29 #ifdef	__cplusplus
30 extern "C" {
31 #endif
32 
33 /*
34  * Open Host Controller Driver (OHCI)
35  *
36  * The USB Open Host Controller driver is a software driver which interfaces
37  * to the Universal Serial Bus layer (USBA) and the USB Open Host Controller.
38  * The interface to USB Open Host Controller is defined by the OpenHCI  Host
39  * Controller Interface.
40  *
41  * This header file describes the data structures required for the USB Open
42  * Host Controller Driver to maintain state of USB Open Host Controller, to
43  * perform different USB transfers and for the bandwidth allocations.
44  */
45 
46 #include <sys/usb/hcd/openhci/ohci.h>
47 #include <sys/usb/hcd/openhci/ohci_hub.h>
48 
49 /*
50  * OpenHCI interrupt status information structure
51  *
52  * The Host Controller Driver (HCD) has to maintain two different sets of
53  * Host Controller (HC) state information that includes HC registers, the
54  * interrupt tables etc.. for the normal and polled modes.  In	addition,
55  * suppose if we switched to polled mode while ohci  interrupt handler is
56  * executing in the normal mode then we need to save the interrupt status
57  * information that includes interrupts for which ohci interrupt  handler
58  * is called and HCCA done head list in the polled mode. This infromation
59  * will be used later in normal mode to  service those missed interrupts.
60  * This will avoid race conditions like missing of normal mode's ohci SOF
61  * and WriteDoneHead interrupts because of this polled switch.
62  */
63 typedef struct ohci_save_intr_sts {
64 	/*
65 	 * The following field has set of flags & these flags will be set
66 	 * in the ohci interrupt handler to indicate that currently  ohci
67 	 * interrupt handler is in execution and also while critical code
68 	 * execution within the ohci interrupt handler.  These flags will
69 	 * be verified in polled mode while saving the normal mode's ohci
70 	 * interrupt status information.
71 	 */
72 	uint_t		ohci_intr_flag;		/* Intr handler flags */
73 
74 	/*
75 	 * The following fields will be used to save the interrupt status
76 	 * and the HCCA done head list that the ohci interrupt handler is
77 	 * currently handling.
78 	 */
79 	uint_t		ohci_curr_intr_sts;	/* Current interrupts */
80 	ohci_td_t	*ohci_curr_done_lst;	/* Current done head  */
81 
82 	/*
83 	 * The following fields will be used to save the interrupt status
84 	 * and the HCCA done list currently being handled by the critical
85 	 * section of the ohci interrupt handler..
86 	 */
87 	uint_t		ohci_critical_intr_sts;	/* Critical interrupts */
88 	ohci_td_t	*ohci_critical_done_lst; /* Critical done head */
89 
90 	/*
91 	 * The following fields will be used to save the interrupt status
92 	 * and HCCA done head list by the polled code if an  interrupt is
93 	 * pending when polled code is entered. These missed interrupts &
94 	 * done list will be serviced either in current  normal mode ohci
95 	 * interrupt handler execution or during the next  ohci interrupt
96 	 * handler execution.
97 	 */
98 	uint_t		ohci_missed_intr_sts;	/* Missed interrupts */
99 	ohci_td_t	*ohci_missed_done_lst;	/* Missed done head  */
100 } ohci_save_intr_sts_t;
101 
102 /*
103  * These flags will be set in the the normal mode ohci	interrupt handler
104  * to indicate that currently ohci interrupt handler is in  execution and
105  * also while critical code  execution within the ohci interrupt handler.
106  * These flags will be verified in the polled mode while saving the normal
107  * mode's ohci interrupt status infromation.
108  */
109 #define		OHCI_INTR_HANDLING	0x01	/* Handling ohci intrs */
110 #define		OHCI_INTR_CRITICAL	0x02	/* Critical intr code  */
111 
112 
113 /*
114  * OpenHCI Host Controller state structure
115  *
116  * The Host Controller Driver (HCD) maintains the state of Host Controller
117  * (HC). There is an ohci_state structure per instance	of the OpenHCI
118  * host controller.
119  */
120 
121 typedef struct ohci_state {
122 	dev_info_t		*ohci_dip;		/* Dip of HC */
123 	uint_t			ohci_instance;
124 	usba_hcdi_ops_t		*ohci_hcdi_ops;		/* HCDI structure */
125 	uint_t			ohci_flags;		/* Used for cleanup */
126 	uint16_t		ohci_vendor_id;		/* chip vendor */
127 	uint16_t		ohci_device_id;		/* chip device */
128 	uint8_t			ohci_rev_id;		/* chip revison */
129 
130 	ohci_regs_t		*ohci_regsp;		/* Host ctlr regs */
131 	ddi_acc_handle_t	ohci_regs_handle;	/* Reg handle */
132 
133 	ddi_acc_handle_t	ohci_config_handle;	/* Config space hndle */
134 	uint_t			ohci_frame_interval;	/* Frme inter reg */
135 	ddi_dma_attr_t		ohci_dma_attr;		/* DMA attributes */
136 
137 	ddi_intr_handle_t	*ohci_htable;		/* intr handle */
138 	int			ohci_intr_type;		/* intr type used */
139 	int			ohci_intr_cnt;		/* # of intrs inuse */
140 	uint_t			ohci_intr_pri;		/* intr priority */
141 	int			ohci_intr_cap;		/* intr capabilities */
142 	boolean_t		ohci_msi_enabled;	/* default to true */
143 	kmutex_t		ohci_int_mutex;		/* Mutex for struct */
144 
145 	/* HCCA area */
146 	ohci_hcca_t		*ohci_hccap;		/* Virtual HCCA ptr */
147 	ddi_dma_cookie_t	ohci_hcca_cookie;	/* DMA cookie */
148 	ddi_dma_handle_t	ohci_hcca_dma_handle;	/* DMA handle */
149 	ddi_acc_handle_t	ohci_hcca_mem_handle;	/* Memory handle */
150 
151 	/*
152 	 * There are two pools of memory. One pool contains the memory for
153 	 * the transfer descriptors and other pool contains the memory for
154 	 * the endpoint descriptors. The advantage of the pools is that it's
155 	 * easy to go back and forth between the iommu and the cpu addresses.
