1 /*-
2 * SPDX-License-Identifier: ISC
3 *
4 * Copyright (c) 2002-2009 Sam Leffler, Errno Consulting
5 * Copyright (c) 2002-2008 Atheros Communications, Inc.
6 *
7 * Permission to use, copy, modify, and/or distribute this software for any
8 * purpose with or without fee is hereby granted, provided that the above
9 * copyright notice and this permission notice appear in all copies.
10 *
11 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
12 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
13 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
14 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
15 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
16 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
17 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
18 */
19 #include "opt_ah.h"
20
21 #include "ah.h"
22 #include "ah_internal.h"
23
24 #include "ah_eeprom_v14.h"
25
26 #include "ar5416/ar5416.h"
27 #include "ar5416/ar5416reg.h"
28 #include "ar5416/ar5416phy.h"
29
30 #define N(a) (sizeof(a)/sizeof(a[0]))
31
32 struct ar2133State {
33 RF_HAL_FUNCS base; /* public state, must be first */
34 uint16_t pcdacTable[1];
35
36 uint32_t *Bank0Data;
37 uint32_t *Bank1Data;
38 uint32_t *Bank2Data;
39 uint32_t *Bank3Data;
40 uint32_t *Bank6Data;
41 uint32_t *Bank7Data;
42
43 /* NB: Bank*Data storage follows */
44 };
45 #define AR2133(ah) ((struct ar2133State *) AH5212(ah)->ah_rfHal)
46
47 #define ar5416ModifyRfBuffer ar5212ModifyRfBuffer /*XXX*/
48
49 void ar5416ModifyRfBuffer(uint32_t *rfBuf, uint32_t reg32,
50 uint32_t numBits, uint32_t firstBit, uint32_t column);
51
52 static void
ar2133WriteRegs(struct ath_hal * ah,u_int modesIndex,u_int freqIndex,int writes)53 ar2133WriteRegs(struct ath_hal *ah, u_int modesIndex, u_int freqIndex,
54 int writes)
55 {
56 (void) ath_hal_ini_write(ah, &AH5416(ah)->ah_ini_bb_rfgain,
57 freqIndex, writes);
58 }
59
60 /*
61 * Fix on 2.4 GHz band for orientation sensitivity issue by increasing
62 * rf_pwd_icsyndiv.
63 *
64 * Theoretical Rules:
65 * if 2 GHz band
66 * if forceBiasAuto
67 * if synth_freq < 2412
68 * bias = 0
69 * else if 2412 <= synth_freq <= 2422
70 * bias = 1
71 * else // synth_freq > 2422
72 * bias = 2
73 * else if forceBias > 0
74 * bias = forceBias & 7
75 * else
76 * no change, use value from ini file
77 * else
78 * no change, invalid band
79 *
80 * 1st Mod:
81 * 2422 also uses value of 2
82 * <approved>
83 *
84 * 2nd Mod:
85 * Less than 2412 uses value of 0, 2412 and above uses value of 2
86 */
87 static void
ar2133ForceBias(struct ath_hal * ah,uint16_t synth_freq)88 ar2133ForceBias(struct ath_hal *ah, uint16_t synth_freq)
89 {
90 uint32_t tmp_reg;
91 int reg_writes = 0;
92 uint32_t new_bias = 0;
93 struct ar2133State *priv = AR2133(ah);
94
95 /* XXX this is a bit of a silly check for 2.4ghz channels -adrian */
96 if (synth_freq >= 3000)
97 return;
98
99 if (synth_freq < 2412)
