1 /******************************************************************************
2
3 Copyright (c) 2001-2011, Intel Corporation
4 All rights reserved.
5
6 Redistribution and use in source and binary forms, with or without
7 modification, are permitted provided that the following conditions are met:
8
9 1. Redistributions of source code must retain the above copyright notice,
10 this list of conditions and the following disclaimer.
11
12 2. Redistributions in binary form must reproduce the above copyright
13 notice, this list of conditions and the following disclaimer in the
14 documentation and/or other materials provided with the distribution.
15
16 3. Neither the name of the Intel Corporation nor the names of its
17 contributors may be used to endorse or promote products derived from
18 this software without specific prior written permission.
19
20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
30 POSSIBILITY OF SUCH DAMAGE.
31
32 ******************************************************************************/
33 /*$FreeBSD$*/
34
35 /*
36 * 82540EM Gigabit Ethernet Controller
37 * 82540EP Gigabit Ethernet Controller
38 * 82545EM Gigabit Ethernet Controller (Copper)
39 * 82545EM Gigabit Ethernet Controller (Fiber)
40 * 82545GM Gigabit Ethernet Controller
41 * 82546EB Gigabit Ethernet Controller (Copper)
42 * 82546EB Gigabit Ethernet Controller (Fiber)
43 * 82546GB Gigabit Ethernet Controller
44 */
45
46 #include "e1000_api.h"
47
48 static s32 e1000_init_phy_params_82540(struct e1000_hw *hw);
49 static s32 e1000_init_nvm_params_82540(struct e1000_hw *hw);
50 static s32 e1000_init_mac_params_82540(struct e1000_hw *hw);
51 static s32 e1000_adjust_serdes_amplitude_82540(struct e1000_hw *hw);
52 static void e1000_clear_hw_cntrs_82540(struct e1000_hw *hw);
53 static s32 e1000_init_hw_82540(struct e1000_hw *hw);
54 static s32 e1000_reset_hw_82540(struct e1000_hw *hw);
55 static s32 e1000_set_phy_mode_82540(struct e1000_hw *hw);
56 static s32 e1000_set_vco_speed_82540(struct e1000_hw *hw);
57 static s32 e1000_setup_copper_link_82540(struct e1000_hw *hw);
58 static s32 e1000_setup_fiber_serdes_link_82540(struct e1000_hw *hw);
59 static void e1000_power_down_phy_copper_82540(struct e1000_hw *hw);
60 static s32 e1000_read_mac_addr_82540(struct e1000_hw *hw);
61
62 /**
63 * e1000_init_phy_params_82540 - Init PHY func ptrs.
64 * @hw: pointer to the HW structure
65 **/
e1000_init_phy_params_82540(struct e1000_hw * hw)66 static s32 e1000_init_phy_params_82540(struct e1000_hw *hw)
67 {
68 struct e1000_phy_info *phy = &hw->phy;
69 s32 ret_val = E1000_SUCCESS;
70
71 phy->addr = 1;
72 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
73 phy->reset_delay_us = 10000;
74 phy->type = e1000_phy_m88;
75
76 /* Function Pointers */
77 phy->ops.check_polarity = e1000_check_polarity_m88;
78 phy->ops.commit = e1000_phy_sw_reset_generic;
79 phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88;
80 phy->ops.get_cable_length = e1000_get_cable_length_m88;
81 phy->ops.get_cfg_done = e1000_get_cfg_done_generic;
82 phy->ops.read_reg = e1000_read_phy_reg_m88;
83 phy->ops.reset = e1000_phy_hw_reset_generic;
84 phy->ops.write_reg = e1000_write_phy_reg_m88;
85 phy->ops.get_info = e1000_get_phy_info_m88;
86 phy->ops.power_up = e1000_power_up_phy_copper;
87 phy->ops.power_down = e1000_power_down_phy_copper_82540;
88
89 ret_val = e1000_get_phy_id(hw);
90 if (ret_val)
91 goto out;
92
93 /* Verify phy id */
94 switch (hw->mac.type) {
95 case e1000_82540:
96 case e1000_82545:
97 case e1000_82545_rev_3:
98 case e1000_82546:
99 case e1000_82546_rev_3:
100 if (phy->id == M88E1011_I_PHY_ID)
101 break;
102 /* Fall Through */
103 default:
104 ret_val = -E1000_ERR_PHY;
105 goto out;
106 break;
107 }
108
109 out:
110 return ret_val;
111 }
112
113 /**
114 * e1000_init_nvm_params_82540 - Init NVM func ptrs.