156 	 *
157 	 * The pools are protected by the ohci_int_mutex because the memory
158 	 * in the pools may be accessed by either the host controller or the
159 	 * host controller driver.
160 	 */
161 
162 	/* General transfer descriptor pool */
163 	ohci_td_t		*ohci_td_pool_addr;	/* Start of the pool */
164 	ddi_dma_cookie_t	ohci_td_pool_cookie;	/* DMA cookie */
165 	ddi_dma_handle_t	ohci_td_pool_dma_handle;	/* DMA hndle */
166 	ddi_acc_handle_t	ohci_td_pool_mem_handle;	/* Mem hndle */
167 
168 	/* Endpoint descriptor pool */
169 	ohci_ed_t		*ohci_ed_pool_addr;	/* Start of the pool */
170 	ddi_dma_cookie_t	ohci_ed_pool_cookie;	/* DMA cookie */
171 	ddi_dma_handle_t	ohci_ed_pool_dma_handle;	/* DMA handle */
172 	ddi_acc_handle_t	ohci_ed_pool_mem_handle;	/* Mem handle */
173 	uint_t			ohci_dma_addr_bind_flag;	/* DMA flag */
174 
175 	/* Condition variables */
176 	kcondvar_t		ohci_SOF_cv;		/* SOF variable */
177 
178 	/* Semaphore to serialize opens and closes */
179 	ksema_t			ohci_ocsem;
180 
181 	/*
182 	 * Bandwidth fields
183 	 *
184 	 * The ohci_bandwidth array keeps track of the allocated bandwidth
185 	 * for this host controller. The total bandwidth allocated for least
186 	 * allocated list out of the 32 periodic lists is represented by the
187 	 * ohci_periodic_minimum_bandwidth field.
188 	 */
189 	uint_t			ohci_periodic_minimum_bandwidth;
190 	uint_t			ohci_periodic_bandwidth[NUM_INTR_ED_LISTS];
191 
192 	/* Different transfer open pipe counts */
193 	uint_t			ohci_open_pipe_count;
194 	uint_t			ohci_open_ctrl_pipe_count;
195 	uint_t			ohci_open_bulk_pipe_count;
196 	uint_t			ohci_open_periodic_pipe_count;
197 	uint_t			ohci_open_isoch_pipe_count;
198 	/*
199 	 * Endpoint Reclamation List
200 	 *
201 	 * The interrupt or isochronous list processing cannot be stopped
202 	 * when a periodic endpoint is removed from the list. The endpoints
203 	 * are detached from the interrupt lattice tree and put on to the
204 	 * reclaimation list. On next SOF interrupt all those endpoints,
205 	 * which are on the reclaimation list will be deallocated.
206 	 */
207 	ohci_ed_t		*ohci_reclaim_list;	/* Reclaimation list */
208 
209 	ohci_root_hub_t		ohci_root_hub;		/* Root hub info */
210 
211 	/*
212 	 * Global transfer timeout handling & this transfer timeout handling
213 	 * will be per USB Host Controller.
214 	 */
215 	struct ohci_trans_wrapper *ohci_timeout_list;	/* Timeout List */
216 	timeout_id_t		ohci_timer_id;		/* Timer id  */
217 
218 	/* Frame number overflow information */
219 	usb_frame_number_t	ohci_fno;
220 
221 	/* For Schedule Overrun error counter */
222 	uint_t			ohci_so_error;
223 
224 	/* For host controller error counter */
225 	uint_t			ohci_hc_error;
226 
227 	/* For SOF interrupt event */
228 	boolean_t		ohci_sof_flag;
229 
230 	/* Openhci Host Controller Software State information */
231 	uint_t			ohci_hc_soft_state;
232 
233 	/*
234 	 * ohci_save_intr_stats is used to save the normal mode interrupt
235 	 * status information while executing interrupt handler & also by
236 	 * the polled code if an interrupt is pending for the normal mode
237 	 * when polled code is entered.
238 	 */
239 	ohci_save_intr_sts_t	ohci_save_intr_sts;
240 
241 	/*
242 	 * Saved copy of the ohci registers of the normal mode & change
243 	 * required ohci registers values for the polled mode operation.
244 	 * Before returning from the polled mode to normal mode replace
245 	 * the required current registers with this saved ohci registers
246 	 * copy.
247 	 */
248 	ohci_regs_t	ohci_polled_save_regs;
249 
250 	/*
251 	 * Saved copy of the interrupt table used in normal ohci mode and
252 	 * replace this table by another interrupt table that used in the
253 	 * POLLED mode.
254 	 */
255 	ohci_ed_t	*ohci_polled_save_IntTble[NUM_INTR_ED_LISTS];
256 
257 	/* ohci polled mode enter counter for the input devices */
258 	uint_t			ohci_polled_enter_count;
259 
260 	/*
261 	 * Counter for polled mode and used in suspend mode to see if
262 	 * there is a input device connected.