100 new_bias = 0;
101 else if (synth_freq < 2422)
102 new_bias = 1;
103 else
104 new_bias = 2;
105
106 /* pre-reverse this field */
107 tmp_reg = ath_hal_reverseBits(new_bias, 3);
108
109 HALDEBUG(ah, HAL_DEBUG_ANY, "%s: Force rf_pwd_icsyndiv to %1d on %4d\n",
110 __func__, new_bias, synth_freq);
111
112 /* swizzle rf_pwd_icsyndiv */
113 ar5416ModifyRfBuffer(priv->Bank6Data, tmp_reg, 3, 181, 3);
114
115 /* write Bank 6 with new params */
116 ath_hal_ini_bank_write(ah, &AH5416(ah)->ah_ini_bank6, priv->Bank6Data, reg_writes);
117 }
118
119 /*
120 * Take the MHz channel value and set the Channel value
121 *
122 * ASSUMES: Writes enabled to analog bus
123 */
124 static HAL_BOOL
ar2133SetChannel(struct ath_hal * ah,const struct ieee80211_channel * chan)125 ar2133SetChannel(struct ath_hal *ah, const struct ieee80211_channel *chan)
126 {
127 uint32_t channelSel = 0;
128 uint32_t bModeSynth = 0;
129 uint32_t aModeRefSel = 0;
130 uint32_t reg32 = 0;
131 uint16_t freq;
132 CHAN_CENTERS centers;
133
134 OS_MARK(ah, AH_MARK_SETCHANNEL, chan->ic_freq);
135
136 ar5416GetChannelCenters(ah, chan, ¢ers);
137 freq = centers.synth_center;
138
139 if (freq < 4800) {
140 uint32_t txctl;
141
142 if (((freq - 2192) % 5) == 0) {
143 channelSel = ((freq - 672) * 2 - 3040)/10;
144 bModeSynth = 0;
145 } else if (((freq - 2224) % 5) == 0) {
146 channelSel = ((freq - 704) * 2 - 3040) / 10;
147 bModeSynth = 1;
148 } else {
149 HALDEBUG(ah, HAL_DEBUG_ANY,
150 "%s: invalid channel %u MHz\n", __func__, freq);
151 return AH_FALSE;
152 }
153
154 channelSel = (channelSel << 2) & 0xff;
155 channelSel = ath_hal_reverseBits(channelSel, 8);
156
157 txctl = OS_REG_READ(ah, AR_PHY_CCK_TX_CTRL);
158 if (freq == 2484) {
159 /* Enable channel spreading for channel 14 */
160 OS_REG_WRITE(ah, AR_PHY_CCK_TX_CTRL,
161 txctl | AR_PHY_CCK_TX_CTRL_JAPAN);
162 } else {
163 OS_REG_WRITE(ah, AR_PHY_CCK_TX_CTRL,
164 txctl &~ AR_PHY_CCK_TX_CTRL_JAPAN);
165 }
166 /*
167 * Handle programming the RF synth for odd frequencies in the
168 * 4.9->5GHz range. This matches the programming from the
169 * later model 802.11abg RF synths.
170 *
171 * This interoperates on the quarter rate channels with the
172 * AR5112 and later RF synths. Please note that the synthesiser
173 * isn't able to completely accurately represent these frequencies
174 * (as the resolution in this reference is 2.5MHz) and thus it will
175 * be slightly "off centre." This matches the same slightly
176 * incorrect * centre frequency behaviour that the AR5112 and later
177 * channel selection code has.
178 *
179 * This is disabled because it hasn't been tested for regulatory
180 * compliance and neither have the NICs which would use it.
181 * So if you enable this code, you must first ensure that you've
182 * re-certified the NICs in question beforehand or you will be
183 * violating your local regulatory rules and breaking the law.
