1 // SPDX-License-Identifier: GPL-2.0-only
2 /* Copyright 2021 NXP */
3
4 #include <dt-bindings/firmware/imx/rsrc.h>
5 #include <linux/arm-smccc.h>
6 #include <linux/clk.h>
7 #include <linux/err.h>
8 #include <linux/firmware.h>
9 #include <linux/firmware/imx/sci.h>
10 #include <linux/interrupt.h>
11 #include <linux/kernel.h>
12 #include <linux/mailbox_client.h>
13 #include <linux/mfd/syscon.h>
14 #include <linux/module.h>
15 #include <linux/of.h>
16 #include <linux/of_reserved_mem.h>
17 #include <linux/platform_device.h>
18 #include <linux/pm_domain.h>
19 #include <linux/pm_runtime.h>
20 #include <linux/regmap.h>
21 #include <linux/remoteproc.h>
22 #include <linux/slab.h>
23
24 #include "imx_rproc.h"
25 #include "remoteproc_elf_helpers.h"
26 #include "remoteproc_internal.h"
27
28 #define DSP_RPROC_CLK_MAX 5
29
30 /*
31 * Module parameters
32 */
33 static unsigned int no_mailboxes;
34 module_param_named(no_mailboxes, no_mailboxes, int, 0644);
35 MODULE_PARM_DESC(no_mailboxes,
36 "There is no mailbox between cores, so ignore remote proc reply after start, default is 0 (off).");
37
38 #define REMOTE_IS_READY BIT(0)
39 #define REMOTE_READY_WAIT_MAX_RETRIES 500
40
41 /* att flags */
42 /* DSP own area */
43 #define ATT_OWN BIT(31)
44 /* DSP instruction area */
45 #define ATT_IRAM BIT(30)
46
47 /* Definitions for i.MX8MP */
48 /* DAP registers */
49 #define IMX8M_DAP_DEBUG 0x28800000
50 #define IMX8M_DAP_DEBUG_SIZE (64 * 1024)
51 #define IMX8M_DAP_PWRCTL (0x4000 + 0x3020)
52 #define IMX8M_PWRCTL_CORERESET BIT(16)
53
54 /* DSP audio mix registers */
55 #define IMX8M_AudioDSP_REG0 0x100
56 #define IMX8M_AudioDSP_REG1 0x104
57 #define IMX8M_AudioDSP_REG2 0x108
58 #define IMX8M_AudioDSP_REG3 0x10c
59
60 #define IMX8M_AudioDSP_REG2_RUNSTALL BIT(5)
61 #define IMX8M_AudioDSP_REG2_PWAITMODE BIT(1)
62
63 /* Definitions for i.MX8ULP */
64 #define IMX8ULP_SIM_LPAV_REG_SYSCTRL0 0x8
65 #define IMX8ULP_SYSCTRL0_DSP_DBG_RST BIT(25)
66 #define IMX8ULP_SYSCTRL0_DSP_PLAT_CLK_EN BIT(19)
67 #define IMX8ULP_SYSCTRL0_DSP_PBCLK_EN BIT(18)
68 #define IMX8ULP_SYSCTRL0_DSP_CLK_EN BIT(17)
69 #define IMX8ULP_SYSCTRL0_DSP_RST BIT(16)
70 #define IMX8ULP_SYSCTRL0_DSP_OCD_HALT BIT(14)
71 #define IMX8ULP_SYSCTRL0_DSP_STALL BIT(13)
72
73 #define IMX8ULP_SIP_HIFI_XRDC 0xc200000e
74
75 /*
76 * enum - Predefined Mailbox Messages
77 *
78 * @RP_MBOX_SUSPEND_SYSTEM: system suspend request for the remote processor
79 *
80 * @RP_MBOX_SUSPEND_ACK: successful response from remote processor for a
81 * suspend request
82 *
83 * @RP_MBOX_RESUME_SYSTEM: system resume request for the remote processor
84 *
85 * @RP_MBOX_RESUME_ACK: successful response from remote processor for a
86 * resume request
87 */
88 enum imx_dsp_rp_mbox_messages {
89 RP_MBOX_SUSPEND_SYSTEM = 0xFF11,
90 RP_MBOX_SUSPEND_ACK = 0xFF12,
91 RP_MBOX_RESUME_SYSTEM = 0xFF13,
92 RP_MBOX_RESUME_ACK = 0xFF14,
93 };
94
95 /**
96 * struct imx_dsp_rproc - DSP remote processor state
97 * @regmap: regmap handler
98 * @rproc: rproc handler
99 * @dsp_dcfg: device configuration pointer
100 * @clks: clocks needed by this device
101 * @cl: mailbox client to request the mailbox channel
102 * @cl_rxdb: mailbox client to request the mailbox channel for doorbell
103 * @tx_ch: mailbox tx channel handle
104 * @rx_ch: mailbox rx channel handle
105 * @rxdb_ch: mailbox rx doorbell channel handle
106 * @pd_list: power domain list
107 * @ipc_handle: System Control Unit ipc handle
108 * @rproc_work: work for processing virtio interrupts
109 * @pm_comp: completion primitive to sync for suspend response
110 * @flags: control flags
111 */
112 struct imx_dsp_rproc {
113 struct regmap *regmap;
114 struct rproc *rproc;
115 const struct imx_dsp_rproc_dcfg *dsp_dcfg;
116 struct clk_bulk_data clks[DSP_RPROC_CLK_MAX];
117 struct mbox_client cl;
118 struct mbox_client cl_rxdb;
119 struct mbox_chan *tx_ch;
120 struct mbox_chan *rx_ch;
121 struct mbox_chan *rxdb_ch;
122 struct dev_pm_domain_list *pd_list;
123 struct imx_sc_ipc *ipc_handle;
124 struct work_struct rproc_work;
125 struct completion pm_comp;
126 u32 flags;
127 };
128
129 /**
130 * struct imx_dsp_rproc_dcfg - DSP remote processor configuration
131 * @dcfg: imx_rproc_dcfg handler
132 * @reset: reset callback function
133 */
134 struct imx_dsp_rproc_dcfg {
135 const struct imx_rproc_dcfg *dcfg;
136 int (*reset)(struct imx_dsp_rproc *priv);
137 };
138
139 static const struct imx_rproc_att imx_dsp_rproc_att_imx8qm[] = {
140 /* dev addr , sys addr , size , flags */