115 * @hw: pointer to the HW structure
116 **/
e1000_init_nvm_params_82540(struct e1000_hw * hw)117 static s32 e1000_init_nvm_params_82540(struct e1000_hw *hw)
118 {
119 struct e1000_nvm_info *nvm = &hw->nvm;
120 u32 eecd = E1000_READ_REG(hw, E1000_EECD);
121
122 DEBUGFUNC("e1000_init_nvm_params_82540");
123
124 nvm->type = e1000_nvm_eeprom_microwire;
125 nvm->delay_usec = 50;
126 nvm->opcode_bits = 3;
127 switch (nvm->override) {
128 case e1000_nvm_override_microwire_large:
129 nvm->address_bits = 8;
130 nvm->word_size = 256;
131 break;
132 case e1000_nvm_override_microwire_small:
133 nvm->address_bits = 6;
134 nvm->word_size = 64;
135 break;
136 default:
137 nvm->address_bits = eecd & E1000_EECD_SIZE ? 8 : 6;
138 nvm->word_size = eecd & E1000_EECD_SIZE ? 256 : 64;
139 break;
140 }
141
142 /* Function Pointers */
143 nvm->ops.acquire = e1000_acquire_nvm_generic;
144 nvm->ops.read = e1000_read_nvm_microwire;
145 nvm->ops.release = e1000_release_nvm_generic;
146 nvm->ops.update = e1000_update_nvm_checksum_generic;
147 nvm->ops.valid_led_default = e1000_valid_led_default_generic;
148 nvm->ops.validate = e1000_validate_nvm_checksum_generic;
149 nvm->ops.write = e1000_write_nvm_microwire;
150
151 return E1000_SUCCESS;
152 }
153
154 /**
155 * e1000_init_mac_params_82540 - Init MAC func ptrs.
156 * @hw: pointer to the HW structure
157 **/
e1000_init_mac_params_82540(struct e1000_hw * hw)158 static s32 e1000_init_mac_params_82540(struct e1000_hw *hw)
159 {
160 struct e1000_mac_info *mac = &hw->mac;
161 s32 ret_val = E1000_SUCCESS;
162
163 DEBUGFUNC("e1000_init_mac_params_82540");
164
165 /* Set media type */
166 switch (hw->device_id) {
167 case E1000_DEV_ID_82545EM_FIBER:
168 case E1000_DEV_ID_82545GM_FIBER:
169 case E1000_DEV_ID_82546EB_FIBER:
170 case E1000_DEV_ID_82546GB_FIBER:
171 hw->phy.media_type = e1000_media_type_fiber;
172 break;
173 case E1000_DEV_ID_82545GM_SERDES:
174 case E1000_DEV_ID_82546GB_SERDES:
175 hw->phy.media_type = e1000_media_type_internal_serdes;
176 break;
177 default:
178 hw->phy.media_type = e1000_media_type_copper;
179 break;
180 }
181
182 /* Set mta register count */
183 mac->mta_reg_count = 128;
184 /* Set rar entry count */
185 mac->rar_entry_count = E1000_RAR_ENTRIES;
186
187 /* Function pointers */
188
189 /* bus type/speed/width */
190 mac->ops.get_bus_info = e1000_get_bus_info_pci_generic;
191 /* function id */
192 mac->ops.set_lan_id = e1000_set_lan_id_multi_port_pci;
193 /* reset */
194 mac->ops.reset_hw = e1000_reset_hw_82540;
195 /* hw initialization */
196 mac->ops.init_hw = e1000_init_hw_82540;
197 /* link setup */
198 mac->ops.setup_link = e1000_setup_link_generic;
199 /* physical interface setup */
200 mac->ops.setup_physical_interface =
201 (hw->phy.media_type == e1000_media_type_copper)
202 ? e1000_setup_copper_link_82540
