1 /*-
2 * Copyright (c) 2015 Oleksandr Tymoshenko <gonzo@freebsd.org>
3 * Copyright (c) 2011 Ben Gray <ben.r.gray@gmail.com>.
4 * All rights reserved.
5 *
6 * Redistribution and use in source and binary forms, with or without
7 * modification, are permitted provided that the following conditions
8 * are met:
9 * 1. Redistributions of source code must retain the above copyright
10 * notice, this list of conditions and the following disclaimer.
11 * 2. Redistributions in binary form must reproduce the above copyright
12 * notice, this list of conditions and the following disclaimer in the
13 * documentation and/or other materials provided with the distribution.
14 *
15 * THIS SOFTWARE IS PROVIDED BY AUTHOR AND CONTRIBUTORS ``AS IS'' AND
16 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
17 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
18 * ARE DISCLAIMED. IN NO EVENT SHALL AUTHOR OR CONTRIBUTORS BE LIABLE
19 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
20 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
21 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
22 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
23 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
24 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
25 * SUCH DAMAGE.
26 */
27
28 #include <sys/param.h>
29 #include <sys/systm.h>
30 #include <sys/conf.h>
31 #include <sys/kernel.h>
32 #include <sys/rman.h>
33 #include <sys/module.h>
34
35 #include <dev/fdt/simplebus.h>
36 #include <dev/ofw/ofw_bus_subr.h>
37
38 #include <machine/bus.h>
39
40 #include <arm/ti/ti_sysc.h>
41 #include <arm/ti/usb/omap_usb.h>
42
43 /*
44 * USB Host Module
45 */
46
47 /* UHH */
48 #define OMAP_USBHOST_UHH_REVISION 0x0000
49 #define OMAP_USBHOST_UHH_SYSCONFIG 0x0010
50 #define OMAP_USBHOST_UHH_SYSSTATUS 0x0014
51 #define OMAP_USBHOST_UHH_HOSTCONFIG 0x0040
52 #define OMAP_USBHOST_UHH_DEBUG_CSR 0x0044
53
54 /* UHH Register Set */
55 #define UHH_SYSCONFIG_MIDLEMODE_MASK (3UL << 12)
56 #define UHH_SYSCONFIG_MIDLEMODE_SMARTSTANDBY (2UL << 12)
57 #define UHH_SYSCONFIG_MIDLEMODE_NOSTANDBY (1UL << 12)
58 #define UHH_SYSCONFIG_MIDLEMODE_FORCESTANDBY (0UL << 12)
59 #define UHH_SYSCONFIG_CLOCKACTIVITY (1UL << 8)
60 #define UHH_SYSCONFIG_SIDLEMODE_MASK (3UL << 3)
61 #define UHH_SYSCONFIG_SIDLEMODE_SMARTIDLE (2UL << 3)
62 #define UHH_SYSCONFIG_SIDLEMODE_NOIDLE (1UL << 3)
63 #define UHH_SYSCONFIG_SIDLEMODE_FORCEIDLE (0UL << 3)
64 #define UHH_SYSCONFIG_ENAWAKEUP (1UL << 2)
65 #define UHH_SYSCONFIG_SOFTRESET (1UL << 1)
66 #define UHH_SYSCONFIG_AUTOIDLE (1UL << 0)
67
68 #define UHH_HOSTCONFIG_APP_START_CLK (1UL << 31)
69 #define UHH_HOSTCONFIG_P3_CONNECT_STATUS (1UL << 10)
70 #define UHH_HOSTCONFIG_P2_CONNECT_STATUS (1UL << 9)
71 #define UHH_HOSTCONFIG_P1_CONNECT_STATUS (1UL << 8)
72 #define UHH_HOSTCONFIG_ENA_INCR_ALIGN (1UL << 5)
73 #define UHH_HOSTCONFIG_ENA_INCR16 (1UL << 4)
74 #define UHH_HOSTCONFIG_ENA_INCR8 (1UL << 3)
75 #define UHH_HOSTCONFIG_ENA_INCR4 (1UL << 2)
76 #define UHH_HOSTCONFIG_AUTOPPD_ON_OVERCUR_EN (1UL << 1)
77 #define UHH_HOSTCONFIG_P1_ULPI_BYPASS (1UL << 0)
78
79 /* The following are on rev2 (OMAP44xx) of the EHCI only */
80 #define UHH_SYSCONFIG_IDLEMODE_MASK (3UL << 2)
81 #define UHH_SYSCONFIG_IDLEMODE_NOIDLE (1UL << 2)
82 #define UHH_SYSCONFIG_STANDBYMODE_MASK (3UL << 4)
83 #define UHH_SYSCONFIG_STANDBYMODE_NOSTDBY (1UL << 4)
84
85 #define UHH_HOSTCONFIG_P1_MODE_MASK (3UL << 16)
86 #define UHH_HOSTCONFIG_P1_MODE_ULPI_PHY (0UL << 16)
87 #define UHH_HOSTCONFIG_P1_MODE_UTMI_PHY (1UL << 16)
88 #define UHH_HOSTCONFIG_P1_MODE_HSIC (3UL << 16)
89 #define UHH_HOSTCONFIG_P2_MODE_MASK (3UL << 18)
90 #define UHH_HOSTCONFIG_P2_MODE_ULPI_PHY (0UL << 18)
91 #define UHH_HOSTCONFIG_P2_MODE_UTMI_PHY (1UL << 18)
92 #define UHH_HOSTCONFIG_P2_MODE_HSIC (3UL << 18)
93
94 /*
95 * Values of UHH_REVISION - Note: these are not given in the TRM but taken
96 * from the linux OMAP EHCI driver (thanks guys). It has been verified on
97 * a Panda and Beagle board.