141 { 0x596e8000, 0x556e8000, 0x00008000, ATT_OWN },
142 { 0x596f0000, 0x556f0000, 0x00008000, ATT_OWN },
143 { 0x596f8000, 0x556f8000, 0x00000800, ATT_OWN | ATT_IRAM},
144 { 0x55700000, 0x55700000, 0x00070000, ATT_OWN },
145 /* DDR (Data) */
146 { 0x80000000, 0x80000000, 0x60000000, 0},
147 };
148
149 static const struct imx_rproc_att imx_dsp_rproc_att_imx8qxp[] = {
150 /* dev addr , sys addr , size , flags */
151 { 0x596e8000, 0x596e8000, 0x00008000, ATT_OWN },
152 { 0x596f0000, 0x596f0000, 0x00008000, ATT_OWN },
153 { 0x596f8000, 0x596f8000, 0x00000800, ATT_OWN | ATT_IRAM},
154 { 0x59700000, 0x59700000, 0x00070000, ATT_OWN },
155 /* DDR (Data) */
156 { 0x80000000, 0x80000000, 0x60000000, 0},
157 };
158
159 static const struct imx_rproc_att imx_dsp_rproc_att_imx8mp[] = {
160 /* dev addr , sys addr , size , flags */
161 { 0x3b6e8000, 0x3b6e8000, 0x00008000, ATT_OWN },
162 { 0x3b6f0000, 0x3b6f0000, 0x00008000, ATT_OWN },
163 { 0x3b6f8000, 0x3b6f8000, 0x00000800, ATT_OWN | ATT_IRAM},
164 { 0x3b700000, 0x3b700000, 0x00040000, ATT_OWN },
165 /* DDR (Data) */
166 { 0x40000000, 0x40000000, 0x80000000, 0},
167 };
168
169 static const struct imx_rproc_att imx_dsp_rproc_att_imx8ulp[] = {
170 /* dev addr , sys addr , size , flags */
171 { 0x21170000, 0x21170000, 0x00010000, ATT_OWN | ATT_IRAM},
172 { 0x21180000, 0x21180000, 0x00010000, ATT_OWN },
173 /* DDR (Data) */
174 { 0x0c000000, 0x80000000, 0x10000000, 0},
175 { 0x30000000, 0x90000000, 0x10000000, 0},
176 };
177
178 /* Initialize the mailboxes between cores, if exists */
179 static int (*imx_dsp_rproc_mbox_init)(struct imx_dsp_rproc *priv);
180
181 /* Reset function for DSP on i.MX8MP */
imx8mp_dsp_reset(struct imx_dsp_rproc * priv)182 static int imx8mp_dsp_reset(struct imx_dsp_rproc *priv)
183 {
184 void __iomem *dap = ioremap_wc(IMX8M_DAP_DEBUG, IMX8M_DAP_DEBUG_SIZE);
185 int pwrctl;
186
187 /* Put DSP into reset and stall */
188 pwrctl = readl(dap + IMX8M_DAP_PWRCTL);
189 pwrctl |= IMX8M_PWRCTL_CORERESET;
190 writel(pwrctl, dap + IMX8M_DAP_PWRCTL);
191
192 /* Keep reset asserted for 10 cycles */
193 usleep_range(1, 2);
194
195 regmap_update_bits(priv->regmap, IMX8M_AudioDSP_REG2,
196 IMX8M_AudioDSP_REG2_RUNSTALL,
197 IMX8M_AudioDSP_REG2_RUNSTALL);
198
199 /* Take the DSP out of reset and keep stalled for FW loading */
200 pwrctl = readl(dap + IMX8M_DAP_PWRCTL);
201 pwrctl &= ~IMX8M_PWRCTL_CORERESET;
202 writel(pwrctl, dap + IMX8M_DAP_PWRCTL);
203
204 iounmap(dap);
205 return 0;
206 }
207
208 /* Reset function for DSP on i.MX8ULP */
imx8ulp_dsp_reset(struct imx_dsp_rproc * priv)209 static int imx8ulp_dsp_reset(struct imx_dsp_rproc *priv)
210 {
211 struct arm_smccc_res res;
212
213 /* Put DSP into reset and stall */
214 regmap_update_bits(priv->regmap, IMX8ULP_SIM_LPAV_REG_SYSCTRL0,
215 IMX8ULP_SYSCTRL0_DSP_RST, IMX8ULP_SYSCTRL0_DSP_RST);
216 regmap_update_bits(priv->regmap, IMX8ULP_SIM_LPAV_REG_SYSCTRL0,
217 IMX8ULP_SYSCTRL0_DSP_STALL,
218 IMX8ULP_SYSCTRL0_DSP_STALL);
219
220 /* Configure resources of DSP through TFA */
221 arm_smccc_smc(IMX8ULP_SIP_HIFI_XRDC, 0, 0, 0, 0, 0, 0, 0, &res);
222
223 /* Take the DSP out of reset and keep stalled for FW loading */
224 regmap_update_bits(priv->regmap, IMX8ULP_SIM_LPAV_REG_SYSCTRL0,
225 IMX8ULP_SYSCTRL0_DSP_RST, 0);
226 regmap_update_bits(priv->regmap, IMX8ULP_SIM_LPAV_REG_SYSCTRL0,
227 IMX8ULP_SYSCTRL0_DSP_DBG_RST, 0);
228
229 return 0;
230 }
231
232 /* Specific configuration for i.MX8MP */
233 static const struct imx_rproc_dcfg dsp_rproc_cfg_imx8mp = {
234 .src_reg = IMX8M_AudioDSP_REG2,
235 .src_mask = IMX8M_AudioDSP_REG2_RUNSTALL,
236 .src_start = 0,
237 .src_stop = IMX8M_AudioDSP_REG2_RUNSTALL,
238 .att = imx_dsp_rproc_att_imx8mp,
239 .att_size = ARRAY_SIZE(imx_dsp_rproc_att_imx8mp),
240 .method = IMX_RPROC_MMIO,
241 };
242
243 static const struct imx_dsp_rproc_dcfg imx_dsp_rproc_cfg_imx8mp = {
244 .dcfg = &dsp_rproc_cfg_imx8mp,
245 .reset = imx8mp_dsp_reset,
246 };
247
248 /* Specific configuration for i.MX8ULP */
249 static const struct imx_rproc_dcfg dsp_rproc_cfg_imx8ulp = {
250 .src_reg = IMX8ULP_SIM_LPAV_REG_SYSCTRL0,
251 .src_mask = IMX8ULP_SYSCTRL0_DSP_STALL,
252 .src_start = 0,
253 .src_stop = IMX8ULP_SYSCTRL0_DSP_STALL,
254 .att = imx_dsp_rproc_att_imx8ulp,
255 .att_size = ARRAY_SIZE(imx_dsp_rproc_att_imx8ulp),
256 .method = IMX_RPROC_MMIO,
257 };
258
259 static const struct imx_dsp_rproc_dcfg imx_dsp_rproc_cfg_imx8ulp = {
260 .dcfg = &dsp_rproc_cfg_imx8ulp,