263 	 */
264 	uint_t			ohci_polled_kbd_count;
265 
266 	/* Done list for the Polled mode */
267 	ohci_td_t		*ohci_polled_done_list;
268 
269 	/* Log handle for debug, console, log messages */
270 	usb_log_handle_t	ohci_log_hdl;
271 
272 	/* Kstat structures */
273 	kstat_t			*ohci_intrs_stats;
274 	kstat_t			*ohci_total_stats;
275 	kstat_t			*ohci_count_stats[USB_N_COUNT_KSTATS];
276 } ohci_state_t;
277 
278 typedef struct ohci_intrs_stats {
279 	struct kstat_named	ohci_hcr_intr_so;
280 	struct kstat_named	ohci_hcr_intr_wdh;
281 	struct kstat_named	ohci_hcr_intr_sof;
282 	struct kstat_named	ohci_hcr_intr_rd;
283 	struct kstat_named	ohci_hcr_intr_ue;
284 	struct kstat_named	ohci_hcr_intr_fno;
285 	struct kstat_named	ohci_hcr_intr_rhsc;
286 	struct kstat_named	ohci_hcr_intr_oc;
287 	struct kstat_named	ohci_hcr_intr_not_claimed;
288 	struct kstat_named	ohci_hcr_intr_total;
289 } ohci_intrs_stats_t;
290 
291 /*
292  * ohci kstat defines
293  */
294 #define	OHCI_INTRS_STATS(ohci)	((ohci)->ohci_intrs_stats)
295 #define	OHCI_INTRS_STATS_DATA(ohci)	\
296 	((ohci_intrs_stats_t *)OHCI_INTRS_STATS((ohci))->ks_data)
297 
298 #define	OHCI_TOTAL_STATS(ohci)	((ohci)->ohci_total_stats)
299 #define	OHCI_TOTAL_STATS_DATA(ohci)	(KSTAT_IO_PTR((ohci)->ohci_total_stats))
300 #define	OHCI_CTRL_STATS(ohci)	\
301 	(KSTAT_IO_PTR((ohci)->ohci_count_stats[USB_EP_ATTR_CONTROL]))
302 #define	OHCI_BULK_STATS(ohci)	\
303 	(KSTAT_IO_PTR((ohci)->ohci_count_stats[USB_EP_ATTR_BULK]))
304 #define	OHCI_INTR_STATS(ohci)	\
305 	(KSTAT_IO_PTR((ohci)->ohci_count_stats[USB_EP_ATTR_INTR]))
306 #define	OHCI_ISOC_STATS(ohci)	\
307 	(KSTAT_IO_PTR((ohci)->ohci_count_stats[USB_EP_ATTR_ISOCH]))
308 
309 /* warlock directives, stable data */
310 _NOTE(MUTEX_PROTECTS_DATA(ohci_state_t::ohci_int_mutex, ohci_state_t))
311 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_intr_pri))
312 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_dip))
313 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_regsp))
314 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_instance))
315 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_vendor_id))
316 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_device_id))
317 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_rev_id))
318 
319 /* this may not be stable data in the future */
320 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_td_pool_addr))
321 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_td_pool_mem_handle))
322 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_ed_pool_addr))
323 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_ed_pool_mem_handle))
324 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_td_pool_cookie))
325 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_ed_pool_cookie))
326 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_hcca_mem_handle))
327 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_hccap))
328 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_dma_addr_bind_flag))
329 _NOTE(DATA_READABLE_WITHOUT_LOCK(ohci_state_t::ohci_log_hdl))
330 
331 _NOTE(LOCK_ORDER(ohci_state::ohci_int_mutex \
332 		usba_pipe_handle_data::p_mutex \
333 		usba_device::usb_mutex \
334 		usba_ph_impl::usba_ph_mutex))
335 
336 /*
337  * Host Contoller Software States
338  *
339  * OHCI_CTLR_INIT_STATE:
340  *	The host controller soft state will be set to this during the
341  *	ohci_attach.
342  *
343  * OHCI_CTLR_SUSPEND_STATE:
344  *	The host controller soft state will be set to this during the
345  *	ohci_cpr_suspend.
346  *
347  * OHCI_CTLR_OPERATIONAL_STATE:
348  *	The host controller soft state will be set to this after moving
349  *	host controller to operational state and host controller start
350  *	generating SOF successfully.
351  *
352  * OHCI_CTLR_ERROR_STATE:
353  *	The host controller soft state will be set to this during the
354  *	no SOF or UE error conditions.
355  *
356  *	Under this state or condition, only pipe stop polling, pipe reset
357  *	and pipe close are allowed. But all other entry points like  pipe
358  *	open, get/set pipe policy, cotrol send/receive, bulk send/receive
359  *	isoch send/receive, start polling etc. will fail.
360  *
361  * State Diagram for the host controller software state
362  *
363  *
364  * ohci_attach->[INIT_STATE]
365  *	|
366  *	|	-------->----[ERROR_STATE]--<-----------<---
367  *	|      |      Failure (UE/no SOF condition)	    |
368  *	|      ^					    ^
369  *	V      |      Success				    |
370  * ohci_init_ctlr--->--------[OPERATIONAL_STATE]------>-ohci_send/recv/polling
371  *	^					    |
372  *	|					    |
373  *	|					    V
374  *	-<-ohci_cpr_resume--[SUSPEND_STATE]-<-ohci_cpr_suspend
375  */
376 #define	OHCI_CTLR_INIT_STATE		0	/* Initilization state */
377 #define	OHCI_CTLR_SUSPEND_STATE		1	/* Suspend state */
378 #define	OHCI_CTLR_OPERATIONAL_STATE	2	/* Operational state */
379 #define	OHCI_CTLR_ERROR_STATE		3	/* Ue error or no sof state */
380 
381 /*
382  * Define all ohci's Vendor-id and Device-id Here
383  */
384 #define	RIO_VENDOR	0x108e
385 #define	RIO_DEVICE	0x1103
386 #define	OHCI_IS_RIO(ohcip)	(ohcip->ohci_vendor_id == RIO_VENDOR)
387 
388 /*
389  * Periodic and non-periodic macros
390  */
391 #define	OHCI_PERIODIC_ENDPOINT(endpoint) (((endpoint->bmAttributes &\
392 				USB_EP_ATTR_MASK) == USB_EP_ATTR_INTR) ||\
393 				((endpoint->bmAttributes &\
394 				USB_EP_ATTR_MASK) == USB_EP_ATTR_ISOCH))
395 
396 #define	OHCI_NON_PERIODIC_ENDPOINT(endpoint) (((endpoint->bmAttributes &\
397 				USB_EP_ATTR_MASK) == USB_EP_ATTR_CONTROL) ||\
398 				((endpoint->bmAttributes &\
399 				USB_EP_ATTR_MASK) == USB_EP_ATTR_BULK))
400 
401 /*
402  * OHCI ED and TD Pool sizes.