184 */
185 #if 0
186 } else if (((freq % 5) == 2) && (freq <= 5435)) {
187 freq = freq - 2;
188 channelSel = ath_hal_reverseBits(
189 (uint32_t) (((freq - 4800) * 10) / 25 + 1), 8);
190 /* XXX what about for Howl/Sowl? */
191 aModeRefSel = ath_hal_reverseBits(0, 2);
192 #endif
193 } else if ((freq % 20) == 0 && freq >= 5120) {
194 channelSel = ath_hal_reverseBits(((freq - 4800) / 20 << 2), 8);
195 if (AR_SREV_HOWL(ah) || AR_SREV_SOWL_10_OR_LATER(ah))
196 aModeRefSel = ath_hal_reverseBits(3, 2);
197 else
198 aModeRefSel = ath_hal_reverseBits(1, 2);
199 } else if ((freq % 10) == 0) {
200 channelSel = ath_hal_reverseBits(((freq - 4800) / 10 << 1), 8);
201 if (AR_SREV_HOWL(ah) || AR_SREV_SOWL_10_OR_LATER(ah))
202 aModeRefSel = ath_hal_reverseBits(2, 2);
203 else
204 aModeRefSel = ath_hal_reverseBits(1, 2);
205 } else if ((freq % 5) == 0) {
206 channelSel = ath_hal_reverseBits((freq - 4800) / 5, 8);
207 aModeRefSel = ath_hal_reverseBits(1, 2);
208 } else {
209 HALDEBUG(ah, HAL_DEBUG_UNMASKABLE,
210 "%s: invalid channel %u MHz\n",
211 __func__, freq);
212 return AH_FALSE;
213 }
214
215 /* Workaround for hw bug - AR5416 specific */
216 if (AR_SREV_OWL(ah) && ah->ah_config.ah_ar5416_biasadj)
217 ar2133ForceBias(ah, freq);
218
219 reg32 = (channelSel << 8) | (aModeRefSel << 2) | (bModeSynth << 1) |
220 (1 << 5) | 0x1;
221
222 OS_REG_WRITE(ah, AR_PHY(0x37), reg32);
223
224 AH_PRIVATE(ah)->ah_curchan = chan;
225 return AH_TRUE;
226
227 }
228
229 /*
230 * Return a reference to the requested RF Bank.
231 */
232 static uint32_t *
ar2133GetRfBank(struct ath_hal * ah,int bank)233 ar2133GetRfBank(struct ath_hal *ah, int bank)
234 {
235 struct ar2133State *priv = AR2133(ah);
236
237 HALASSERT(priv != AH_NULL);
238 switch (bank) {
239 case 1: return priv->Bank1Data;
240 case 2: return priv->Bank2Data;
241 case 3: return priv->Bank3Data;
242 case 6: return priv->Bank6Data;
243 case 7: return priv->Bank7Data;
244 }
245 HALDEBUG(ah, HAL_DEBUG_ANY, "%s: unknown RF Bank %d requested\n",
246 __func__, bank);
247 return AH_NULL;
248 }
249
250 /*
251 * Reads EEPROM header info from device structure and programs
252 * all rf registers
253 *
254 * REQUIRES: Access to the analog rf device
255 */
256 static HAL_BOOL
ar2133SetRfRegs(struct ath_hal * ah,const struct ieee80211_channel * chan,uint16_t modesIndex,uint16_t * rfXpdGain)257 ar2133SetRfRegs(struct ath_hal *ah, const struct ieee80211_channel *chan,
258 uint16_t modesIndex, uint16_t *rfXpdGain)
259 {
260 struct ar2133State *priv = AR2133(ah);
261 int writes;
262
263 HALASSERT(priv);
264
265 /* Setup Bank 0 Write */
266 ath_hal_ini_bank_setup(priv->Bank0Data, &AH5416(ah)->ah_ini_bank0, 1);
267
268 /* Setup Bank 1 Write */
269 ath_hal_ini_bank_setup(priv->Bank1Data, &AH5416(ah)->ah_ini_bank1, 1);
270
271 /* Setup Bank 2 Write */
272 ath_hal_ini_bank_setup(priv->Bank2Data, &AH5416(ah)->ah_ini_bank2, 1);
273
274 /* Setup Bank 3 Write */
275 ath_hal_ini_bank_setup(priv->Bank3Data, &AH5416(ah)->ah_ini_bank3, modesIndex);
276
277 /* Setup Bank 6 Write */