261 .reset = imx8ulp_dsp_reset,
262 };
263
264 /* Specific configuration for i.MX8QXP */
265 static const struct imx_rproc_dcfg dsp_rproc_cfg_imx8qxp = {
266 .att = imx_dsp_rproc_att_imx8qxp,
267 .att_size = ARRAY_SIZE(imx_dsp_rproc_att_imx8qxp),
268 .method = IMX_RPROC_SCU_API,
269 };
270
271 static const struct imx_dsp_rproc_dcfg imx_dsp_rproc_cfg_imx8qxp = {
272 .dcfg = &dsp_rproc_cfg_imx8qxp,
273 };
274
275 /* Specific configuration for i.MX8QM */
276 static const struct imx_rproc_dcfg dsp_rproc_cfg_imx8qm = {
277 .att = imx_dsp_rproc_att_imx8qm,
278 .att_size = ARRAY_SIZE(imx_dsp_rproc_att_imx8qm),
279 .method = IMX_RPROC_SCU_API,
280 };
281
282 static const struct imx_dsp_rproc_dcfg imx_dsp_rproc_cfg_imx8qm = {
283 .dcfg = &dsp_rproc_cfg_imx8qm,
284 };
285
imx_dsp_rproc_ready(struct rproc * rproc)286 static int imx_dsp_rproc_ready(struct rproc *rproc)
287 {
288 struct imx_dsp_rproc *priv = rproc->priv;
289 int i;
290
291 if (!priv->rxdb_ch)
292 return 0;
293
294 for (i = 0; i < REMOTE_READY_WAIT_MAX_RETRIES; i++) {
295 if (priv->flags & REMOTE_IS_READY)
296 return 0;
297 usleep_range(100, 200);
298 }
299
300 return -ETIMEDOUT;
301 }
302
303 /*
304 * Start function for rproc_ops
305 *
306 * There is a handshake for start procedure: when DSP starts, it
307 * will send a doorbell message to this driver, then the
308 * REMOTE_IS_READY flags is set, then driver will kick
309 * a message to DSP.
310 */
imx_dsp_rproc_start(struct rproc * rproc)311 static int imx_dsp_rproc_start(struct rproc *rproc)
312 {
313 struct imx_dsp_rproc *priv = rproc->priv;
314 const struct imx_dsp_rproc_dcfg *dsp_dcfg = priv->dsp_dcfg;
315 const struct imx_rproc_dcfg *dcfg = dsp_dcfg->dcfg;
316 struct device *dev = rproc->dev.parent;
317 int ret;
318
319 switch (dcfg->method) {
320 case IMX_RPROC_MMIO:
321 ret = regmap_update_bits(priv->regmap,
322 dcfg->src_reg,
323 dcfg->src_mask,
324 dcfg->src_start);
325 break;
326 case IMX_RPROC_SCU_API:
327 ret = imx_sc_pm_cpu_start(priv->ipc_handle,
328 IMX_SC_R_DSP,
329 true,
330 rproc->bootaddr);
331 break;
332 default:
333 return -EOPNOTSUPP;
334 }
335
336 if (ret)
337 dev_err(dev, "Failed to enable remote core!\n");
338 else
339 ret = imx_dsp_rproc_ready(rproc);
340
341 return ret;
342 }
343
344 /*
345 * Stop function for rproc_ops
346 * It clears the REMOTE_IS_READY flags
347 */
imx_dsp_rproc_stop(struct rproc * rproc)348 static int imx_dsp_rproc_stop(struct rproc *rproc)
349 {
350 struct imx_dsp_rproc *priv = rproc->priv;
351 const struct imx_dsp_rproc_dcfg *dsp_dcfg = priv->dsp_dcfg;
352 const struct imx_rproc_dcfg *dcfg = dsp_dcfg->dcfg;
353 struct device *dev = rproc->dev.parent;
354 int ret = 0;
355
356 if (rproc->state == RPROC_CRASHED) {
357 priv->flags &= ~REMOTE_IS_READY;
358 return 0;
359 }
360
361 switch (dcfg->method) {
362 case IMX_RPROC_MMIO:
363 ret = regmap_update_bits(priv->regmap, dcfg->src_reg, dcfg->src_mask,
364 dcfg->src_stop);
365 break;
366 case IMX_RPROC_SCU_API:
367 ret = imx_sc_pm_cpu_start(priv->ipc_handle,
368 IMX_SC_R_DSP,
369 false,
370 rproc->bootaddr);
371 break;
372 default:
373 return -EOPNOTSUPP;
374 }
375
376 if (ret)
377 dev_err(dev, "Failed to stop remote core\n");
378 else
379 priv->flags &= ~REMOTE_IS_READY;
380
381 return ret;
382 }
383
384 /**
385 * imx_dsp_rproc_sys_to_da() - internal memory translation helper
386 * @priv: private data pointer
387 * @sys: system address (DDR address)
388 * @len: length of the memory buffer
389 * @da: device address to translate
390 *
391 * Convert system address (DDR address) to device address (DSP)
392 * for there may be memory remap for device.
393 */
imx_dsp_rproc_sys_to_da(struct imx_dsp_rproc * priv,u64 sys,size_t len,u64 * da)394 static int imx_dsp_rproc_sys_to_da(struct imx_dsp_rproc *priv, u64 sys,
395 size_t len, u64 *da)
396 {
397 const struct imx_dsp_rproc_dcfg *dsp_dcfg = priv->dsp_dcfg;
398 const struct imx_rproc_dcfg *dcfg = dsp_dcfg->dcfg;
399 int i;
400
401 /* Parse address translation table */
402 for (i = 0; i < dcfg->att_size; i++) {
403 const struct imx_rproc_att *att = &dcfg->att[i];
404
405 if (sys >= att->sa && sys + len <= att->sa + att->size) {
406 unsigned int offset = sys - att->sa;
407
408 *da = att->da + offset;
409 return 0;
410 }
411 }
412
413 return -ENOENT;
414 }
415
416 /* Main virtqueue message work function
417 *
418 * This function is executed upon scheduling of the i.MX DSP remoteproc
419 * driver's workqueue. The workqueue is scheduled by the mailbox rx
420 * handler.