403  */
404 #define	OHCI_ED_POOL_SIZE	100
405 #define	OHCI_TD_POOL_SIZE	200
406 
407 /*
408  * ohci_dma_addr_bind_flag values
409  *
410  * This flag indicates if the various DMA addresses allocated by the OHCI
411  * have been bound to their respective handles. This is needed to recover
412  * without errors from ohci_cleanup when it calls ddi_dma_unbind_handle()
413  */
414 #define	OHCI_TD_POOL_BOUND	0x01	/* For TD pools  */
415 #define	OHCI_ED_POOL_BOUND	0x02	/* For ED pools  */
416 #define	OHCI_HCCA_DMA_BOUND	0x04	/* For HCCA area */
417 
418 /*
419  * Maximum SOF wait count
420  */
421 #define	MAX_SOF_WAIT_COUNT	2	/* Wait for maximum SOF frames */
422 
423 
424 /*
425  * Pipe private structure
426  *
427  * There is an instance of this structure per pipe.  This structure holds
428  * HCD specific pipe information.  A pointer to this structure is kept in
429  * the USBA pipe handle (usba_pipe_handle_data_t).
430  */
431 typedef struct ohci_pipe_private {
432 	usba_pipe_handle_data_t	*pp_pipe_handle;	/* Back ptr to handle */
433 	ohci_ed_t		*pp_ept;		/* Pipe's ept */
434 
435 	/* State of the pipe */
436 	uint_t			pp_state;		/* See below */
437 
438 	/* Local copy of the pipe policy */
439 	usb_pipe_policy_t	pp_policy;
440 
441 	/* For Periodic Pipes Only */
442 	uint_t			pp_node;		/* Node in lattice */
443 	uint_t			pp_cur_periodic_req_cnt; /* Curr req count */
444 	uint_t			pp_max_periodic_req_cnt; /* Max req count */
445 
446 	/* For isochronous pipe only */
447 	usb_frame_number_t	pp_next_frame_number;	/* Next frame no */
448 
449 	/*
450 	 * Each pipe may have multiple transfer wrappers. Each transfer
451 	 * wrapper represents a USB transfer on the bus.  A transfer is
452 	 * made up of one or more transactions.
453 	 */
454 	struct ohci_trans_wrapper *pp_tw_head;	/* Head of the list */
455 	struct ohci_trans_wrapper *pp_tw_tail;	/* Tail of the list */
456 
457 	/* Done td count */
458 	uint_t			pp_count_done_tds;	/* Done td count */
459 
460 	/* Errors */
461 	usb_cr_t		pp_error;		/* Pipe error */
462 
463 	/* Flags */
464 	uint_t			pp_flag;		/* Flags */
465 
466 	/* Condition variable for transfers completion event */
467 	kcondvar_t		pp_xfer_cmpl_cv;	/* Xfer completion */
468 
469 	/*
470 	 * HCD gets Interrupt/Isochronous IN polling request only once and
471 	 * it has to insert next polling requests after completion of first
472 	 * request until either stop polling/pipe close is called. So  HCD
473 	 * has to take copy of the original Interrupt/Isochronous IN request.
474 	 */
475 	usb_opaque_t		pp_client_periodic_in_reqp;
476 } ohci_pipe_private_t;
477 
478 /* warlock directives, stable data */
479 _NOTE(MUTEX_PROTECTS_DATA(ohci_state_t::ohci_int_mutex, ohci_pipe_private_t))
480 
481 /*
482  * Pipe states
483  *
484  * ohci pipe states will be similar to usba. Refer usbai.h.
485  */
486 #define	OHCI_PIPE_STATE_IDLE		1	/* Pipe is in ready state */
487 #define	OHCI_PIPE_STATE_ACTIVE		2	/* Pipe is in busy state */
488 #define	OHCI_PIPE_STATE_ERROR		3	/* Pipe is in error state */
489 
490 /* Additional ohci pipe states for the ohci_pipe_cleanup */
491 #define	OHCI_PIPE_STATE_CLOSE		4	/* Pipe close */
492 #define	OHCI_PIPE_STATE_RESET		5	/* Pipe reset */
493 #define	OHCI_PIPE_STATE_STOP_POLLING	6	/* Pipe stop polling */
494 
495 /*
496  * Pipe specific Flags
497  */
498 #define	OHCI_ISOC_XFER_CONTINUE	1	/* For isoc transfers */
499 
500 /*
501  * The maximum allowable usb isochronous data transfer size or maximum
502  * number of isochronous data packets.
503  *
504  * Each usb isochronous request must not exceed multiples of isochronous
505  * endpoint packet size and OHCI_MAX_ISOC_PKTS_PER_XFER.
506  *
507  * Ex: usb isochronous endpoint maximum packet size is 64 bytes
508  *     maximum usb isochronous request will be OHCI_MAX_ISOC_PKTS_PER_XFER
509  *     * 64 bytes
510  */
511 #define		OHCI_MAX_ISOC_PKTS_PER_XFER	256	/* Max pkts per req */
512 
513 /*
514  * The ohci supports maximum of eight isochronous data packets per transfer
515  * descriptor.
516  */
517 #define		OHCI_ISOC_PKTS_PER_TD		8	/* Packets per TD */
518 
519 /*
520  * USB frame offset
521  *
522  * Add appropriate frame offset to the current usb frame number and use it
523  * as a starting frame number for a given usb isochronous request.