98 */
99 #define OMAP_UHH_REV1 0x00000010 /* OMAP3 */
100 #define OMAP_UHH_REV2 0x50700100 /* OMAP4 */
101
102 struct omap_uhh_softc {
103 struct simplebus_softc simplebus_sc;
104 device_t sc_dev;
105
106 /* UHH register set */
107 struct resource* uhh_mem_res;
108
109 /* The revision of the HS USB HOST read from UHH_REVISION */
110 uint32_t uhh_rev;
111
112 /* The following details are provided by conf hints */
113 int port_mode[3];
114 };
115
116 static device_attach_t omap_uhh_attach;
117 static device_detach_t omap_uhh_detach;
118
119 static inline uint32_t
omap_uhh_read_4(struct omap_uhh_softc * sc,bus_size_t off)120 omap_uhh_read_4(struct omap_uhh_softc *sc, bus_size_t off)
121 {
122 return bus_read_4(sc->uhh_mem_res, off);
123 }
124
125 static inline void
omap_uhh_write_4(struct omap_uhh_softc * sc,bus_size_t off,uint32_t val)126 omap_uhh_write_4(struct omap_uhh_softc *sc, bus_size_t off, uint32_t val)
127 {
128 bus_write_4(sc->uhh_mem_res, off, val);
129 }
130
131 static int
omap_uhh_init(struct omap_uhh_softc * isc)132 omap_uhh_init(struct omap_uhh_softc *isc)
133 {
134 uint8_t tll_ch_mask;
135 uint32_t reg;
136 int i;
137
138 /* Enable Clocks for high speed USBHOST */
139 ti_sysc_clock_enable(device_get_parent(isc->sc_dev));
140
141 /* Read the UHH revision */
142 isc->uhh_rev = omap_uhh_read_4(isc, OMAP_USBHOST_UHH_REVISION);
143 device_printf(isc->sc_dev, "UHH revision 0x%08x\n", isc->uhh_rev);
144
145 /* FIXME */
146 #if 0
147 if (isc->uhh_rev == OMAP_UHH_REV2) {
148 /* For OMAP44xx devices you have to enable the per-port clocks:
149 * PHY_MODE - External ULPI clock
150 * TTL_MODE - Internal UTMI clock
151 * HSIC_MODE - Internal 480Mhz and 60Mhz clocks
152 */
153 switch(isc->port_mode[0]) {
154 case EHCI_HCD_OMAP_MODE_UNKNOWN:
155 break;
156 case EHCI_HCD_OMAP_MODE_PHY:
157 if (ti_prcm_clk_set_source(USBP1_PHY_CLK, EXT_CLK))
158 device_printf(isc->sc_dev,
159 "failed to set clock source for port 0\n");
160 if (ti_prcm_clk_enable(USBP1_PHY_CLK))
161 device_printf(isc->sc_dev,
162 "failed to set clock USBP1_PHY_CLK source for port 0\n");
163 break;
164 case EHCI_HCD_OMAP_MODE_TLL:
165 if (ti_prcm_clk_enable(USBP1_UTMI_CLK))
166 device_printf(isc->sc_dev,
167 "failed to set clock USBP1_PHY_CLK source for port 0\n");
168 break;
169 case EHCI_HCD_OMAP_MODE_HSIC:
170 if (ti_prcm_clk_enable(USBP1_HSIC_CLK))
171 device_printf(isc->sc_dev,
172 "failed to set clock USBP1_PHY_CLK source for port 0\n");
173 break;
174 default:
175 device_printf(isc->sc_dev, "unknown port mode %d for port 0\n", isc->port_mode[0]);
176 }
177 switch(isc->port_mode[1]) {
178 case EHCI_HCD_OMAP_MODE_UNKNOWN:
179 break;
180 case EHCI_HCD_OMAP_MODE_PHY:
181 if (ti_prcm_clk_set_source(USBP2_PHY_CLK, EXT_CLK))
182 device_printf(isc->sc_dev,
183 "failed to set clock source for port 0\n");
184 if (ti_prcm_clk_enable(USBP2_PHY_CLK))