421 *
422 * This work function processes both the Tx and Rx virtqueue indices on
423 * every invocation. The rproc_vq_interrupt function can detect if there
424 * are new unprocessed messages or not (returns IRQ_NONE vs IRQ_HANDLED),
425 * but there is no need to check for these return values. The index 0
426 * triggering will process all pending Rx buffers, and the index 1 triggering
427 * will process all newly available Tx buffers and will wakeup any potentially
428 * blocked senders.
429 *
430 * NOTE:
431 * The current logic is based on an inherent design assumption of supporting
432 * only 2 vrings, but this can be changed if needed.
433 */
imx_dsp_rproc_vq_work(struct work_struct * work)434 static void imx_dsp_rproc_vq_work(struct work_struct *work)
435 {
436 struct imx_dsp_rproc *priv = container_of(work, struct imx_dsp_rproc,
437 rproc_work);
438 struct rproc *rproc = priv->rproc;
439
440 mutex_lock(&rproc->lock);
441
442 if (rproc->state != RPROC_RUNNING)
443 goto unlock_mutex;
444
445 rproc_vq_interrupt(priv->rproc, 0);
446 rproc_vq_interrupt(priv->rproc, 1);
447
448 unlock_mutex:
449 mutex_unlock(&rproc->lock);
450 }
451
452 /**
453 * imx_dsp_rproc_rx_tx_callback() - inbound mailbox message handler
454 * @cl: mailbox client pointer used for requesting the mailbox channel
455 * @data: mailbox payload
456 *
457 * This handler is invoked by mailbox driver whenever a mailbox
458 * message is received. Usually, the SUSPEND and RESUME related messages
459 * are handled in this function, other messages are handled by remoteproc core
460 */
imx_dsp_rproc_rx_tx_callback(struct mbox_client * cl,void * data)461 static void imx_dsp_rproc_rx_tx_callback(struct mbox_client *cl, void *data)
462 {
463 struct rproc *rproc = dev_get_drvdata(cl->dev);
464 struct imx_dsp_rproc *priv = rproc->priv;
465 struct device *dev = rproc->dev.parent;
466 u32 message = (u32)(*(u32 *)data);
467
468 dev_dbg(dev, "mbox msg: 0x%x\n", message);
469
470 switch (message) {
471 case RP_MBOX_SUSPEND_ACK:
472 complete(&priv->pm_comp);
473 break;
474 case RP_MBOX_RESUME_ACK:
475 complete(&priv->pm_comp);
476 break;
477 default:
478 schedule_work(&priv->rproc_work);
479 break;
480 }
481 }
482
483 /**
484 * imx_dsp_rproc_rxdb_callback() - inbound mailbox message handler
485 * @cl: mailbox client pointer used for requesting the mailbox channel
486 * @data: mailbox payload
487 *
488 * For doorbell, there is no message specified, just set REMOTE_IS_READY
489 * flag.
490 */
imx_dsp_rproc_rxdb_callback(struct mbox_client * cl,void * data)491 static void imx_dsp_rproc_rxdb_callback(struct mbox_client *cl, void *data)
492 {
493 struct rproc *rproc = dev_get_drvdata(cl->dev);
494 struct imx_dsp_rproc *priv = rproc->priv;
495
496 /* Remote is ready after firmware is loaded and running */
497 priv->flags |= REMOTE_IS_READY;
498 }
499
500 /**
501 * imx_dsp_rproc_mbox_alloc() - request mailbox channels
502 * @priv: private data pointer
503 *
504 * Request three mailbox channels (tx, rx, rxdb).
505 */
imx_dsp_rproc_mbox_alloc(struct imx_dsp_rproc * priv)506 static int imx_dsp_rproc_mbox_alloc(struct imx_dsp_rproc *priv)
507 {
508 struct device *dev = priv->rproc->dev.parent;
509 struct mbox_client *cl;
510 int ret;
511
512 if (!of_property_present(dev->of_node, "mbox-names"))
513 return 0;
514
515 cl = &priv->cl;
516 cl->dev = dev;
517 cl->tx_block = true;
518 cl->tx_tout = 100;
519 cl->knows_txdone = false;
520 cl->rx_callback = imx_dsp_rproc_rx_tx_callback;
521
522 /* Channel for sending message */
523 priv->tx_ch = mbox_request_channel_byname(cl, "tx");
524 if (IS_ERR(priv->tx_ch)) {
525 ret = PTR_ERR(priv->tx_ch);
526 dev_dbg(cl->dev, "failed to request tx mailbox channel: %d\n",
527 ret);
528 return ret;
529 }
530
531 /* Channel for receiving message */
532 priv->rx_ch = mbox_request_channel_byname(cl, "rx");
533 if (IS_ERR(priv->rx_ch)) {
534 ret = PTR_ERR(priv->rx_ch);
535 dev_dbg(cl->dev, "failed to request rx mailbox channel: %d\n",
536 ret);
537 goto free_channel_tx;
538 }
539
540 cl = &priv->cl_rxdb;
541 cl->dev = dev;
542 cl->rx_callback = imx_dsp_rproc_rxdb_callback;
543
544 /*
545 * RX door bell is used to receive the ready signal from remote
546 * after firmware loaded.
547 */
548 priv->rxdb_ch = mbox_request_channel_byname(cl, "rxdb");
549 if (IS_ERR(priv->rxdb_ch)) {
550 ret = PTR_ERR(priv->rxdb_ch);
551 dev_dbg(cl->dev, "failed to request mbox chan rxdb, ret %d\n",
552 ret);
553 goto free_channel_rx;
554 }
555
556 return 0;
557
558 free_channel_rx:
559 mbox_free_channel(priv->rx_ch);
560 free_channel_tx:
561 mbox_free_channel(priv->tx_ch);
562 return ret;
563 }
564
565 /*
566 * imx_dsp_rproc_mbox_no_alloc()
567 *
568 * Empty function for no mailbox between cores
569 *
570 * Always return 0
571 */
imx_dsp_rproc_mbox_no_alloc(struct imx_dsp_rproc * priv)572 static int imx_dsp_rproc_mbox_no_alloc(struct imx_dsp_rproc *priv)
573 {
574 return 0;
575 }
576
imx_dsp_rproc_free_mbox(struct imx_dsp_rproc * priv)577 static void imx_dsp_rproc_free_mbox(struct imx_dsp_rproc *priv)
578 {
579 mbox_free_channel(priv->tx_ch);
580 mbox_free_channel(priv->rx_ch);
581 mbox_free_channel(priv->rxdb_ch);
582 }
583
584 /**
585 * imx_dsp_rproc_add_carveout() - request mailbox channels
586 * @priv: private data pointer
587 *
588 * This function registers specified memory entry in @rproc carveouts list
589 * The carveouts can help to mapping the memory address for DSP.