278 ath_hal_ini_bank_setup(priv->Bank6Data, &AH5416(ah)->ah_ini_bank6, modesIndex);
279
280 /* Only the 5 or 2 GHz OB/DB need to be set for a mode */
281 if (IEEE80211_IS_CHAN_2GHZ(chan)) {
282 HALDEBUG(ah, HAL_DEBUG_EEPROM, "%s: 2ghz: OB_2:%d, DB_2:%d\n",
283 __func__,
284 ath_hal_eepromGet(ah, AR_EEP_OB_2, AH_NULL),
285 ath_hal_eepromGet(ah, AR_EEP_DB_2, AH_NULL));
286 ar5416ModifyRfBuffer(priv->Bank6Data,
287 ath_hal_eepromGet(ah, AR_EEP_OB_2, AH_NULL), 3, 197, 0);
288 ar5416ModifyRfBuffer(priv->Bank6Data,
289 ath_hal_eepromGet(ah, AR_EEP_DB_2, AH_NULL), 3, 194, 0);
290 } else {
291 HALDEBUG(ah, HAL_DEBUG_EEPROM, "%s: 5ghz: OB_5:%d, DB_5:%d\n",
292 __func__,
293 ath_hal_eepromGet(ah, AR_EEP_OB_5, AH_NULL),
294 ath_hal_eepromGet(ah, AR_EEP_DB_5, AH_NULL));
295 ar5416ModifyRfBuffer(priv->Bank6Data,
296 ath_hal_eepromGet(ah, AR_EEP_OB_5, AH_NULL), 3, 203, 0);
297 ar5416ModifyRfBuffer(priv->Bank6Data,
298 ath_hal_eepromGet(ah, AR_EEP_DB_5, AH_NULL), 3, 200, 0);
299 }
300 /* Setup Bank 7 Setup */
301 ath_hal_ini_bank_setup(priv->Bank7Data, &AH5416(ah)->ah_ini_bank7, 1);
302
303 /* Write Analog registers */
304 writes = ath_hal_ini_bank_write(ah, &AH5416(ah)->ah_ini_bank0,
305 priv->Bank0Data, 0);
306 writes = ath_hal_ini_bank_write(ah, &AH5416(ah)->ah_ini_bank1,
307 priv->Bank1Data, writes);
308 writes = ath_hal_ini_bank_write(ah, &AH5416(ah)->ah_ini_bank2,
309 priv->Bank2Data, writes);
310 writes = ath_hal_ini_bank_write(ah, &AH5416(ah)->ah_ini_bank3,
311 priv->Bank3Data, writes);
312 writes = ath_hal_ini_bank_write(ah, &AH5416(ah)->ah_ini_bank6,
313 priv->Bank6Data, writes);
314 (void) ath_hal_ini_bank_write(ah, &AH5416(ah)->ah_ini_bank7,
315 priv->Bank7Data, writes);
316
317 return AH_TRUE;
318 #undef RF_BANK_SETUP
319 }
320
321 /*
322 * Read the transmit power levels from the structures taken from EEPROM
323 * Interpolate read transmit power values for this channel
324 * Organize the transmit power values into a table for writing into the hardware
325 */
326
327 static HAL_BOOL
ar2133SetPowerTable(struct ath_hal * ah,int16_t * pPowerMin,int16_t * pPowerMax,const struct ieee80211_channel * chan,uint16_t * rfXpdGain)328 ar2133SetPowerTable(struct ath_hal *ah, int16_t *pPowerMin, int16_t *pPowerMax,
329 const struct ieee80211_channel *chan, uint16_t *rfXpdGain)
330 {
331 return AH_TRUE;
332 }
333
334 #if 0
335 static int16_t
336 ar2133GetMinPower(struct ath_hal *ah, EXPN_DATA_PER_CHANNEL_5112 *data)
337 {
338 int i, minIndex;
339 int16_t minGain,minPwr,minPcdac,retVal;
340
341 /* Assume NUM_POINTS_XPD0 > 0 */
342 minGain = data->pDataPerXPD[0].xpd_gain;
343 for (minIndex=0,i=1; i<NUM_XPD_PER_CHANNEL; i++) {
344 if (data->pDataPerXPD[i].xpd_gain < minGain) {
345 minIndex = i;
346 minGain = data->pDataPerXPD[i].xpd_gain;
347 }
348 }
349 minPwr = data->pDataPerXPD[minIndex].pwr_t4[0];
350 minPcdac = data->pDataPerXPD[minIndex].pcdac[0];
351 for (i=1; i<NUM_POINTS_XPD0; i++) {
352 if (data->pDataPerXPD[minIndex].pwr_t4[i] < minPwr) {
353 minPwr = data->pDataPerXPD[minIndex].pwr_t4[i];
354 minPcdac = data->pDataPerXPD[minIndex].pcdac[i];
355 }