185 device_printf(isc->sc_dev,
186 "failed to set clock USBP2_PHY_CLK source for port 1\n");
187 break;
188 case EHCI_HCD_OMAP_MODE_TLL:
189 if (ti_prcm_clk_enable(USBP2_UTMI_CLK))
190 device_printf(isc->sc_dev,
191 "failed to set clock USBP2_UTMI_CLK source for port 1\n");
192 break;
193 case EHCI_HCD_OMAP_MODE_HSIC:
194 if (ti_prcm_clk_enable(USBP2_HSIC_CLK))
195 device_printf(isc->sc_dev,
196 "failed to set clock USBP2_HSIC_CLK source for port 1\n");
197 break;
198 default:
199 device_printf(isc->sc_dev, "unknown port mode %d for port 1\n", isc->port_mode[1]);
200 }
201 }
202 #endif
203
204 /* Put UHH in SmartIdle/SmartStandby mode */
205 reg = omap_uhh_read_4(isc, OMAP_USBHOST_UHH_SYSCONFIG);
206 if (isc->uhh_rev == OMAP_UHH_REV1) {
207 reg &= ~(UHH_SYSCONFIG_SIDLEMODE_MASK |
208 UHH_SYSCONFIG_MIDLEMODE_MASK);
209 reg |= (UHH_SYSCONFIG_ENAWAKEUP |
210 UHH_SYSCONFIG_AUTOIDLE |
211 UHH_SYSCONFIG_CLOCKACTIVITY |
212 UHH_SYSCONFIG_SIDLEMODE_SMARTIDLE |
213 UHH_SYSCONFIG_MIDLEMODE_SMARTSTANDBY);
214 } else if (isc->uhh_rev == OMAP_UHH_REV2) {
215 reg &= ~UHH_SYSCONFIG_IDLEMODE_MASK;
216 reg |= UHH_SYSCONFIG_IDLEMODE_NOIDLE;
217 reg &= ~UHH_SYSCONFIG_STANDBYMODE_MASK;
218 reg |= UHH_SYSCONFIG_STANDBYMODE_NOSTDBY;
219 }
220 omap_uhh_write_4(isc, OMAP_USBHOST_UHH_SYSCONFIG, reg);
221 device_printf(isc->sc_dev, "OMAP_UHH_SYSCONFIG: 0x%08x\n", reg);
222
223 reg = omap_uhh_read_4(isc, OMAP_USBHOST_UHH_HOSTCONFIG);
224
225 /* Setup ULPI bypass and burst configurations */
226 reg |= (UHH_HOSTCONFIG_ENA_INCR4 |
227 UHH_HOSTCONFIG_ENA_INCR8 |
228 UHH_HOSTCONFIG_ENA_INCR16);
229 reg &= ~UHH_HOSTCONFIG_ENA_INCR_ALIGN;
230
231 if (isc->uhh_rev == OMAP_UHH_REV1) {
232 if (isc->port_mode[0] == EHCI_HCD_OMAP_MODE_UNKNOWN)
233 reg &= ~UHH_HOSTCONFIG_P1_CONNECT_STATUS;
234 if (isc->port_mode[1] == EHCI_HCD_OMAP_MODE_UNKNOWN)
235 reg &= ~UHH_HOSTCONFIG_P2_CONNECT_STATUS;
236 if (isc->port_mode[2] == EHCI_HCD_OMAP_MODE_UNKNOWN)
237 reg &= ~UHH_HOSTCONFIG_P3_CONNECT_STATUS;
238
239 /* Bypass the TLL module for PHY mode operation */
240 if ((isc->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY) ||
241 (isc->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY) ||
242 (isc->port_mode[2] == EHCI_HCD_OMAP_MODE_PHY))
243 reg &= ~UHH_HOSTCONFIG_P1_ULPI_BYPASS;
244 else
245 reg |= UHH_HOSTCONFIG_P1_ULPI_BYPASS;
246
247 } else if (isc->uhh_rev == OMAP_UHH_REV2) {
248 reg |= UHH_HOSTCONFIG_APP_START_CLK;
249
250 /* Clear port mode fields for PHY mode*/
251 reg &= ~UHH_HOSTCONFIG_P1_MODE_MASK;
252 reg &= ~UHH_HOSTCONFIG_P2_MODE_MASK;
253
254 if (isc->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL)
255 reg |= UHH_HOSTCONFIG_P1_MODE_UTMI_PHY;
256 else if (isc->port_mode[0] == EHCI_HCD_OMAP_MODE_HSIC)
257 reg |= UHH_HOSTCONFIG_P1_MODE_HSIC;
258
259 if (isc->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL)