590 */
imx_dsp_rproc_add_carveout(struct imx_dsp_rproc * priv)591 static int imx_dsp_rproc_add_carveout(struct imx_dsp_rproc *priv)
592 {
593 const struct imx_dsp_rproc_dcfg *dsp_dcfg = priv->dsp_dcfg;
594 const struct imx_rproc_dcfg *dcfg = dsp_dcfg->dcfg;
595 struct rproc *rproc = priv->rproc;
596 struct device *dev = rproc->dev.parent;
597 struct device_node *np = dev->of_node;
598 struct of_phandle_iterator it;
599 struct rproc_mem_entry *mem;
600 struct reserved_mem *rmem;
601 void __iomem *cpu_addr;
602 int a;
603 u64 da;
604
605 /* Remap required addresses */
606 for (a = 0; a < dcfg->att_size; a++) {
607 const struct imx_rproc_att *att = &dcfg->att[a];
608
609 if (!(att->flags & ATT_OWN))
610 continue;
611
612 if (imx_dsp_rproc_sys_to_da(priv, att->sa, att->size, &da))
613 return -EINVAL;
614
615 cpu_addr = devm_ioremap_wc(dev, att->sa, att->size);
616 if (!cpu_addr) {
617 dev_err(dev, "failed to map memory %p\n", &att->sa);
618 return -ENOMEM;
619 }
620
621 /* Register memory region */
622 mem = rproc_mem_entry_init(dev, (void __force *)cpu_addr, (dma_addr_t)att->sa,
623 att->size, da, NULL, NULL, "dsp_mem");
624
625 if (mem)
626 rproc_coredump_add_segment(rproc, da, att->size);
627 else
628 return -ENOMEM;
629
630 rproc_add_carveout(rproc, mem);
631 }
632
633 of_phandle_iterator_init(&it, np, "memory-region", NULL, 0);
634 while (of_phandle_iterator_next(&it) == 0) {
635 /*
636 * Ignore the first memory region which will be used vdev buffer.
637 * No need to do extra handlings, rproc_add_virtio_dev will handle it.
638 */
639 if (!strcmp(it.node->name, "vdev0buffer"))
640 continue;
641
642 rmem = of_reserved_mem_lookup(it.node);
643 if (!rmem) {
644 of_node_put(it.node);
645 dev_err(dev, "unable to acquire memory-region\n");
646 return -EINVAL;
647 }
648
649 if (imx_dsp_rproc_sys_to_da(priv, rmem->base, rmem->size, &da)) {
650 of_node_put(it.node);
651 return -EINVAL;
652 }
653
654 cpu_addr = devm_ioremap_wc(dev, rmem->base, rmem->size);
655 if (!cpu_addr) {
656 of_node_put(it.node);
657 dev_err(dev, "failed to map memory %p\n", &rmem->base);
658 return -ENOMEM;
659 }
660
661 /* Register memory region */
662 mem = rproc_mem_entry_init(dev, (void __force *)cpu_addr, (dma_addr_t)rmem->base,
663 rmem->size, da, NULL, NULL, it.node->name);
664
665 if (mem) {
666 rproc_coredump_add_segment(rproc, da, rmem->size);
667 } else {
668 of_node_put(it.node);
669 return -ENOMEM;
670 }
671
672 rproc_add_carveout(rproc, mem);
673 }
674
675 return 0;
676 }
677
678 /* Prepare function for rproc_ops */
imx_dsp_rproc_prepare(struct rproc * rproc)679 static int imx_dsp_rproc_prepare(struct rproc *rproc)
680 {
681 struct imx_dsp_rproc *priv = rproc->priv;
682 struct device *dev = rproc->dev.parent;
683 struct rproc_mem_entry *carveout;
684 int ret;
685
686 ret = imx_dsp_rproc_add_carveout(priv);
687 if (ret) {
688 dev_err(dev, "failed on imx_dsp_rproc_add_carveout\n");
689 return ret;
690 }
691
692 pm_runtime_get_sync(dev);
693
694 /*
695 * Clear buffers after pm rumtime for internal ocram is not
696 * accessible if power and clock are not enabled.
697 */
698 list_for_each_entry(carveout, &rproc->carveouts, node) {
699 if (carveout->va)
700 memset(carveout->va, 0, carveout->len);
701 }
702
703 return 0;
704 }
705
706 /* Unprepare function for rproc_ops */
imx_dsp_rproc_unprepare(struct rproc * rproc)707 static int imx_dsp_rproc_unprepare(struct rproc *rproc)
708 {
709 pm_runtime_put_sync(rproc->dev.parent);
710
711 return 0;
712 }
713
714 /* Kick function for rproc_ops */
imx_dsp_rproc_kick(struct rproc * rproc,int vqid)715 static void imx_dsp_rproc_kick(struct rproc *rproc, int vqid)
716 {
717 struct imx_dsp_rproc *priv = rproc->priv;
718 struct device *dev = rproc->dev.parent;
719 int err;
720 __u32 mmsg;
721
722 if (!priv->tx_ch) {
723 dev_err(dev, "No initialized mbox tx channel\n");
724 return;
725 }
726
727 /*
728 * Send the index of the triggered virtqueue as the mu payload.
729 * Let remote processor know which virtqueue is used.
730 */
731 mmsg = vqid;
732
733 err = mbox_send_message(priv->tx_ch, (void *)&mmsg);
734 if (err < 0)
735 dev_err(dev, "%s: failed (%d, err:%d)\n", __func__, vqid, err);
736 }
737
738 /*
739 * Custom memory copy implementation for i.MX DSP Cores
740 *
741 * The IRAM is part of the HiFi DSP.
742 * According to hw specs only 32-bits writes are allowed.
743 */
imx_dsp_rproc_memcpy(void * dst,const void * src,size_t size)744 static int imx_dsp_rproc_memcpy(void *dst, const void *src, size_t size)
745 {
746 void __iomem *dest = (void __iomem *)dst;
747 const u8 *src_byte = src;
748 const u32 *source = src;
749 u32 affected_mask;
750 int i, q, r;
751 u32 tmp;
752
753 /* destination must be 32bit aligned */
754 if (!IS_ALIGNED((uintptr_t)dest, 4))
755 return -EINVAL;
756
757 q = size / 4;
758 r = size % 4;
759
760 /* copy data in units of 32 bits at a time */
761 for (i = 0; i < q; i++)
762 writel(source[i], dest + i * 4);
763
764 if (r) {
765 affected_mask = GENMASK(8 * r, 0);
766
767 /*
768 * first read the 32bit data of dest, then change affected
769 * bytes, and write back to dest.