203 : e1000_setup_fiber_serdes_link_82540;
204 /* check for link */
205 switch (hw->phy.media_type) {
206 case e1000_media_type_copper:
207 mac->ops.check_for_link = e1000_check_for_copper_link_generic;
208 break;
209 case e1000_media_type_fiber:
210 mac->ops.check_for_link = e1000_check_for_fiber_link_generic;
211 break;
212 case e1000_media_type_internal_serdes:
213 mac->ops.check_for_link = e1000_check_for_serdes_link_generic;
214 break;
215 default:
216 ret_val = -E1000_ERR_CONFIG;
217 goto out;
218 break;
219 }
220 /* link info */
221 mac->ops.get_link_up_info =
222 (hw->phy.media_type == e1000_media_type_copper)
223 ? e1000_get_speed_and_duplex_copper_generic
224 : e1000_get_speed_and_duplex_fiber_serdes_generic;
225 /* multicast address update */
226 mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic;
227 /* writing VFTA */
228 mac->ops.write_vfta = e1000_write_vfta_generic;
229 /* clearing VFTA */
230 mac->ops.clear_vfta = e1000_clear_vfta_generic;
231 /* read mac address */
232 mac->ops.read_mac_addr = e1000_read_mac_addr_82540;
233 /* ID LED init */
234 mac->ops.id_led_init = e1000_id_led_init_generic;
235 /* setup LED */
236 mac->ops.setup_led = e1000_setup_led_generic;
237 /* cleanup LED */
238 mac->ops.cleanup_led = e1000_cleanup_led_generic;
239 /* turn on/off LED */
240 mac->ops.led_on = e1000_led_on_generic;
241 mac->ops.led_off = e1000_led_off_generic;
242 /* clear hardware counters */
243 mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82540;
244
245 out:
246 return ret_val;
247 }
248
249 /**
250 * e1000_init_function_pointers_82540 - Init func ptrs.
251 * @hw: pointer to the HW structure
252 *
253 * Called to initialize all function pointers and parameters.
254 **/
e1000_init_function_pointers_82540(struct e1000_hw * hw)255 void e1000_init_function_pointers_82540(struct e1000_hw *hw)
256 {
257 DEBUGFUNC("e1000_init_function_pointers_82540");
258
259 hw->mac.ops.init_params = e1000_init_mac_params_82540;
260 hw->nvm.ops.init_params = e1000_init_nvm_params_82540;
261 hw->phy.ops.init_params = e1000_init_phy_params_82540;
262 }
263
264 /**
265 * e1000_reset_hw_82540 - Reset hardware
266 * @hw: pointer to the HW structure
267 *
268 * This resets the hardware into a known state.
269 **/
e1000_reset_hw_82540(struct e1000_hw * hw)270 static s32 e1000_reset_hw_82540(struct e1000_hw *hw)
271 {
272 u32 ctrl, manc;
273 s32 ret_val = E1000_SUCCESS;
274
275 DEBUGFUNC("e1000_reset_hw_82540");
276
277 DEBUGOUT("Masking off all interrupts\n");
278 E1000_WRITE_REG(hw, E1000_IMC, 0xFFFFFFFF);
279
280 E1000_WRITE_REG(hw, E1000_RCTL, 0);
281 E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP);
282 E1000_WRITE_FLUSH(hw);
283
284 /*
285 * Delay to allow any outstanding PCI transactions to complete
286 * before resetting the device.