260 reg |= UHH_HOSTCONFIG_P2_MODE_UTMI_PHY;
261 else if (isc->port_mode[1] == EHCI_HCD_OMAP_MODE_HSIC)
262 reg |= UHH_HOSTCONFIG_P2_MODE_HSIC;
263 }
264
265 omap_uhh_write_4(isc, OMAP_USBHOST_UHH_HOSTCONFIG, reg);
266 device_printf(isc->sc_dev, "UHH setup done, uhh_hostconfig=0x%08x\n", reg);
267
268 /* I found the code and comments in the Linux EHCI driver - thanks guys :)
269 *
270 * "An undocumented "feature" in the OMAP3 EHCI controller, causes suspended
271 * ports to be taken out of suspend when the USBCMD.Run/Stop bit is cleared
272 * (for example when we do omap_uhh_bus_suspend). This breaks suspend-resume if
273 * the root-hub is allowed to suspend. Writing 1 to this undocumented
274 * register bit disables this feature and restores normal behavior."
275 */
276 #if 0
277 omap_uhh_write_4(isc, OMAP_USBHOST_INSNREG04,
278 OMAP_USBHOST_INSNREG04_DISABLE_UNSUSPEND);
279 #endif
280 tll_ch_mask = 0;
281 for (i = 0; i < OMAP_HS_USB_PORTS; i++) {
282 if (isc->port_mode[i] == EHCI_HCD_OMAP_MODE_TLL)
283 tll_ch_mask |= (1 << i);
284 }
285 if (tll_ch_mask)
286 omap_tll_utmi_enable(tll_ch_mask);
287
288 return(0);
289 }
290
291 /**
292 * omap_uhh_fini - shutdown the EHCI controller
293 * @isc: omap ehci device context
294 *
295 *
296 *
297 * LOCKING:
298 * none
299 *
300 * RETURNS:
301 * 0 on success, a negative error code on failure.
302 */
303 static void
omap_uhh_fini(struct omap_uhh_softc * isc)304 omap_uhh_fini(struct omap_uhh_softc *isc)
305 {
306 unsigned long timeout;
307
308 device_printf(isc->sc_dev, "Stopping TI EHCI USB Controller\n");
309
310 /* Set the timeout */
311 if (hz < 10)
312 timeout = 1;
313 else
314 timeout = (100 * hz) / 1000;
315
316 /* Reset the UHH, OHCI and EHCI modules */
317 omap_uhh_write_4(isc, OMAP_USBHOST_UHH_SYSCONFIG, 0x0002);
318 while ((omap_uhh_read_4(isc, OMAP_USBHOST_UHH_SYSSTATUS) & 0x07) == 0x00) {
319 /* Sleep for a tick */
320 pause("USBRESET", 1);
321
322 if (timeout-- == 0) {
323 device_printf(isc->sc_dev, "operation timed out\n");
324 break;
325 }
326 }
327
328 /* Disable functional and interface clocks for the TLL and HOST modules */
329 ti_sysc_clock_disable(device_get_parent(isc->sc_dev));
330
331 device_printf(isc->sc_dev, "Clock to USB host has been disabled\n");
332 }
333
334 int
omap_usb_port_mode(device_t dev,int port)335 omap_usb_port_mode(device_t dev, int port)
336 {
337 struct omap_uhh_softc *isc;
338
339 isc = device_get_softc(dev);
340 if ((port < 0) || (port >= OMAP_HS_USB_PORTS))
341 return (-1);
342
343 return isc->port_mode[port];
344 }
345
346 static int
omap_uhh_probe(device_t dev)347 omap_uhh_probe(device_t dev)
348 {
349
350 if (!ofw_bus_status_okay(dev))
351 return (ENXIO);
352
353 if (!ofw_bus_is_compatible(dev, "ti,usbhs-host"))
354 return (ENXIO);
355
356 device_set_desc(dev, "TI OMAP USB 2.0 Host module");
357
358 return (BUS_PROBE_DEFAULT);