770 * For unaffected bytes, it should not be changed
771 */
772 tmp = readl(dest + q * 4);
773 tmp &= ~affected_mask;
774
775 /* avoid reading after end of source */
776 for (i = 0; i < r; i++)
777 tmp |= (src_byte[q * 4 + i] << (8 * i));
778
779 writel(tmp, dest + q * 4);
780 }
781
782 return 0;
783 }
784
785 /*
786 * Custom memset implementation for i.MX DSP Cores
787 *
788 * The IRAM is part of the HiFi DSP.
789 * According to hw specs only 32-bits writes are allowed.
790 */
imx_dsp_rproc_memset(void * addr,u8 value,size_t size)791 static int imx_dsp_rproc_memset(void *addr, u8 value, size_t size)
792 {
793 void __iomem *tmp_dst = (void __iomem *)addr;
794 u32 tmp_val = value;
795 u32 affected_mask;
796 int q, r;
797 u32 tmp;
798
799 /* destination must be 32bit aligned */
800 if (!IS_ALIGNED((uintptr_t)addr, 4))
801 return -EINVAL;
802
803 tmp_val |= tmp_val << 8;
804 tmp_val |= tmp_val << 16;
805
806 q = size / 4;
807 r = size % 4;
808
809 while (q--)
810 writel(tmp_val, tmp_dst++);
811
812 if (r) {
813 affected_mask = GENMASK(8 * r, 0);
814
815 /*
816 * first read the 32bit data of addr, then change affected
817 * bytes, and write back to addr.
818 * For unaffected bytes, it should not be changed
819 */
820 tmp = readl(tmp_dst);
821 tmp &= ~affected_mask;
822
823 tmp |= (tmp_val & affected_mask);
824 writel(tmp, tmp_dst);
825 }
826
827 return 0;
828 }
829
830 /*
831 * imx_dsp_rproc_elf_load_segments() - load firmware segments to memory
832 * @rproc: remote processor which will be booted using these fw segments
833 * @fw: the ELF firmware image
834 *
835 * This function loads the firmware segments to memory, where the remote
836 * processor expects them.
837 *
838 * Return: 0 on success and an appropriate error code otherwise
839 */
imx_dsp_rproc_elf_load_segments(struct rproc * rproc,const struct firmware * fw)840 static int imx_dsp_rproc_elf_load_segments(struct rproc *rproc, const struct firmware *fw)
841 {
842 struct device *dev = &rproc->dev;
843 const void *ehdr, *phdr;
844 int i, ret = 0;
845 u16 phnum;
846 const u8 *elf_data = fw->data;
847 u8 class = fw_elf_get_class(fw);
848 u32 elf_phdr_get_size = elf_size_of_phdr(class);
849
850 ehdr = elf_data;
851 phnum = elf_hdr_get_e_phnum(class, ehdr);
852 phdr = elf_data + elf_hdr_get_e_phoff(class, ehdr);
853
854 /* go through the available ELF segments */
855 for (i = 0; i < phnum; i++, phdr += elf_phdr_get_size) {
856 u64 da = elf_phdr_get_p_paddr(class, phdr);
857 u64 memsz = elf_phdr_get_p_memsz(class, phdr);
858 u64 filesz = elf_phdr_get_p_filesz(class, phdr);
859 u64 offset = elf_phdr_get_p_offset(class, phdr);
860 u32 type = elf_phdr_get_p_type(class, phdr);
861 void *ptr;
862
863 if (type != PT_LOAD || !memsz)
864 continue;
865
866 dev_dbg(dev, "phdr: type %d da 0x%llx memsz 0x%llx filesz 0x%llx\n",
867 type, da, memsz, filesz);
868
869 if (filesz > memsz) {
870 dev_err(dev, "bad phdr filesz 0x%llx memsz 0x%llx\n",
871 filesz, memsz);
872 ret = -EINVAL;
873 break;
874 }
875
876 if (offset + filesz > fw->size) {
877 dev_err(dev, "truncated fw: need 0x%llx avail 0x%zx\n",
878 offset + filesz, fw->size);
879 ret = -EINVAL;
880 break;
881 }
882
883 if (!rproc_u64_fit_in_size_t(memsz)) {
884 dev_err(dev, "size (%llx) does not fit in size_t type\n",
885 memsz);
886 ret = -EOVERFLOW;
887 break;
888 }
889
890 /* grab the kernel address for this device address */
891 ptr = rproc_da_to_va(rproc, da, memsz, NULL);
892 if (!ptr) {
893 dev_err(dev, "bad phdr da 0x%llx mem 0x%llx\n", da,
894 memsz);
895 ret = -EINVAL;
896 break;
897 }
898
899 /* put the segment where the remote processor expects it */
900 if (filesz) {
901 ret = imx_dsp_rproc_memcpy(ptr, elf_data + offset, filesz);
902 if (ret) {
903 dev_err(dev, "memory copy failed for da 0x%llx memsz 0x%llx\n",
904 da, memsz);
905 break;
906 }
907 }
908
909 /* zero out remaining memory for this segment */
910 if (memsz > filesz) {
911 ret = imx_dsp_rproc_memset(ptr + filesz, 0, memsz - filesz);
912 if (ret) {
913 dev_err(dev, "memset failed for da 0x%llx memsz 0x%llx\n",
914 da, memsz);
915 break;
916 }
917 }
918 }
919
920 return ret;
921 }
922
imx_dsp_rproc_parse_fw(struct rproc * rproc,const struct firmware * fw)923 static int imx_dsp_rproc_parse_fw(struct rproc *rproc, const struct firmware *fw)
924 {
925 if (rproc_elf_load_rsc_table(rproc, fw))
926 dev_warn(&rproc->dev, "no resource table found for this firmware\n");
927
928 return 0;
929 }
930
931 static const struct rproc_ops imx_dsp_rproc_ops = {
932 .prepare = imx_dsp_rproc_prepare,
933 .unprepare = imx_dsp_rproc_unprepare,
934 .start = imx_dsp_rproc_start,
935 .stop = imx_dsp_rproc_stop,
936 .kick = imx_dsp_rproc_kick,
937 .load = imx_dsp_rproc_elf_load_segments,
938 .parse_fw = imx_dsp_rproc_parse_fw,
939 .find_loaded_rsc_table = rproc_elf_find_loaded_rsc_table,
940 .sanity_check = rproc_elf_sanity_check,
941 .get_boot_addr = rproc_elf_get_boot_addr,
942 };
943
944 /**
945 * imx_dsp_attach_pm_domains() - attach the power domains
946 * @priv: private data pointer
947 *
948 * On i.MX8QM and i.MX8QXP there is multiple power domains
949 * required, so need to link them.