524  */
525 #define		OHCI_FRAME_OFFSET		2	/* Frame offset */
526 
527 /*
528  * Default usb isochronous receive packets per request before ohci will do
529  * callback.
530  */
531 #define		OHCI_DEFAULT_ISOC_RCV_PKTS	1	/* isoc pkts per req */
532 
533 /*
534  * Different interrupt polling intervals supported
535  */
536 #define		INTR_1MS_POLL	1
537 #define		INTR_2MS_POLL	2
538 #define		INTR_4MS_POLL	4
539 #define		INTR_8MS_POLL	8
540 #define		INTR_16MS_POLL	16
541 #define		INTR_32MS_POLL	32
542 
543 /*
544  * Number of interrupt/isochronous transfer requests that should
545  * be maintained on the interrupt/isochronous endpoint corresponding
546  * to different polling intervals supported.
547  */
548 #define		INTR_1MS_REQS	4	/* 1ms polling interval */
549 #define		INTR_2MS_REQS	2	/* 2ms polling interval */
550 #define		INTR_XMS_REQS	1	/* Between 4ms and 32ms */
551 
552 /* Function prototype */
553 typedef void (*ohci_handler_function_t)(
554 	ohci_state_t			*ohcip,
555 	ohci_pipe_private_t		*pp,
556 	struct ohci_trans_wrapper	*tw,
557 	ohci_td_t			*td,
558 	void				*ohci_handle_callback_value);
559 
560 
561 /*
562  * Transfer wrapper
563  *
564  * The transfer wrapper represents a USB transfer on the bus and there
565  * is one instance per USB transfer.  A transfer is made up of one or
566  * more transactions. OHCI uses one TD for one transaction. So one
567  * transfer wrapper may have one or more TDs associated.
568  *
569  * Control and bulk pipes will have one transfer wrapper per transfer
570  * and where as Isochronous and Interrupt pipes will only have one
571  * transfer wrapper. The transfers wrapper are continually reused for
572  * the Interrupt and Isochronous pipes as those pipes are polled.
573  *
574  * Control, bulk and interrupt transfers will have one DMA buffer per
575  * transfer. The data to be transferred are contained in the DMA buffer
576  * which is virtually contiguous but physically discontiguous. When
577  * preparing the TDs for a USB transfer, the DMA cookies contained in
578  * the buffer need to be walked through to retrieve the DMA addresses.
579  *
580  * Isochronous transfers may have multiple DMA buffers per transfer
581  * with each isoc TD having a DMA buffer. And one isoc TD may hold up to
582  * eight isoc packets, but two cookies at most.
583  */
584 typedef struct ohci_trans_wrapper {
585 	struct ohci_trans_wrapper	*tw_next;	/* Next wrapper */
586 	ohci_pipe_private_t		*tw_pipe_private; /* Back ptr */
587 	ddi_dma_handle_t		tw_dmahandle;	/* DMA handle */
588 	ddi_acc_handle_t		tw_accesshandle; /* Acc hndle */
589 	ddi_dma_cookie_t		tw_cookie;	/* DMA cookie */
590 	uint32_t			tw_id;		/* 32bit ID */
591 	size_t				tw_length;	/* Txfer length */
592 	char				*tw_buf;	/* Buffer for Xfer */
593 	uint_t				tw_ncookies;	/* DMA cookie count */
594 	uint_t				tw_cookie_idx;	/* DMA cookie index */
595 	size_t				tw_dma_offs;	/* DMA buffer offset */
596 	usb_flags_t			tw_flags;	/* Flags */
597 	uint_t				tw_num_tds;	/* Number of TDs */
598 	ohci_td_t			*tw_hctd_head;	/* Head TD */
599 	ohci_td_t			*tw_hctd_tail;	/* Tail TD */
600 	uint_t				tw_direction;	/* Direction of TD */
601 	uint_t				tw_pkt_idx;	/* packet index */
602 
603 	/* We preallocate all the td's for each tw and place them here */
604 	ohci_td_t			*tw_hctd_free_list;
605 
606 	/* Current transfer request pointer */
607 	usb_opaque_t			tw_curr_xfer_reqp;
608 
609 	/* Current isochronous packet descriptor pointer */
610 	usb_isoc_pkt_descr_t		*tw_curr_isoc_pktp;
611 
612 	/* Isochronous DMA handlers and buffer pointers are stored here */
613 	ohci_isoc_buf_t			*tw_isoc_bufs;
614 	size_t				tw_isoc_strtlen;
615 
616 	/* Transfer timeout information */
617 	uint_t				tw_timeout;	/* Timeout value */
618 	struct ohci_trans_wrapper	*tw_timeout_next; /* Xfer Timeout Q */
619 
620 	/*
621 	 * This is the function to call when this td is done. This way
622 	 * we don't have to look in the td to figure out what kind it is.
623 	 */
624 	ohci_handler_function_t		tw_handle_td;
625 
626 	/*
627 	 * This is the callback value used when processing a done td.
628 	 */
629 	usb_opaque_t			tw_handle_callback_value;
630 } ohci_trans_wrapper_t;
631 
632 _NOTE(MUTEX_PROTECTS_DATA(ohci_state_t::ohci_int_mutex, ohci_trans_wrapper))
633 
634 
635 /*
636  * Time waits for the different OHCI specific operations.
637  * These timeout values are specified in terms of microseconds.