356 }
357 retVal = minPwr - (minPcdac*2);
358 return(retVal);
359 }
360 #endif
361
362 static HAL_BOOL
ar2133GetChannelMaxMinPower(struct ath_hal * ah,const struct ieee80211_channel * chan,int16_t * maxPow,int16_t * minPow)363 ar2133GetChannelMaxMinPower(struct ath_hal *ah,
364 const struct ieee80211_channel *chan,
365 int16_t *maxPow, int16_t *minPow)
366 {
367 #if 0
368 struct ath_hal_5212 *ahp = AH5212(ah);
369 int numChannels=0,i,last;
370 int totalD, totalF,totalMin;
371 EXPN_DATA_PER_CHANNEL_5112 *data=AH_NULL;
372 EEPROM_POWER_EXPN_5112 *powerArray=AH_NULL;
373
374 *maxPow = 0;
375 if (IS_CHAN_A(chan)) {
376 powerArray = ahp->ah_modePowerArray5112;
377 data = powerArray[headerInfo11A].pDataPerChannel;
378 numChannels = powerArray[headerInfo11A].numChannels;
379 } else if (IS_CHAN_G(chan) || IS_CHAN_108G(chan)) {
380 /* XXX - is this correct? Should we also use the same power for turbo G? */
381 powerArray = ahp->ah_modePowerArray5112;
382 data = powerArray[headerInfo11G].pDataPerChannel;
383 numChannels = powerArray[headerInfo11G].numChannels;
384 } else if (IS_CHAN_B(chan)) {
385 powerArray = ahp->ah_modePowerArray5112;
386 data = powerArray[headerInfo11B].pDataPerChannel;
387 numChannels = powerArray[headerInfo11B].numChannels;
388 } else {
389 return (AH_TRUE);
390 }
391 /* Make sure the channel is in the range of the TP values
392 * (freq piers)
393 */
394 if ((numChannels < 1) ||
395 (chan->channel < data[0].channelValue) ||
396 (chan->channel > data[numChannels-1].channelValue))
397 return(AH_FALSE);
398
399 /* Linearly interpolate the power value now */
400 for (last=0,i=0;
401 (i<numChannels) && (chan->channel > data[i].channelValue);
402 last=i++);
403 totalD = data[i].channelValue - data[last].channelValue;
404 if (totalD > 0) {
405 totalF = data[i].maxPower_t4 - data[last].maxPower_t4;
406 *maxPow = (int8_t) ((totalF*(chan->channel-data[last].channelValue) + data[last].maxPower_t4*totalD)/totalD);
407
408 totalMin = ar2133GetMinPower(ah,&data[i]) - ar2133GetMinPower(ah, &data[last]);
409 *minPow = (int8_t) ((totalMin*(chan->channel-data[last].channelValue) + ar2133GetMinPower(ah, &data[last])*totalD)/totalD);
410 return (AH_TRUE);
411 } else {
412 if (chan->channel == data[i].channelValue) {
413 *maxPow = data[i].maxPower_t4;
414 *minPow = ar2133GetMinPower(ah, &data[i]);
415 return(AH_TRUE);
416 } else
417 return(AH_FALSE);
418 }
419 #else
420 // XXX TODO: actually go implement for 11n chips!
421 *maxPow = *minPow = 0;
422 return AH_FALSE;
423 #endif
424 }
425
426 /*
427 * The ordering of nfarray is thus:
428 *
429 * nfarray[0]: Chain 0 ctl
430 * nfarray[1]: Chain 1 ctl
431 * nfarray[2]: Chain 2 ctl
432 * nfarray[3]: Chain 0 ext
433 * nfarray[4]: Chain 1 ext
434 * nfarray[5]: Chain 2 ext
435 */
436 static void
ar2133GetNoiseFloor(struct ath_hal * ah,int16_t nfarray[])437 ar2133GetNoiseFloor(struct ath_hal *ah, int16_t nfarray[])
438 {
439 struct ath_hal_5416 *ahp = AH5416(ah);
440 int16_t nf;
441
442 /*
443 * Blank nf array - some chips may only
444 * have one or two RX chainmasks enabled.