950 */
imx_dsp_attach_pm_domains(struct imx_dsp_rproc * priv)951 static int imx_dsp_attach_pm_domains(struct imx_dsp_rproc *priv)
952 {
953 struct device *dev = priv->rproc->dev.parent;
954 int ret;
955
956 /* A single PM domain is already attached. */
957 if (dev->pm_domain)
958 return 0;
959
960 ret = dev_pm_domain_attach_list(dev, NULL, &priv->pd_list);
961 return ret < 0 ? ret : 0;
962 }
963
964 /**
965 * imx_dsp_rproc_detect_mode() - detect DSP control mode
966 * @priv: private data pointer
967 *
968 * Different platform has different control method for DSP, which depends
969 * on how the DSP is integrated in platform.
970 *
971 * For i.MX8QXP and i.MX8QM, DSP should be started and stopped by System
972 * Control Unit.
973 * For i.MX8MP and i.MX8ULP, DSP should be started and stopped by system
974 * integration module.
975 */
imx_dsp_rproc_detect_mode(struct imx_dsp_rproc * priv)976 static int imx_dsp_rproc_detect_mode(struct imx_dsp_rproc *priv)
977 {
978 const struct imx_dsp_rproc_dcfg *dsp_dcfg = priv->dsp_dcfg;
979 struct device *dev = priv->rproc->dev.parent;
980 struct regmap *regmap;
981 int ret = 0;
982
983 switch (dsp_dcfg->dcfg->method) {
984 case IMX_RPROC_SCU_API:
985 ret = imx_scu_get_handle(&priv->ipc_handle);
986 if (ret)
987 return ret;
988 break;
989 case IMX_RPROC_MMIO:
990 regmap = syscon_regmap_lookup_by_phandle(dev->of_node, "fsl,dsp-ctrl");
991 if (IS_ERR(regmap)) {
992 dev_err(dev, "failed to find syscon\n");
993 return PTR_ERR(regmap);
994 }
995
996 priv->regmap = regmap;
997 break;
998 default:
999 ret = -EOPNOTSUPP;
1000 break;
1001 }
1002
1003 return ret;
1004 }
1005
1006 static const char *imx_dsp_clks_names[DSP_RPROC_CLK_MAX] = {
1007 /* DSP clocks */
1008 "core", "ocram", "debug", "ipg", "mu",
1009 };
1010
imx_dsp_rproc_clk_get(struct imx_dsp_rproc * priv)1011 static int imx_dsp_rproc_clk_get(struct imx_dsp_rproc *priv)
1012 {
1013 struct device *dev = priv->rproc->dev.parent;
1014 struct clk_bulk_data *clks = priv->clks;
1015 int i;
1016
1017 for (i = 0; i < DSP_RPROC_CLK_MAX; i++)
1018 clks[i].id = imx_dsp_clks_names[i];
1019
1020 return devm_clk_bulk_get_optional(dev, DSP_RPROC_CLK_MAX, clks);
1021 }
1022
imx_dsp_rproc_probe(struct platform_device * pdev)1023 static int imx_dsp_rproc_probe(struct platform_device *pdev)
1024 {
1025 const struct imx_dsp_rproc_dcfg *dsp_dcfg;
1026 struct device *dev = &pdev->dev;
1027 struct imx_dsp_rproc *priv;
1028 struct rproc *rproc;
1029 const char *fw_name;
1030 int ret;
1031
1032 dsp_dcfg = of_device_get_match_data(dev);
1033 if (!dsp_dcfg)
1034 return -ENODEV;
1035
1036 ret = rproc_of_parse_firmware(dev, 0, &fw_name);
1037 if (ret) {
1038 dev_err(dev, "failed to parse firmware-name property, ret = %d\n",
1039 ret);
1040 return ret;
1041 }
1042
1043 rproc = devm_rproc_alloc(dev, "imx-dsp-rproc", &imx_dsp_rproc_ops,
1044 fw_name, sizeof(*priv));
1045 if (!rproc)
1046 return -ENOMEM;
1047
1048 priv = rproc->priv;
1049 priv->rproc = rproc;
1050 priv->dsp_dcfg = dsp_dcfg;
1051
1052 if (no_mailboxes)
1053 imx_dsp_rproc_mbox_init = imx_dsp_rproc_mbox_no_alloc;
1054 else
1055 imx_dsp_rproc_mbox_init = imx_dsp_rproc_mbox_alloc;
1056
1057 dev_set_drvdata(dev, rproc);
1058
1059 INIT_WORK(&priv->rproc_work, imx_dsp_rproc_vq_work);
1060
1061 ret = imx_dsp_rproc_detect_mode(priv);
1062 if (ret) {
1063 dev_err(dev, "failed on imx_dsp_rproc_detect_mode\n");
1064 return ret;
1065 }
1066
1067 /* There are multiple power domains required by DSP on some platform */
1068 ret = imx_dsp_attach_pm_domains(priv);
1069 if (ret) {
1070 dev_err(dev, "failed on imx_dsp_attach_pm_domains\n");
1071 return ret;
1072 }
1073 /* Get clocks */
1074 ret = imx_dsp_rproc_clk_get(priv);
1075 if (ret) {
1076 dev_err(dev, "failed on imx_dsp_rproc_clk_get\n");
1077 goto err_detach_domains;
1078 }
1079
1080 init_completion(&priv->pm_comp);
1081 rproc->auto_boot = false;
1082 ret = rproc_add(rproc);
1083 if (ret) {
1084 dev_err(dev, "rproc_add failed\n");
1085 goto err_detach_domains;
1086 }
1087
1088 pm_runtime_enable(dev);
1089
1090 return 0;
1091
1092 err_detach_domains:
1093 dev_pm_domain_detach_list(priv->pd_list);
1094
1095 return ret;
1096 }
1097
imx_dsp_rproc_remove(struct platform_device * pdev)1098 static void imx_dsp_rproc_remove(struct platform_device *pdev)
1099 {
1100 struct rproc *rproc = platform_get_drvdata(pdev);
1101 struct imx_dsp_rproc *priv = rproc->priv;
1102
1103 pm_runtime_disable(&pdev->dev);
1104 rproc_del(rproc);
1105 dev_pm_domain_detach_list(priv->pd_list);
1106 }
1107
1108 /* pm runtime functions */
imx_dsp_runtime_resume(struct device * dev)1109 static int imx_dsp_runtime_resume(struct device *dev)
1110 {
1111 struct rproc *rproc = dev_get_drvdata(dev);
1112 struct imx_dsp_rproc *priv = rproc->priv;
1113 const struct imx_dsp_rproc_dcfg *dsp_dcfg = priv->dsp_dcfg;
1114 int ret;
1115
1116 /*
1117 * There is power domain attached with mailbox, if setup mailbox
1118 * in probe(), then the power of mailbox is always enabled,
1119 * the power can't be saved.
