1 /* 2 * PMC-Sierra SPC 8001 SAS/SATA based host adapters driver 3 * 4 * Copyright (c) 2008-2009 USI Co., Ltd. 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions, and the following disclaimer, 12 * without modification. 13 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 14 * substantially similar to the "NO WARRANTY" disclaimer below 15 * ("Disclaimer") and any redistribution must be conditioned upon 16 * including a substantially similar Disclaimer requirement for further 17 * binary redistribution. 18 * 3. Neither the names of the above-listed copyright holders nor the names 19 * of any contributors may be used to endorse or promote products derived 20 * from this software without specific prior written permission. 21 * 22 * Alternatively, this software may be distributed under the terms of the 23 * GNU General Public License ("GPL") version 2 as published by the Free 24 * Software Foundation. 25 * 26 * NO WARRANTY 27 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 28 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 29 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR 30 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 31 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 32 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 33 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 34 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 35 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 36 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 37 * POSSIBILITY OF SUCH DAMAGES. 38 * 39 */ 40 #ifndef _PMC8001_REG_H_ 41 #define _PMC8001_REG_H_ 42 43 #include <linux/types.h> 44 #include <scsi/libsas.h> 45 46 47 /* for Request Opcode of IOMB */ 48 #define OPC_INB_ECHO 1 /* 0x000 */ 49 #define OPC_INB_PHYSTART 4 /* 0x004 */ 50 #define OPC_INB_PHYSTOP 5 /* 0x005 */ 51 #define OPC_INB_SSPINIIOSTART 6 /* 0x006 */ 52 #define OPC_INB_SSPINITMSTART 7 /* 0x007 */ 53 #define OPC_INB_SSPINIEXTIOSTART 8 /* 0x008 */ 54 #define OPC_INB_DEV_HANDLE_ACCEPT 9 /* 0x009 */ 55 #define OPC_INB_SSPTGTIOSTART 10 /* 0x00A */ 56 #define OPC_INB_SSPTGTRSPSTART 11 /* 0x00B */ 57 #define OPC_INB_SSPINIEDCIOSTART 12 /* 0x00C */ 58 #define OPC_INB_SSPINIEXTEDCIOSTART 13 /* 0x00D */ 59 #define OPC_INB_SSPTGTEDCIOSTART 14 /* 0x00E */ 60 #define OPC_INB_SSP_ABORT 15 /* 0x00F */ 61 #define OPC_INB_DEREG_DEV_HANDLE 16 /* 0x010 */ 62 #define OPC_INB_GET_DEV_HANDLE 17 /* 0x011 */ 63 #define OPC_INB_SMP_REQUEST 18 /* 0x012 */ 64 /* SMP_RESPONSE is removed */ 65 #define OPC_INB_SMP_RESPONSE 19 /* 0x013 */ 66 #define OPC_INB_SMP_ABORT 20 /* 0x014 */ 67 #define OPC_INB_REG_DEV 22 /* 0x016 */ 68 #define OPC_INB_SATA_HOST_OPSTART 23 /* 0x017 */ 69 #define OPC_INB_SATA_ABORT 24 /* 0x018 */ 70 #define OPC_INB_LOCAL_PHY_CONTROL 25 /* 0x019 */ 71 #define OPC_INB_GET_DEV_INFO 26 /* 0x01A */ 72 #define OPC_INB_FW_FLASH_UPDATE 32 /* 0x020 */ 73 #define OPC_INB_GPIO 34 /* 0x022 */ 74 #define OPC_INB_SAS_DIAG_MODE_START_END 35 /* 0x023 */ 75 #define OPC_INB_SAS_DIAG_EXECUTE 36 /* 0x024 */ 76 #define OPC_INB_SAS_HW_EVENT_ACK 37 /* 0x025 */ 77 #define OPC_INB_GET_TIME_STAMP 38 /* 0x026 */ 78 #define OPC_INB_PORT_CONTROL 39 /* 0x027 */ 79 #define OPC_INB_GET_NVMD_DATA 40 /* 0x028 */ 80 #define OPC_INB_SET_NVMD_DATA 41 /* 0x029 */ 81 #define OPC_INB_SET_DEVICE_STATE 42 /* 0x02A */ 82 #define OPC_INB_GET_DEVICE_STATE 43 /* 0x02B */ 83 #define OPC_INB_SET_DEV_INFO 44 /* 0x02C */ 84 #define OPC_INB_SAS_RE_INITIALIZE 45 /* 0x02D */ 85 86 /* for Response Opcode of IOMB */ 87 #define OPC_OUB_ECHO 1 /* 0x001 */ 88 #define OPC_OUB_HW_EVENT 4 /* 0x004 */ 89 #define OPC_OUB_SSP_COMP 5 /* 0x005 */ 90 #define OPC_OUB_SMP_COMP 6 /* 0x006 */ 91 #define OPC_OUB_LOCAL_PHY_CNTRL 7 /* 0x007 */ 92 #define OPC_OUB_DEV_REGIST 10 /* 0x00A */ 93 #define OPC_OUB_DEREG_DEV 11 /* 0x00B */ 94 #define OPC_OUB_GET_DEV_HANDLE 12 /* 0x00C */ 95 #define OPC_OUB_SATA_COMP 13 /* 0x00D */ 96 #define OPC_OUB_SATA_EVENT 14 /* 0x00E */ 97 #define OPC_OUB_SSP_EVENT 15 /* 0x00F */ 98 #define OPC_OUB_DEV_HANDLE_ARRIV 16 /* 0x010 */ 99 /* SMP_RECEIVED Notification is removed */ 100 #define OPC_OUB_SMP_RECV_EVENT 17 /* 0x011 */ 101 #define OPC_OUB_SSP_RECV_EVENT 18 /* 0x012 */ 102 #define OPC_OUB_DEV_INFO 19 /* 0x013 */ 103 #define OPC_OUB_FW_FLASH_UPDATE 20 /* 0x014 */ 104 #define OPC_OUB_GPIO_RESPONSE 22 /* 0x016 */ 105 #define OPC_OUB_GPIO_EVENT 23 /* 0x017 */ 106 #define OPC_OUB_GENERAL_EVENT 24 /* 0x018 */ 107 #define OPC_OUB_SSP_ABORT_RSP 26 /* 0x01A */ 108 #define OPC_OUB_SATA_ABORT_RSP 27 /* 0x01B */ 109 #define OPC_OUB_SAS_DIAG_MODE_START_END 28 /* 0x01C */ 110 #define OPC_OUB_SAS_DIAG_EXECUTE 29 /* 0x01D */ 111 #define OPC_OUB_GET_TIME_STAMP 30 /* 0x01E */ 112 #define OPC_OUB_SAS_HW_EVENT_ACK 31 /* 0x01F */ 113 #define OPC_OUB_PORT_CONTROL 32 /* 0x020 */ 114 #define OPC_OUB_SKIP_ENTRY 33 /* 0x021 */ 115 #define OPC_OUB_SMP_ABORT_RSP 34 /* 0x022 */ 116 #define OPC_OUB_GET_NVMD_DATA 35 /* 0x023 */ 117 #define OPC_OUB_SET_NVMD_DATA 36 /* 0x024 */ 118 #define OPC_OUB_DEVICE_HANDLE_REMOVAL 37 /* 0x025 */ 119 #define OPC_OUB_SET_DEVICE_STATE 38 /* 0x026 */ 120 #define OPC_OUB_GET_DEVICE_STATE 39 /* 0x027 */ 121 #define OPC_OUB_SET_DEV_INFO 40 /* 0x028 */ 122 #define OPC_OUB_SAS_RE_INITIALIZE 41 /* 0x029 */ 123 124 /* for phy start*/ 125 #define SPINHOLD_DISABLE (0x00 << 14) 126 #define SPINHOLD_ENABLE (0x01 << 14) 127 #define LINKMODE_SAS (0x01 << 12) 128 #define LINKMODE_DSATA (0x02 << 12) 129 #define LINKMODE_AUTO (0x03 << 12) 130 #define LINKRATE_15 (0x01 << 8) 131 #define LINKRATE_30 (0x02 << 8) 132 #define LINKRATE_60 (0x04 << 8) 133 134 /* for new SPC controllers MEMBASE III is shared between BIOS and DATA */ 135 #define GSM_SM_BASE 0x4F0000 136 struct mpi_msg_hdr{ 137 __le32 header; /* Bits [11:0] - Message