287 */
288 msec_delay(10);
289
290 ctrl = E1000_READ_REG(hw, E1000_CTRL);
291
292 DEBUGOUT("Issuing a global reset to 82540/82545/82546 MAC\n");
293 switch (hw->mac.type) {
294 case e1000_82545_rev_3:
295 case e1000_82546_rev_3:
296 E1000_WRITE_REG(hw, E1000_CTRL_DUP, ctrl | E1000_CTRL_RST);
297 break;
298 default:
299 /*
300 * These controllers can't ack the 64-bit write when
301 * issuing the reset, so we use IO-mapping as a
302 * workaround to issue the reset.
303 */
304 E1000_WRITE_REG_IO(hw, E1000_CTRL, ctrl | E1000_CTRL_RST);
305 break;
306 }
307
308 /* Wait for EEPROM reload */
309 msec_delay(5);
310
311 /* Disable HW ARPs on ASF enabled adapters */
312 manc = E1000_READ_REG(hw, E1000_MANC);
313 manc &= ~E1000_MANC_ARP_EN;
314 E1000_WRITE_REG(hw, E1000_MANC, manc);
315
316 E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff);
317 E1000_READ_REG(hw, E1000_ICR);
318
319 return ret_val;
320 }
321
322 /**
323 * e1000_init_hw_82540 - Initialize hardware
324 * @hw: pointer to the HW structure
325 *
326 * This inits the hardware readying it for operation.
327 **/
e1000_init_hw_82540(struct e1000_hw * hw)328 static s32 e1000_init_hw_82540(struct e1000_hw *hw)
329 {
330 struct e1000_mac_info *mac = &hw->mac;
331 u32 txdctl, ctrl_ext;
332 s32 ret_val = E1000_SUCCESS;
333 u16 i;
334
335 DEBUGFUNC("e1000_init_hw_82540");
336
337 /* Initialize identification LED */
338 ret_val = mac->ops.id_led_init(hw);
339 if (ret_val) {
340 DEBUGOUT("Error initializing identification LED\n");
341 /* This is not fatal and we should not stop init due to this */
342 }
343
344 /* Disabling VLAN filtering */
345 DEBUGOUT("Initializing the IEEE VLAN\n");
346 if (mac->type < e1000_82545_rev_3)
347 E1000_WRITE_REG(hw, E1000_VET, 0);
348
349 mac->ops.clear_vfta(hw);
350
351 /* Setup the receive address. */
352 e1000_init_rx_addrs_generic(hw, mac->rar_entry_count);
353
354 /* Zero out the Multicast HASH table */
355 DEBUGOUT("Zeroing the MTA\n");
356 for (i = 0; i < mac->mta_reg_count; i++) {
357 E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
358 /*
359 * Avoid back to back register writes by adding the register
360 * read (flush). This is to protect against some strange
361 * bridge configurations that may issue Memory Write Block
362 * (MWB) to our register space. The *_rev_3 hardware at
363 * least doesn't respond correctly to every other dword in an
364 * MWB to our register space.
365 */
366 E1000_WRITE_FLUSH(hw);
367 }
368
369 if (mac->type < e1000_82545_rev_3)
370 e1000_pcix_mmrbc_workaround_generic(hw);
371
372 /* Setup link and flow control */
373 ret_val = mac->ops.setup_link(hw);
374
375 txdctl = E1000_READ_REG(hw, E1000_TXDCTL(0));
376 txdctl = (txdctl & ~E1000_TXDCTL_WTHRESH) |
377 E1000_TXDCTL_FULL_TX_DESC_WB;
378 E1000_WRITE_REG(hw, E1000_TXDCTL(0), txdctl);
379
380 /*
381 * Clear all of the statistics registers (clear on read). It is
382 * important that we do this after we have tried to establish link
383 * because the symbol error count will increment wildly if there
384 * is no link.
385 */
386 e1000_clear_hw_cntrs_82540(hw);
387
388 if ((hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER) ||
389 (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3)) {
390 ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT);
391 /*
392 * Relaxed ordering must be disabled to avoid a parity
393 * error crash in a PCI slot.