445 */
446 nfarray[0] = nfarray[1] = nfarray[2] = 0;
447 nfarray[3] = nfarray[4] = nfarray[5] = 0;
448
449 switch (ahp->ah_rx_chainmask) {
450 case 0x7:
451 nf = MS(OS_REG_READ(ah, AR_PHY_CH2_CCA), AR_PHY_CH2_MINCCA_PWR);
452 if (nf & 0x100)
453 nf = 0 - ((nf ^ 0x1ff) + 1);
454 HALDEBUG(ah, HAL_DEBUG_NFCAL,
455 "NF calibrated [ctl] [chain 2] is %d\n", nf);
456 nfarray[2] = nf;
457
458 nf = MS(OS_REG_READ(ah, AR_PHY_CH2_EXT_CCA), AR_PHY_CH2_EXT_MINCCA_PWR);
459 if (nf & 0x100)
460 nf = 0 - ((nf ^ 0x1ff) + 1);
461 HALDEBUG(ah, HAL_DEBUG_NFCAL,
462 "NF calibrated [ext] [chain 2] is %d\n", nf);
463 nfarray[5] = nf;
464 /* fall thru... */
465 case 0x3:
466 case 0x5:
467 nf = MS(OS_REG_READ(ah, AR_PHY_CH1_CCA), AR_PHY_CH1_MINCCA_PWR);
468 if (nf & 0x100)
469 nf = 0 - ((nf ^ 0x1ff) + 1);
470 HALDEBUG(ah, HAL_DEBUG_NFCAL,
471 "NF calibrated [ctl] [chain 1] is %d\n", nf);
472 nfarray[1] = nf;
473
474 nf = MS(OS_REG_READ(ah, AR_PHY_CH1_EXT_CCA), AR_PHY_CH1_EXT_MINCCA_PWR);
475 if (nf & 0x100)
476 nf = 0 - ((nf ^ 0x1ff) + 1);
477 HALDEBUG(ah, HAL_DEBUG_NFCAL,
478 "NF calibrated [ext] [chain 1] is %d\n", nf);
479 nfarray[4] = nf;
480 /* fall thru... */
481 case 0x1:
482 nf = MS(OS_REG_READ(ah, AR_PHY_CCA), AR_PHY_MINCCA_PWR);
483 if (nf & 0x100)
484 nf = 0 - ((nf ^ 0x1ff) + 1);
485 HALDEBUG(ah, HAL_DEBUG_NFCAL,
486 "NF calibrated [ctl] [chain 0] is %d\n", nf);
487 nfarray[0] = nf;
488
489 nf = MS(OS_REG_READ(ah, AR_PHY_EXT_CCA), AR_PHY_EXT_MINCCA_PWR);
490 if (nf & 0x100)
491 nf = 0 - ((nf ^ 0x1ff) + 1);
492 HALDEBUG(ah, HAL_DEBUG_NFCAL,
493 "NF calibrated [ext] [chain 0] is %d\n", nf);
494 nfarray[3] = nf;
495
496 break;
497 }
498 }
499
500 /*
501 * Adjust NF based on statistical values for 5GHz frequencies.