operation code */ 138 /* Bits [15:12] - Message Category */ 139 /* Bits [21:16] - Outboundqueue ID for the 140 operation completion message */ 141 /* Bits [23:22] - Reserved */ 142 /* Bits [28:24] - Buffer Count, indicates how 143 many buffer are allocated for the massage */ 144 /* Bits [30:29] - Reserved */ 145 /* Bits [31] - Message Valid bit */ 146 } __attribute__((packed, aligned(4))); 147 148 149 /* 150 * brief the data structure of PHY Start Command 151 * use to describe enable the phy (64 bytes) 152 */ 153 struct phy_start_req { 154 __le32 tag; 155 __le32 ase_sh_lm_slr_phyid; 156 struct sas_identify_frame sas_identify; 157 u32 reserved[5]; 158 } __attribute__((packed, aligned(4))); 159 160 161 /* 162 * brief the data structure of PHY Start Command 163 * use to disable the phy (64 bytes) 164 */ 165 struct phy_stop_req { 166 __le32 tag; 167 __le32 phy_id; 168 u32 reserved[13]; 169 } __attribute__((packed, aligned(4))); 170 171 172 /* set device bits fis - device to host */ 173 struct set_dev_bits_fis { 174 u8 fis_type; /* 0xA1*/ 175 u8 n_i_pmport; 176 /* b7 : n Bit. Notification bit. If set device needs attention. */ 177 /* b6 : i Bit. Interrupt Bit */ 178 /* b5-b4: reserved2 */ 179 /* b3-b0: PM Port */ 180 u8 status; 181 u8 error; 182 u32 _r_a; 183 } __attribute__ ((packed)); 184 /* PIO setup FIS - device to host */ 185 struct pio_setup_fis { 186 u8 fis_type; /* 0x5f */ 187 u8 i_d_pmPort; 188 /* b7 : reserved */ 189 /* b6 : i bit. Interrupt bit */ 190 /* b5 : d bit. data transfer direction. set to 1 for device to host 191 xfer */ 192 /* b4 : reserved */ 193 /* b3-b0: PM Port */ 194 u8 status; 195 u8 error; 196 u8 lbal; 197 u8 lbam; 198 u8 lbah; 199 u8 device; 200 u8 lbal_exp; 201 u8 lbam_exp; 202 u8 lbah_exp; 203 u8 _r_a; 204 u8 sector_count; 205 u8 sector_count_exp; 206 u8 _r_b; 207 u8 e_status; 208 u8 _r_c[2]; 209 u8 transfer_count; 210 } __attribute__ ((packed)); 211 212 /* 213 * brief the data structure of SATA Completion Response 214 * use to describe the sata task response (64 bytes) 215 */ 216 struct sata_completion_resp { 217 __le32 tag; 218 __le32 status; 219 __le32 param; 220 u32 sata_resp[12]; 221 } __attribute__((packed, aligned(4))); 222 223 224 /* 225 * brief the data structure of SAS HW Event Notification 226 * use to alert the host about the hardware event(64 bytes) 227 */ 228 struct hw_event_resp { 229 __le32 lr_evt_status_phyid_portid; 230 __le32 evt_param; 231 __le32 npip_portstate; 232 struct sas_identify_frame sas_identify; 233 struct dev_to_host_fis sata_fis; 234 } __attribute__((packed, aligned(4))); 235 236 237 /* 238 * brief the data structure of REGISTER DEVICE Command 239 * use to describe MPI REGISTER DEVICE Command (64 bytes) 240 */ 241 242 struct reg_dev_req { 243 __le32 tag; 244 __le32 phyid_portid; 245 __le32 dtype_dlr_retry; 246 __le32 firstburstsize_ITNexustimeout; 247 u8 sas_addr[SAS_ADDR_SIZE]; 248 __le32 upper_device_id; 249 u32 reserved[8]; 250 } __attribute__((packed, aligned(4))); 251 252 253 /* 254 * brief the data structure of DEREGISTER DEVICE Command 255 * use to request spc to remove all internal resources associated 256 * with the device id (64 bytes) 257 */ 258 259 struct dereg_dev_req { 260 __le32 tag; 261 __le32 device_id; 262 u32 reserved[13]; 263 } __attribute__((packed, aligned(4))); 264 265 266 /* 267 * brief the data structure of DEVICE_REGISTRATION Response 268 * use to notify the completion of the device registration (64 bytes) 269 */ 270 271 struct dev_reg_resp { 272 __le32 tag; 273 __le32 status; 274 __le32 device_id; 275 u32 reserved[12]; 276 } __attribute__((packed, aligned(4))); 277 278 279 /* 280 * brief the data structure of Local PHY Control Command 281 * use to issue PHY CONTROL to local phy (64 bytes) 282 */ 283 struct local_phy_ctl_req { 284 __le32 tag; 285 __le32 phyop_phyid; 286 u32 reserved1[13]; 287 } __attribute__((packed, aligned(4))); 288 289 290 /** 291 * brief the data structure of Local Phy Control Response 292 * use to describe MPI Local Phy Control Response (64 bytes) 293 */ 294 struct local_phy_ctl_resp { 295 __le32 tag; 296 __le32 phyop_phyid; 297 __le32 status; 298 u32 reserved[12]; 299 } __attribute__((packed, aligned(4))); 300 301 302 #define OP_BITS 0x0000FF00 303 #define ID_BITS 0x000000FF 304 305 /* 306 * brief the data structure of PORT Control Command 307 * use to control port properties (64 bytes) 308 */ 309 310 struct port_ctl_req { 311 __le32 tag; 312 __le32 portop_portid; 313 __le32 param0; 314 __le32 param1; 315 u32 reserved1[11]; 316 } __attribute__((packed, aligned(4))); 317 318 319 /* 320 * brief the data structure of HW Event Ack Command 321 * use to acknowledge receive HW event (64 bytes) 322 */ 323 324 struct hw_event_ack_req { 325 __le32 tag; 326 __le32 sea_phyid_portid; 327 __le32 param0; 328 __le32 param1; 329 u32 reserved1[11]; 330 } __attribute__((packed, aligned(4))); 331 332 333 /* 334 * brief the data structure of SSP Completion Response 335 * use to indicate a SSP Completion (n bytes) 336 */ 337 struct ssp_completion_resp { 338 __le32 tag; 339 __le32 status; 340 __le32 param; 341 __le32 ssptag_rescv_rescpad; 342 struct ssp_response_iu ssp_resp_iu; 343 __le32 residual_count; 344 } __attribute__((packed, aligned(4))); 345 346 347 #define SSP_RESCV_BIT 0x00010000 348 349 /* 350 * brief the data structure of SATA EVNET esponse 351 * use to indicate a SATA Completion (64 bytes) 352 */ 353 354 struct sata_event_resp { 355 __le32 tag; 356 __le32 event; 357 __le32 port_id; 358 __le32 device_id; 359 u32 reserved[11]; 360 } __attribute__((packed, aligned(4))); 361 362 /* 363 * brief the data structure of SSP EVNET esponse 364 * use to indicate a SSP Completion (64 bytes) 365 */ 366 367 struct ssp_event_resp { 368 __le32 tag; 369 __le32 event; 370 __le32 port_id; 371 __le32 device_id; 372 u32 reserved[11]; 373 } __attribute__((packed, aligned(4))); 374 375 /** 376 * brief the data structure of General Event Notification Response 377 * use to describe MPI General Event Notification Response (64 bytes) 378 */ 379 struct general_event_resp { 380 __le32 status; 381 __le32 inb_IOMB_payload[14]; 382 } __attribute__((packed, aligned(4))); 383 384 385 #define GENERAL_EVENT_PAYLOAD 14 386 #define OPCODE_BITS 0x00000fff 387 388 /* 389 * brief the data structure of SMP Request Command 390 * use to describe MPI SMP REQUEST Command (64 bytes) 391 */ 392 struct smp_req { 393 __le32 tag; 394 __le32 device_id; 395 __le32 len_ip_ir; 396 /* Bits [0] - Indirect response */ 397 /* Bits [1] - Indirect Payload */ 398 /* Bits [15:2] - Reserved */ 399 /* Bits [23:16] - direct payload Len */ 400 /* Bits [31:24] - Reserved */ 401 u8 smp_req16[16]; 402 union { 403 u8 smp_req[32]; 404 struct { 405 __le64 long_req_addr;/* sg dma address, LE */ 406 __le32 long_req_size;/* LE */ 407 u32 _r_a; 408 __le64 long_resp_addr;/* sg dma address, LE */ 409 __le32 long_resp_size;/* LE */ 410 u32 _r_b; 411 } long_smp_req;/* sequencer extension */ 412 }; 413 } __attribute__((packed, aligned(4))); 414 /* 415 * brief the data structure of SMP Completion Response 416 * use to describe MPI SMP Completion Response (64 bytes) 417 */ 418 struct smp_completion_resp { 419 __le32 tag; 420 __le32 status; 421 __le32 param; 422 __le32 _r_a[12]; 423 } __attribute__((packed, aligned(4))); 424 425 /* 426 *brief the data structure of SSP SMP SATA Abort Command 427 * use to describe MPI SSP SMP & SATA Abort Command (64 bytes) 428 */ 429 struct task_abort_req { 430 __le32 tag; 431 __le32 device_id; 432 __le32 tag_to_abort; 433 __le32 abort_all; 434 u32 reserved[11]; 435 } __attribute__((packed, aligned(4))); 436 437 /** 438 * brief the data structure of SSP SATA SMP Abort Response 439 * use to describe SSP SMP & SATA Abort Response ( 64 bytes) 440 */ 441 struct task_abort_resp { 442 __le32 tag; 443 __le32 status; 444 __le32 scp; 445 u32 reserved[12]; 446 } __attribute__((packed, aligned(4))); 447 448 449 /** 450 * brief the data structure of SAS Diagnostic Start/End Command 451 * use to describe MPI SAS Diagnostic Start/End Command (64 bytes) 452 */ 453 struct sas_diag_start_end_req { 454 __le32 tag; 455 __le32 operation_phyid; 456 u32 reserved[13]; 457 } __attribute__((packed, aligned(4))); 458 459 460 /** 461 * brief the data structure of SAS Diagnostic Execute Command 462 * use to describe MPI SAS Diagnostic Execute Command (64 bytes) 463 */ 464 struct sas_diag_execute_req{ 465 __le32 tag; 466 __le32 cmdtype_cmddesc_phyid; 467 __le32 pat1_pat2; 468 __le32 threshold; 469 __le32 codepat_errmsk; 470 __le32 pmon; 471 __le32 pERF1CTL; 472 u32 reserved[8]; 473 } __attribute__((packed, aligned(4))); 474 475 476 #define SAS_DIAG_PARAM_BYTES 24 477 478 /* 479 * brief