394 */
395 ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
396 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext);
397 }
398
399 return ret_val;
400 }
401
402 /**
403 * e1000_setup_copper_link_82540 - Configure copper link settings
404 * @hw: pointer to the HW structure
405 *
406 * Calls the appropriate function to configure the link for auto-neg or forced
407 * speed and duplex. Then we check for link, once link is established calls
408 * to configure collision distance and flow control are called. If link is
409 * not established, we return -E1000_ERR_PHY (-2).
410 **/
e1000_setup_copper_link_82540(struct e1000_hw * hw)411 static s32 e1000_setup_copper_link_82540(struct e1000_hw *hw)
412 {
413 u32 ctrl;
414 s32 ret_val = E1000_SUCCESS;
415 u16 data;
416
417 DEBUGFUNC("e1000_setup_copper_link_82540");
418
419 ctrl = E1000_READ_REG(hw, E1000_CTRL);
420 ctrl |= E1000_CTRL_SLU;
421 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
422 E1000_WRITE_REG(hw, E1000_CTRL, ctrl);
423
424 ret_val = e1000_set_phy_mode_82540(hw);
425 if (ret_val)
426 goto out;
427
428 if (hw->mac.type == e1000_82545_rev_3 ||
429 hw->mac.type == e1000_82546_rev_3) {
430 ret_val = hw->phy.ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL,
431 &data);
432 if (ret_val)
433 goto out;
434 data |= 0x00000008;
435 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_SPEC_CTRL,
436 data);
437 if (ret_val)
438 goto out;
439 }
440
441 ret_val = e1000_copper_link_setup_m88(hw);
442 if (ret_val)
443 goto out;
444
445 ret_val = e1000_setup_copper_link_generic(hw);
446
447 out:
448 return ret_val;
449 }
450
451 /**
452 * e1000_setup_fiber_serdes_link_82540 - Setup link for fiber/serdes
453 * @hw: pointer to the HW structure
454 *
455 * Set the output amplitude to the value in the EEPROM and adjust the VCO
456 * speed to improve Bit Error Rate (BER) performance. Configures collision
457 * distance and flow control for fiber and serdes links. Upon successful
458 * setup, poll for link.
459 **/
e1000_setup_fiber_serdes_link_82540(struct e1000_hw * hw)460 static s32 e1000_setup_fiber_serdes_link_82540(struct e1000_hw *hw)
461 {
462 struct e1000_mac_info *mac = &hw->mac;
463 s32 ret_val = E1000_SUCCESS;
464
465 DEBUGFUNC("e1000_setup_fiber_serdes_link_82540");
466
467 switch (mac->type) {
468 case e1000_82545_rev_3:
469 case e1000_82546_rev_3:
470 if (hw->phy.media_type == e1000_media_type_internal_serdes) {
471 /*
472 * If we're on serdes media, adjust the output
473 * amplitude to value set in the EEPROM.
474 */
475 ret_val = e1000_adjust_serdes_amplitude_82540(hw);
476 if (ret_val)
477 goto out;
478 }
479 /* Adjust VCO speed to improve BER performance */
480 ret_val = e1000_set_vco_speed_82540(hw);
481 if (ret_val)
482 goto out;
483 default:
484 break;
485 }
486
487 ret_val = e1000_setup_fiber_serdes_link_generic(hw);
488
489 out:
490 return ret_val;
491 }
492
493 /**
494 * e1000_adjust_serdes_amplitude_82540 - Adjust amplitude based on EEPROM
495 * @hw: pointer to the HW structure
496 *
497 * Adjust the SERDES output amplitude based on the EEPROM settings.