1120 * So move setup of mailbox to runtime resume.
1121 */
1122 ret = imx_dsp_rproc_mbox_init(priv);
1123 if (ret) {
1124 dev_err(dev, "failed on imx_dsp_rproc_mbox_init\n");
1125 return ret;
1126 }
1127
1128 ret = clk_bulk_prepare_enable(DSP_RPROC_CLK_MAX, priv->clks);
1129 if (ret) {
1130 dev_err(dev, "failed on clk_bulk_prepare_enable\n");
1131 return ret;
1132 }
1133
1134 /* Reset DSP if needed */
1135 if (dsp_dcfg->reset)
1136 dsp_dcfg->reset(priv);
1137
1138 return 0;
1139 }
1140
imx_dsp_runtime_suspend(struct device * dev)1141 static int imx_dsp_runtime_suspend(struct device *dev)
1142 {
1143 struct rproc *rproc = dev_get_drvdata(dev);
1144 struct imx_dsp_rproc *priv = rproc->priv;
1145
1146 clk_bulk_disable_unprepare(DSP_RPROC_CLK_MAX, priv->clks);
1147
1148 imx_dsp_rproc_free_mbox(priv);
1149
1150 return 0;
1151 }
1152
imx_dsp_load_firmware(const struct firmware * fw,void * context)1153 static void imx_dsp_load_firmware(const struct firmware *fw, void *context)
1154 {
1155 struct rproc *rproc = context;
1156 int ret;
1157
1158 /*
1159 * Same flow as start procedure.
1160 * Load the ELF segments to memory firstly.
1161 */
1162 ret = rproc_load_segments(rproc, fw);
1163 if (ret)
1164 goto out;
1165
1166 /* Start the remote processor */
1167 ret = rproc->ops->start(rproc);
1168 if (ret)
1169 goto out;
1170
1171 rproc->ops->kick(rproc, 0);
1172
1173 out:
1174 release_firmware(fw);
1175 }
1176
imx_dsp_suspend(struct device * dev)1177 static int imx_dsp_suspend(struct device *dev)
1178 {
1179 struct rproc *rproc = dev_get_drvdata(dev);
1180 struct imx_dsp_rproc *priv = rproc->priv;
1181 __u32 mmsg = RP_MBOX_SUSPEND_SYSTEM;
1182 int ret;
1183
1184 if (rproc->state != RPROC_RUNNING)
1185 goto out;
1186
1187 reinit_completion(&priv->pm_comp);
1188
1189 /* Tell DSP that suspend is happening */
1190 ret = mbox_send_message(priv->tx_ch, (void *)&mmsg);
1191 if (ret < 0) {
1192 dev_err(dev, "PM mbox_send_message failed: %d\n", ret);
1193 return ret;
1194 }
1195
1196 /*
1197 * DSP need to save the context at suspend.
1198 * Here waiting the response for DSP, then power can be disabled.
1199 */
1200 if (!wait_for_completion_timeout(&priv->pm_comp, msecs_to_jiffies(100)))
1201 return -EBUSY;
1202
1203 out:
1204 /*
1205 * The power of DSP is disabled in suspend, so force pm runtime
1206 * to be suspend, then we can reenable the power and clocks at
1207 * resume stage.
1208 */
1209 return pm_runtime_force_suspend(dev);
1210 }
1211
imx_dsp_resume(struct device * dev)1212 static int imx_dsp_resume(struct device *dev)
1213 {
1214 struct rproc *rproc = dev_get_drvdata(dev);
1215 int ret = 0;
1216
1217 ret = pm_runtime_force_resume(dev);
1218 if (ret)
1219 return ret;
1220
1221 if (rproc->state != RPROC_RUNNING)
1222 return 0;
1223
1224 /*
1225 * The power of DSP is disabled at suspend, the memory of dsp
1226 * is reset, the image segments are lost. So need to reload
1227 * firmware and restart the DSP if it is in running state.
1228 */
1229 ret = request_firmware_nowait(THIS_MODULE, FW_ACTION_UEVENT,
1230 rproc->firmware, dev, GFP_KERNEL,
1231 rproc, imx_dsp_load_firmware);
1232 if (ret < 0) {
1233 dev_err(dev, "load firmware failed: %d\n", ret);
1234 goto err;
1235 }
1236
1237 return 0;
1238
1239 err:
1240 pm_runtime_force_suspend(dev);
1241
1242 return ret;
1243 }
1244
1245 static const struct dev_pm_ops imx_dsp_rproc_pm_ops = {
1246 SYSTEM_SLEEP_PM_OPS(imx_dsp_suspend, imx_dsp_resume)
1247 RUNTIME_PM_OPS(imx_dsp_runtime_suspend, imx_dsp_runtime_resume, NULL)
1248 };
1249
1250 static const struct of_device_id imx_dsp_rproc_of_match[] = {
1251 { .compatible = "fsl,imx8qxp-hifi4", .data = &imx_dsp_rproc_cfg_imx8qxp },
1252 { .compatible = "fsl,imx8qm-hifi4", .data = &imx_dsp_rproc_cfg_imx8qm },
1253 { .compatible = "fsl,imx8mp-hifi4", .data = &imx_dsp_rproc_cfg_imx8mp },
1254 { .compatible = "fsl,imx8ulp-hifi4", .data = &imx_dsp_rproc_cfg_imx8ulp },
1255 {},
1256 };
1257 MODULE_DEVICE_TABLE(of, imx_dsp_rproc_of_match);
1258
1259 static struct platform_driver imx_dsp_rproc_driver = {
1260 .probe = imx_dsp_rproc_probe,
1261 .remove_new = imx_dsp_rproc_remove,
1262 .driver = {
1263 .name = "imx-dsp-rproc",
1264 .of_match_table = imx_dsp_rproc_of_match,
1265 .pm = pm_ptr(&imx_dsp_rproc_pm_ops),
1266 },
1267 };
1268 module_platform_driver(imx_dsp_rproc_driver);
1269
1270 MODULE_LICENSE("GPL v2");
1271 MODULE_DESCRIPTION("i.MX HiFi Core Remote Processor Control Driver");
1272 MODULE_AUTHOR("Shengjiu Wang <shengjiu.wang@nxp.com>");
1273