359 }
360
361 static int
omap_uhh_attach(device_t dev)362 omap_uhh_attach(device_t dev)
363 {
364 struct omap_uhh_softc *isc = device_get_softc(dev);
365 int err;
366 int rid;
367 int i;
368 phandle_t node;
369 char propname[16];
370 char *mode;
371
372 /* save the device */
373 isc->sc_dev = dev;
374
375 /* Allocate resource for the UHH register set */
376 rid = 0;
377 isc->uhh_mem_res = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &rid, RF_ACTIVE);
378 if (!isc->uhh_mem_res) {
379 device_printf(dev, "Error: Could not map UHH memory\n");
380 goto error;
381 }
382
383 node = ofw_bus_get_node(dev);
384
385 if (node == -1)
386 goto error;
387
388 /* Get port modes from FDT */
389 for (i = 0; i < OMAP_HS_USB_PORTS; i++) {
390 isc->port_mode[i] = EHCI_HCD_OMAP_MODE_UNKNOWN;
391 snprintf(propname, sizeof(propname),
392 "port%d-mode", i+1);
393
394 if (OF_getprop_alloc(node, propname, (void**)&mode) <= 0)
395 continue;
396 if (strcmp(mode, "ehci-phy") == 0)
397 isc->port_mode[i] = EHCI_HCD_OMAP_MODE_PHY;
398 else if (strcmp(mode, "ehci-tll") == 0)
399 isc->port_mode[i] = EHCI_HCD_OMAP_MODE_TLL;
400 else if (strcmp(mode, "ehci-hsic") == 0)
401 isc->port_mode[i] = EHCI_HCD_OMAP_MODE_HSIC;
402 }
403
404 /* Initialise the ECHI registers */
405 err = omap_uhh_init(isc);
406 if (err) {
407 device_printf(dev, "Error: could not setup OMAP EHCI, %d\n", err);
408 goto error;
409 }
410
411 simplebus_init(dev, node);
412
413 /*
414 * Allow devices to identify.
415 */
416 bus_identify_children(dev);
417
418 /*
419 * Now walk the OFW tree and attach top-level devices.
420 */
421 for (node = OF_child(node); node > 0; node = OF_peer(node))
422 simplebus_add_device(dev, node, 0, NULL, -1, NULL);
423 bus_attach_children(dev);
424 return (0);
425
426 error:
427 omap_uhh_detach(dev);
428 return (ENXIO);
429 }
430
431 static int
omap_uhh_detach(device_t dev)432 omap_uhh_detach(device_t dev)
433 {
434 struct omap_uhh_softc *isc = device_get_softc(dev);
435
436 /* during module unload there are lots of children leftover */
437 device_delete_children(dev);
438
439 if (isc->uhh_mem_res) {
440 bus_release_resource(dev, SYS_RES_MEMORY, 0, isc->uhh_mem_res);
441 isc->uhh_mem_res = NULL;
442 }
443
444 omap_uhh_fini(isc);
445
446 return (0);
447 }
448
449 static device_method_t omap_uhh_methods[] = {
450 /* Device interface */
451 DEVMETHOD(device_probe, omap_uhh_probe),
452 DEVMETHOD(device_attach, omap_uhh_attach),
453 DEVMETHOD(device_detach, omap_uhh_detach),
454
455 DEVMETHOD(device_suspend, bus_generic_suspend),
456 DEVMETHOD(device_resume, bus_generic_resume),
457 DEVMETHOD(device_shutdown, bus_generic_shutdown),
458
459 DEVMETHOD_END
460 };
461
462 DEFINE_CLASS_1(omap_uhh, omap_uhh_driver, omap_uhh_methods,
463 sizeof(struct omap_uhh_softc), simplebus_driver);
464 DRIVER_MODULE(omap_uhh, simplebus, omap_uhh_driver, 0, 0);
465