502 * Stubbed:Not used by Fowl
503 */
504 static int16_t
ar2133GetNfAdjust(struct ath_hal * ah,const HAL_CHANNEL_INTERNAL * c)505 ar2133GetNfAdjust(struct ath_hal *ah, const HAL_CHANNEL_INTERNAL *c)
506 {
507 return 0;
508 }
509
510 /*
511 * Free memory for analog bank scratch buffers
512 */
513 static void
ar2133RfDetach(struct ath_hal * ah)514 ar2133RfDetach(struct ath_hal *ah)
515 {
516 struct ath_hal_5212 *ahp = AH5212(ah);
517
518 HALASSERT(ahp->ah_rfHal != AH_NULL);
519 ath_hal_free(ahp->ah_rfHal);
520 ahp->ah_rfHal = AH_NULL;
521 }
522
523 /*
524 * Allocate memory for analog bank scratch buffers
525 * Scratch Buffer will be reinitialized every reset so no need to zero now
526 */
527 HAL_BOOL
ar2133RfAttach(struct ath_hal * ah,HAL_STATUS * status)528 ar2133RfAttach(struct ath_hal *ah, HAL_STATUS *status)
529 {
530 struct ath_hal_5212 *ahp = AH5212(ah);
531 struct ar2133State *priv;
532 uint32_t *bankData;
533
534 HALDEBUG(ah, HAL_DEBUG_ATTACH, "%s: attach AR2133 radio\n", __func__);
535
536 HALASSERT(ahp->ah_rfHal == AH_NULL);
537 priv = ath_hal_malloc(sizeof(struct ar2133State)
538 + AH5416(ah)->ah_ini_bank0.rows * sizeof(uint32_t)
539 + AH5416(ah)->ah_ini_bank1.rows * sizeof(uint32_t)
540 + AH5416(ah)->ah_ini_bank2.rows * sizeof(uint32_t)
541 + AH5416(ah)->ah_ini_bank3.rows * sizeof(uint32_t)
542 + AH5416(ah)->ah_ini_bank6.rows * sizeof(uint32_t)
543 + AH5416(ah)->ah_ini_bank7.rows * sizeof(uint32_t)
544 );
545 if (priv == AH_NULL) {
546 HALDEBUG(ah, HAL_DEBUG_ANY,
547 "%s: cannot allocate private state\n", __func__);
548 *status = HAL_ENOMEM; /* XXX */
549 return AH_FALSE;
550 }
551 priv->base.rfDetach = ar2133RfDetach;
552 priv->base.writeRegs = ar2133WriteRegs;
553 priv->base.getRfBank = ar2133GetRfBank;
554 priv->base.setChannel = ar2133SetChannel;
555 priv->base.setRfRegs = ar2133SetRfRegs;
556 priv->base.setPowerTable = ar2133SetPowerTable;
557 priv->base.getChannelMaxMinPower = ar2133GetChannelMaxMinPower;
558 priv->base.getNfAdjust = ar2133GetNfAdjust;
559
560 bankData = (uint32_t *) &priv[1];
561 priv->Bank0Data = bankData, bankData += AH5416(ah)->ah_ini_bank0.rows;
562 priv->Bank1Data = bankData, bankData += AH5416(ah)->ah_ini_bank1.rows;
563 priv->Bank2Data = bankData, bankData += AH5416(ah)->ah_ini_bank2.rows;
564 priv->Bank3Data = bankData, bankData += AH5416(ah)->ah_ini_bank3.rows;
565 priv->Bank6Data = bankData, bankData += AH5416(ah)->ah_ini_bank6.rows;
566 priv->Bank7Data = bankData, bankData += AH5416(ah)->ah_ini_bank7.rows;
567
568 ahp->ah_pcdacTable = priv->pcdacTable;
569 ahp->ah_pcdacTableSize = sizeof(priv->pcdacTable);
570 ahp->ah_rfHal = &priv->base;
571 /*
572 * Set noise floor adjust method; we arrange a
573 * direct call instead of thunking.
574 */
575 AH_PRIVATE(ah)->ah_getNfAdjust = priv->base.getNfAdjust;
576 AH_PRIVATE(ah)->ah_getNoiseFloor = ar2133GetNoiseFloor;
577
578 return AH_TRUE;
579 }
580
581 static HAL_BOOL
ar2133Probe(struct ath_hal * ah)582 ar2133Probe(struct ath_hal *ah)
583 {
584 return (AR_SREV_OWL(ah) || AR_SREV_HOWL(ah) || AR_SREV_SOWL(ah));
585 }
586
587 AH_RF(RF2133, ar2133Probe, ar2133RfAttach);
588