498 **/
e1000_adjust_serdes_amplitude_82540(struct e1000_hw * hw)499 static s32 e1000_adjust_serdes_amplitude_82540(struct e1000_hw *hw)
500 {
501 s32 ret_val = E1000_SUCCESS;
502 u16 nvm_data;
503
504 DEBUGFUNC("e1000_adjust_serdes_amplitude_82540");
505
506 ret_val = hw->nvm.ops.read(hw, NVM_SERDES_AMPLITUDE, 1, &nvm_data);
507 if (ret_val)
508 goto out;
509
510 if (nvm_data != NVM_RESERVED_WORD) {
511 /* Adjust serdes output amplitude only. */
512 nvm_data &= NVM_SERDES_AMPLITUDE_MASK;
513 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_EXT_CTRL,
514 nvm_data);
515 if (ret_val)
516 goto out;
517 }
518
519 out:
520 return ret_val;
521 }
522
523 /**
524 * e1000_set_vco_speed_82540 - Set VCO speed for better performance
525 * @hw: pointer to the HW structure
526 *
527 * Set the VCO speed to improve Bit Error Rate (BER) performance.
528 **/
e1000_set_vco_speed_82540(struct e1000_hw * hw)529 static s32 e1000_set_vco_speed_82540(struct e1000_hw *hw)
530 {
531 s32 ret_val = E1000_SUCCESS;
532 u16 default_page = 0;
533 u16 phy_data;
534
535 DEBUGFUNC("e1000_set_vco_speed_82540");
536
537 /* Set PHY register 30, page 5, bit 8 to 0 */
538
539 ret_val = hw->phy.ops.read_reg(hw, M88E1000_PHY_PAGE_SELECT,
540 &default_page);
541 if (ret_val)
542 goto out;
543
544 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005);
545 if (ret_val)
546 goto out;
547
548 ret_val = hw->phy.ops.read_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
549 if (ret_val)
550 goto out;
551
552 phy_data &= ~M88E1000_PHY_VCO_REG_BIT8;
553 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
554 if (ret_val)
555 goto out;
556
557 /* Set PHY register 30, page 4, bit 11 to 1 */
558
559 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004);
560 if (ret_val)
561 goto out;
562
563 ret_val = hw->phy.ops.read_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
564 if (ret_val)
565 goto out;
566
567 phy_data |= M88E1000_PHY_VCO_REG_BIT11;
568 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
569 if (ret_val)
570 goto out;
571
572 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT,
573 default_page);
574
575 out:
576 return ret_val;
577 }
578
579 /**
580 * e1000_set_phy_mode_82540 - Set PHY to class A mode
581 * @hw: pointer to the HW structure
582 *
583 * Sets the PHY to class A mode and assumes the following operations will
584 * follow to enable the new class mode:
585 * 1. Do a PHY soft reset.
586 * 2. Restart auto-negotiation or force link.
587 **/
e1000_set_phy_mode_82540(struct e1000_hw * hw)588 static s32 e1000_set_phy_mode_82540(struct e1000_hw *hw)
589 {
590 s32 ret_val = E1000_SUCCESS;
591 u16 nvm_data;
592
593 DEBUGFUNC("e1000_set_phy_mode_82540");
594
595 if (hw->mac.type != e1000_82545_rev_3)
596 goto out;
597
598 ret_val = hw->nvm.ops.read(hw, NVM_PHY_CLASS_WORD, 1, &nvm_data);
599 if (ret_val) {
600 ret_val = -E1000_ERR_PHY;
601 goto out;
602 }
603
604 if ((nvm_data != NVM_RESERVED_WORD) && (nvm_data & NVM_PHY_CLASS_A)) {
605 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT,
606 0x000B);
607 if (ret_val) {
608 ret_val = -E1000_ERR_PHY;
609 goto out;
610 }
611 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL,
612 0x8104);
613 if (ret_val) {
614 ret_val = -E1000_ERR_PHY;
615 goto out;
616 }
617
618 }
619
620 out:
621 return ret_val;
622 }
623
624 /**
625 * e1000_power_down_phy_copper_82540 - Remove link in case of PHY power down
626 * @hw: pointer to the HW structure
627 *
628 * In the case of a PHY power down to save power, or to turn off link during a
629 * driver unload, or wake on lan is not enabled, remove the link.