638  */
639 #define	OHCI_RESET_TIMEWAIT	10000	/* HC reset waiting time */
640 #define	OHCI_RESUME_TIMEWAIT	40000	/* HC resume waiting time */
641 #define	OHCI_TIMEWAIT		10000	/* HC any other waiting time */
642 
643 /* These timeout values are specified in seconds */
644 #define	OHCI_DEFAULT_XFER_TIMEOUT	5 /* Default transfer timeout */
645 #define	OHCI_MAX_SOF_TIMEWAIT		3 /* Maximum SOF waiting time */
646 #define	OHCI_XFER_CMPL_TIMEWAIT		3 /* Xfers completion timewait */
647 
648 /* OHCI flags for general use */
649 #define	OHCI_FLAGS_NOSLEEP	0x000	/* Don't wait for SOF */
650 #define	OHCI_FLAGS_SLEEP	0x100	/* Wait for SOF */
651 #define	OHCI_FLAGS_DMA_SYNC	0x200	/* Call ddi_dma_sync */
652 
653 /*
654  * Maximum allowable data transfer  size per transaction as supported
655  * by OHCI is 8k. (See Open Host Controller Interface Spec rev 1.0a)
656  */
657 #define	OHCI_MAX_TD_XFER_SIZE	0x2000	/* Maxmum data per transaction */
658 
659 /*
660  * One OHCI TD allows two physically discontiguous pages. The page size
661  * is 4k.
662  */
663 #define	OHCI_MAX_TD_BUF_SIZE	0x1000
664 
665 /*
666  * The maximum allowable bulk data transfer size. It can be different
667  * from OHCI_MAX_TD_XFER_SIZE and if it is more then ohci driver will
668  * take care of  breaking a bulk data request into  multiples of ohci
669  * OHCI_MAX_TD_XFER_SIZE  until request is satisfied.  Currently this
670  * value is set to 256k bytes.
671  */
672 #define	OHCI_MAX_BULK_XFER_SIZE	0x40000	/* Maximum bulk transfer size */
673 
674 /*
675  * Timeout flags
676  *
677  * These flags will be used to stop the timer before timeout handler
678  * gets executed.
679  */
680 #define	OHCI_REMOVE_XFER_IFLAST	1	/* Stop the timer if  it is last TD */
681 #define	OHCI_REMOVE_XFER_ALWAYS	2	/* Stop the timer without condition */
682 
683 
684 /*
685  * Bandwidth allocation
686  *
687  * The following definitions are  used during  bandwidth calculations
688  * for a given endpoint maximum packet size.
689  */
690 #define	MAX_USB_BUS_BANDWIDTH	1500	/* Up to 1500 bytes per frame */
691 #define	MAX_POLL_INTERVAL	255	/* Maximum polling interval */
692 #define	MIN_POLL_INTERVAL	1	/* Minimum polling interval */
693 #define	SOF			6	/* Length in bytes of SOF */
694 #define	EOF			4	/* Length in bytes of EOF */
695 #define	TREE_HEIGHT		5	/* Log base 2 of 32 */
696 
697 /*
698  * Minimum polling interval for low speed endpoint
699  *
700  * According USB Specifications, a full-speed endpoint can specify
701  * a desired polling interval 1ms to 255ms and a low speed endpoints
702  * are limited to specifying only 10ms to 255ms. But some old keyboards
703  * and mice uses polling interval of 8ms. For compatibility purpose,
704  * we are using polling interval between 8ms and 255ms for low speed
705  * endpoints. But ohci driver will reject any low speed endpoints which
706  * request polling interval less than 8ms.
707  */
708 #define	MIN_LOW_SPEED_POLL_INTERVAL	8
709 
710 /*
711  * For non-periodic transfers, reserve atleast for one low-speed device
712  * transaction. According to USB Bandwidth Analysis white paper and also
713  * as per OHCI Specification 1.0a, section 7.3.5, page 123, one low-speed
714  * transaction takes 0x628h full speed bits (197 bytes), which comes to
715  * around 13% of USB frame time.
716  *
717  * The periodic transfers will  get around 87% of USB frame time.
718  */
719 #define	MAX_NON_PERIODIC_BANDWIDTH	197
720 #define	MAX_PERIODIC_BANDWIDTH		(MAX_USB_BUS_BANDWIDTH - SOF - \
721 					EOF - MAX_NON_PERIODIC_BANDWIDTH)
722 
723 /*
724  * The USB periodic transfers like interrupt and isochronous transfers
725  * after completion of SOF and USB non-periodic transfers.
726  */
727 #define	PERIODIC_XFER_STARTS		(MAX_USB_BUS_BANDWIDTH - \
728 					SOF - MAX_NON_PERIODIC_BANDWIDTH)
729 
730 /* Number of Bits Per Byte */
731 #define	BITS_PER_BYTE			8
732 
733 /*
734  * The following are the protocol overheads in terms of Bytes for the
735  * different transfer types.  All these protocol overhead  values are
736  * derived from the 5.9.3 section of USB Specification	and  with the
737  * help of Bandwidth Analysis white paper which is posted on the  USB
738  * developer forum.
739  */
740 #define	FS_NON_ISOC_PROTO_OVERHEAD	14
741 #define	FS_ISOC_INPUT_PROTO_OVERHEAD	11
742 #define	FS_ISOC_OUTPUT_PROTO_OVERHEAD	10
743 #define	LOW_SPEED_PROTO_OVERHEAD	97
744 #define	HUB_LOW_SPEED_PROTO_OVERHEAD	01
745 
746 /*
747  * The Host Controller (HC) delays are the USB host controller specific
748  * delays. The value shown below is the host  controller delay for  the
749  * RIO USB host controller.  This value was calculated and  given by the
750  * Sun USB hardware people.
751  */
752 #define	HOST_CONTROLLER_DELAY		18
753 
754 /*
755  * The low speed clock below represents that to transmit one low-speed
756  * bit takes eight times more than one full speed bit time.