630 **/
e1000_power_down_phy_copper_82540(struct e1000_hw * hw)631 static void e1000_power_down_phy_copper_82540(struct e1000_hw *hw)
632 {
633 /* If the management interface is not enabled, then power down */
634 if (!(E1000_READ_REG(hw, E1000_MANC) & E1000_MANC_SMBUS_EN))
635 e1000_power_down_phy_copper(hw);
636
637 return;
638 }
639
640 /**
641 * e1000_clear_hw_cntrs_82540 - Clear device specific hardware counters
642 * @hw: pointer to the HW structure
643 *
644 * Clears the hardware counters by reading the counter registers.
645 **/
e1000_clear_hw_cntrs_82540(struct e1000_hw * hw)646 static void e1000_clear_hw_cntrs_82540(struct e1000_hw *hw)
647 {
648 DEBUGFUNC("e1000_clear_hw_cntrs_82540");
649
650 e1000_clear_hw_cntrs_base_generic(hw);
651
652 E1000_READ_REG(hw, E1000_PRC64);
653 E1000_READ_REG(hw, E1000_PRC127);
654 E1000_READ_REG(hw, E1000_PRC255);
655 E1000_READ_REG(hw, E1000_PRC511);
656 E1000_READ_REG(hw, E1000_PRC1023);
657 E1000_READ_REG(hw, E1000_PRC1522);
658 E1000_READ_REG(hw, E1000_PTC64);
659 E1000_READ_REG(hw, E1000_PTC127);
660 E1000_READ_REG(hw, E1000_PTC255);
661 E1000_READ_REG(hw, E1000_PTC511);
662 E1000_READ_REG(hw, E1000_PTC1023);
663 E1000_READ_REG(hw, E1000_PTC1522);
664
665 E1000_READ_REG(hw, E1000_ALGNERRC);
666 E1000_READ_REG(hw, E1000_RXERRC);
667 E1000_READ_REG(hw, E1000_TNCRS);
668 E1000_READ_REG(hw, E1000_CEXTERR);
669 E1000_READ_REG(hw, E1000_TSCTC);
670 E1000_READ_REG(hw, E1000_TSCTFC);
671
672 E1000_READ_REG(hw, E1000_MGTPRC);
673 E1000_READ_REG(hw, E1000_MGTPDC);
674 E1000_READ_REG(hw, E1000_MGTPTC);
675 }
676
677 /**
678 * e1000_read_mac_addr_82540 - Read device MAC address
679 * @hw: pointer to the HW structure
680 *
681 * Reads the device MAC address from the EEPROM and stores the value.
682 * Since devices with two ports use the same EEPROM, we increment the
683 * last bit in the MAC address for the second port.
684 *
685 * This version is being used over generic because of customer issues
686 * with VmWare and Virtual Box when using generic. It seems in
687 * the emulated 82545, RAR[0] does NOT have a valid address after a
688 * reset, this older method works and using this breaks nothing for
689 * these legacy adapters.
690 **/
e1000_read_mac_addr_82540(struct e1000_hw * hw)691 s32 e1000_read_mac_addr_82540(struct e1000_hw *hw)
692 {
693 s32 ret_val = E1000_SUCCESS;
694 u16 offset, nvm_data, i;
695
696 DEBUGFUNC("e1000_read_mac_addr");
697
698 for (i = 0; i < ETH_ADDR_LEN; i += 2) {
699 offset = i >> 1;
700 ret_val = hw->nvm.ops.read(hw, offset, 1, &nvm_data);
701 if (ret_val) {
702 DEBUGOUT("NVM Read Error\n");
703 goto out;
704 }
705 hw->mac.perm_addr[i] = (u8)(nvm_data & 0xFF);
706 hw->mac.perm_addr[i+1] = (u8)(nvm_data >> 8);
707 }
708
709 /* Flip last bit of mac address if we're on second port */
710 if (hw->bus.func == E1000_FUNC_1)
711 hw->mac.perm_addr[5] ^= 1;
712
713 for (i = 0; i < ETH_ADDR_LEN; i++)
714 hw->mac.addr[i] = hw->mac.perm_addr[i];
715
716 out:
717 return ret_val;
718 }
719