757  */
758 #define	LOW_SPEED_CLOCK			8
759 
760 
761 /*
762  * Macros for setting/getting information
763  */
764 #define	Get_ED(addr)		ddi_get32(ohcip->ohci_ed_pool_mem_handle, \
765 					(uint32_t *)&addr)
766 
767 #define	Set_ED(addr, val)	ddi_put32(ohcip->ohci_ed_pool_mem_handle,  \
768 					((uint32_t *)&addr), \
769 					((int32_t)(val)))
770 
771 #define	Get_TD(addr)		ddi_get32(ohcip->ohci_td_pool_mem_handle, \
772 					(uint32_t *)&addr)
773 
774 #define	Set_TD(addr, val)	ddi_put32(ohcip->ohci_td_pool_mem_handle, \
775 					((uint32_t *)&addr), \
776 					((uint32_t)(uintptr_t)(val)))
777 
778 #define	Get_HCCA(addr)		ddi_get32(ohcip->ohci_hcca_mem_handle, \
779 					(uint32_t *)&addr)
780 
781 #define	Set_HCCA(addr, val)	ddi_put32(ohcip->ohci_hcca_mem_handle, \
782 					((uint32_t *)&addr), \
783 					((int32_t)(val)))
784 
785 #define	Get_OpReg(addr)		ddi_get32(ohcip->ohci_regs_handle, \
786 					(uint32_t *)&ohcip->ohci_regsp->addr)
787 
788 #define	Set_OpReg(addr, val)	ddi_put32(ohcip->ohci_regs_handle, \
789 				((uint32_t *)&ohcip->ohci_regsp->addr), \
790 					((int32_t)(val)))
791 
792 #define	Sync_HCCA(ohcip)	(void) ddi_dma_sync( \
793 				ohcip->ohci_hcca_dma_handle, \
794 				0, sizeof (ohci_hcca_t), \
795 				DDI_DMA_SYNC_FORCPU);
796 
797 #define	Sync_ED_TD_Pool(ohcip)	(void) ddi_dma_sync( \
798 				ohcip->ohci_ed_pool_dma_handle, \
799 				0, OHCI_ED_POOL_SIZE * sizeof (ohci_ed_t), \
800 				DDI_DMA_SYNC_FORCPU); \
801 				(void) ddi_dma_sync( \
802 				ohcip->ohci_td_pool_dma_handle, \
803 				0, OHCI_TD_POOL_SIZE * sizeof (ohci_td_t), \
804 				DDI_DMA_SYNC_FORCPU);
805 
806 #define	Sync_IO_Buffer(dma_handle, length) \
807 				(void) ddi_dma_sync(dma_handle, \
808 				0, length, DDI_DMA_SYNC_FORCPU);
809 #define	Sync_IO_Buffer_for_device(dma_handle, length) \
810 				(void) ddi_dma_sync(dma_handle, \
811 				0, length, DDI_DMA_SYNC_FORDEV);
812 
813 /*
814  * Macros to speed handling of 32bit IDs
815  */
816 #define	OHCI_GET_ID(x)		id32_alloc((void *)(x), KM_SLEEP)
817 #define	OHCI_LOOKUP_ID(x)	id32_lookup((x))
818 #define	OHCI_FREE_ID(x)		id32_free((x))
819 
820 
821 /*
822  * Miscellaneous definitions.
823  */
824 
825 /* Data toggle bits */
826 #define	DATA0		0
827 #define	DATA1		1
828 
829 /* sKip bit actions */
830 #define	CLEAR_sKip	0
831 #define	SET_sKip	1
832 
833 typedef uint_t		skip_bit_t;
834 
835 /*
836  * Setup Packet
837  */
838 typedef struct setup_pkt {
839 	uchar_t	bmRequestType;
840 	uchar_t	bRequest;
841 	ushort_t wValue;
842 	ushort_t wIndex;
843 	ushort_t wLength;
844 }setup_pkt_t;
845 
846 #define	SETUP_SIZE		8	/* Setup packet is always 8 bytes */
847 
848 #define	REQUEST_TYPE_OFFSET	0
849 #define	REQUEST_OFFSET		1
850 #define	VALUE_OFFSET		2
851 #define	INDEX_OFFSET		4
852 #define	LENGTH_OFFSET		6
853 
854 #define	TYPE_DEV_TO_HOST	0x80000000
855 #define	DEVICE			0x00000001
856 #define	CONFIGURATION		0x00000002
857 
858 /*
859  * The following are used in attach to	 indicate
860  * what has been succesfully allocated, so detach
861  * can remove them.
862  */
863 #define	OHCI_ATTACH		0x01	/* ohci driver initilization */
864 #define	OHCI_ZALLOC		0x02	/* Memory for ohci state structure */
865 #define	OHCI_INTR		0x04	/* Interrupt handler registered */
866 #define	OHCI_USBAREG		0x08	/* USBA registered */
867 #define	OHCI_RHREG		0x10	/* Root hub driver loaded */
868 
869 #define	OHCI_UNIT(dev)	(getminor((dev)) & ~HUBD_IS_ROOT_HUB)
870 
871 /*
872  * Debug printing
873  * Masks
874  */
875 #define	PRINT_MASK_ATTA		0x00000001	/* Attach time */
876 #define	PRINT_MASK_LISTS	0x00000002	/* List management */
877 #define	PRINT_MASK_ROOT_HUB	0x00000004	/* Root hub stuff */
878 #define	PRINT_MASK_ALLOC	0x00000008	/* Alloc/dealloc descr */
879 #define	PRINT_MASK_INTR		0x00000010	/* Interrupt handling */
880 #define	PRINT_MASK_BW		0x00000020	/* Bandwidth */
881 #define	PRINT_MASK_CBOPS	0x00000040	/* CB-OPS */
882 #define	PRINT_MASK_HCDI		0x00000080	/* HCDI entry points */
883 #define	PRINT_MASK_DUMPING	0x00000100	/* Dump ohci info */
884 #define	PRINT_MASK_ALL		0xFFFFFFFF
885 
886 
887 /* Polling support */
888 int		ohci_hcdi_polled_input_init(
889 				usba_pipe_handle_data_t	*ph,
890 				uchar_t			**polled_buf,
891 				usb_console_info_impl_t	*info);
892 int		ohci_hcdi_polled_input_enter(
893 				usb_console_info_impl_t	*info);
894 int		ohci_hcdi_polled_read(
895 				usb_console_info_impl_t	*info,
896 				uint_t			*num_characters);
897 int		ohci_hcdi_polled_input_exit(
898 				usb_console_info_impl_t	*info);
899 int		ohci_hcdi_polled_input_fini(
900 				usb_console_info_impl_t	*info);
901 
902 int		ohci_hcdi_polled_output_init(
903 				usba_pipe_handle_data_t	*ph,
904 				usb_console_info_impl_t	*console_output_info);
905 int		ohci_hcdi_polled_output_enter(
906 				usb_console_info_impl_t	*info);
907 int		ohci_hcdi_polled_write(
908 				usb_console_info_impl_t *info,
909 				uchar_t *buf,
910 				uint_t num_characters,
911 				uint_t *num_characters_written);
912 int		ohci_hcdi_polled_output_exit(
913 				usb_console_info_impl_t	*info);
914 int		ohci_hcdi_polled_output_fini(
915 				usb_console_info_impl_t *info);
916 
917 /* Root hub related functions */
918 int		ohci_init_root_hub(
919 				ohci_state_t		*ohcip);
920 int		ohci_load_root_hub_driver(
921 				ohci_state_t		*ohcip);
922 int		ohci_unload_root_hub_driver(
923 				ohci_state_t		*ohcip);
924 int		ohci_handle_root_hub_pipe_open(
925 				usba_pipe_handle_data_t	*ph,
926 				usb_flags_t		flags);
927 int		ohci_handle_root_hub_pipe_close(
928 				usba_pipe_handle_data_t	*ph);
929 int		ohci_handle_root_hub_pipe_reset(
930 				usba_pipe_handle_data_t	*ph,
931 				usb_flags_t		flags);
932 int		ohci_handle_root_hub_request(
933 				ohci_state_t		*ohcip,
934 				usba_pipe_handle_data_t	*ph,
935 				usb_ctrl_req_t		*ctrl_reqp);
936 int		ohci_handle_root_hub_pipe_start_intr_polling(
937 				usba_pipe_handle_data_t	*ph,
938 				usb_intr_req_t		*intr_reqp,
939 				usb_flags_t		flags);
940 void		ohci_handle_root_hub_pipe_stop_intr_polling(
941 				usba_pipe_handle_data_t	*ph,
942 				usb_flags_t		flags);
943 void		ohci_handle_root_hub_status_change(void *arg);
944 
945 /* Endpoint Descriptor (ED) related functions */
946 ohci_ed_t	*ohci_alloc_hc_ed(
947 				ohci_state_t		*ohcip,
948 				usba_pipe_handle_data_t	*ph);
949 void		ohci_deallocate_ed(
950 				ohci_state_t		*ohcip,
951 				ohci_ed_t		*old_ed);
952 uint32_t	ohci_ed_cpu_to_iommu(
953 				ohci_state_t		*ohcip,
954 				ohci_ed_t		*addr);
955 
956 /* Transfer Descriptor (TD) related functions */
957 int		ohci_start_periodic_pipe_polling(
958 				ohci_state_t		*ohcip,
959 				usba_pipe_handle_data_t	*ph,
960 				usb_opaque_t		periodic_in_reqp,
961 				usb_flags_t		flags);
962 void		ohci_traverse_tds(
963 				ohci_state_t		*ohcip,
964 				usba_pipe_handle_data_t	*ph);
965 void		ohci_deallocate_td(
966 				ohci_state_t		*ohcip,
967 				ohci_td_t		*old_td);
968 uint32_t	ohci_td_cpu_to_iommu(
969 				ohci_state_t		*ohcip,
970 				ohci_td_t		*addr);
971 ohci_td_t	*ohci_td_iommu_to_cpu(
972 				ohci_state_t		*ohcip,
973 				uintptr_t		addr);
974 size_t		ohci_get_td_residue(
975 				ohci_state_t		*ohcip,
976 				ohci_td_t		*td);
977 void		ohci_init_td(
978 				ohci_state_t		*ohcip,
979 				ohci_trans_wrapper_t	*tw,
980 				uint32_t		hctd_dma_offs,
981 				size_t			hctd_length,
982 				ohci_td_t		*td);
983 
984 /* Transfer Wrapper (TW) functions */
985 void		ohci_deallocate_tw_resources(
986 				ohci_state_t		*ohcip,
987 				ohci_pipe_private_t	*pp,
988 				ohci_trans_wrapper_t	*tw);
989 
990 /* Interrupt Handling functions */
991 void		ohci_handle_frame_number_overflow(
992 				ohci_state_t		*ohcip);
993 
994 /* Miscillaneous functions */
995 ohci_state_t	*ohci_obtain_state(
996 				dev_info_t		*dip);
997 int		ohci_state_is_operational(
998 				ohci_state_t		*ohcip);
999 int		ohci_do_soft_reset(
1000 				ohci_state_t		*ohcip);
1001 usb_frame_number_t ohci_get_current_frame_number(
1002 				ohci_state_t		*ohcip);
1003 void		ohci_handle_outstanding_requests(
1004 				ohci_state_t		*ohcip,
1005 				ohci_pipe_private_t	*pp);
1006 int	ohci_allocate_tds_for_tw(
1007 				ohci_state_t		*ohcip,
1008 				ohci_trans_wrapper_t	*tw,
1009 				size_t			td_count);
1010 
1011 #ifdef __cplusplus
1012 }
1013 #endif
1014 
1015 #endif /* _SYS_USB_OHCID_H */
1016