the data structure of Set Device State Command 480 * use to describe MPI Set Device State Command (64 bytes) 481 */ 482 struct set_dev_state_req { 483 __le32 tag; 484 __le32 device_id; 485 __le32 nds; 486 u32 reserved[12]; 487 } __attribute__((packed, aligned(4))); 488 489 /* 490 * brief the data structure of sas_re_initialization 491 */ 492 struct sas_re_initialization_req { 493 494 __le32 tag; 495 __le32 SSAHOLT;/* bit29-set max port; 496 ** bit28-set open reject cmd retries. 497 ** bit27-set open reject data retries. 498 ** bit26-set open reject option, remap:1 or not:0. 499 ** bit25-set sata head of line time out. 500 */ 501 __le32 reserved_maxPorts; 502 __le32 open_reject_cmdretries_data_retries;/* cmd retries: 31-bit16; 503 * data retries: bit15-bit0. 504 */ 505 __le32 sata_hol_tmo; 506 u32 reserved1[10]; 507 } __attribute__((packed, aligned(4))); 508 509 /* 510 * brief the data structure of SATA Start Command 511 * use to describe MPI SATA IO Start Command (64 bytes) 512 */ 513 514 struct sata_start_req { 515 __le32 tag; 516 __le32 device_id; 517 __le32 data_len; 518 __le32 retfis_ncqtag_atap_dir_m; 519 struct host_to_dev_fis sata_fis; 520 u32 reserved1; 521 u32 reserved2; 522 u32 addr_low; 523 u32 addr_high; 524 __le32 len; 525 __le32 esgl; 526 } __attribute__((packed, aligned(4))); 527 528 /** 529 * brief the data structure of SSP INI TM Start Command 530 * use to describe MPI SSP INI TM Start Command (64 bytes) 531 */ 532 struct ssp_ini_tm_start_req { 533 __le32 tag; 534 __le32 device_id; 535 __le32 relate_tag; 536 __le32 tmf; 537 u8 lun[8]; 538 __le32 ds_ads_m; 539 u32 reserved[8]; 540 } __attribute__((packed, aligned(4))); 541 542 543 struct ssp_info_unit { 544 u8 lun[8];/* SCSI Logical Unit Number */ 545 u8 reserved1;/* reserved */ 546 u8 efb_prio_attr; 547 /* B7 : enabledFirstBurst */ 548 /* B6-3 : taskPriority */ 549 /* B2-0 : taskAttribute */ 550 u8 reserved2; /* reserved */ 551 u8 additional_cdb_len; 552 /* B7-2 : additional_cdb_len */ 553 /* B1-0 : reserved */ 554 u8 cdb[16];/* The SCSI CDB up to 16 bytes length */ 555 } __attribute__((packed, aligned(4))); 556 557 558 /** 559 * brief the data structure of SSP INI IO Start Command 560 * use to describe MPI SSP INI IO Start Command (64 bytes) 561 */ 562 struct ssp_ini_io_start_req { 563 __le32 tag; 564 __le32 device_id; 565 __le32 data_len; 566 __le32 dir_m_tlr; 567 struct ssp_info_unit ssp_iu; 568 __le32 addr_low; 569 __le32 addr_high; 570 __le32 len; 571 __le32 esgl; 572 } __attribute__((packed, aligned(4))); 573 574 575 /** 576 * brief the data structure of Firmware download 577 * use to describe MPI FW DOWNLOAD Command (64 bytes) 578 */ 579 struct fw_flash_Update_req { 580 __le32 tag; 581 __le32 cur_image_offset; 582 __le32 cur_image_len; 583 __le32 total_image_len; 584 u32 reserved0[7]; 585 __le32 sgl_addr_lo; 586 __le32 sgl_addr_hi; 587 __le32 len; 588 __le32 ext_reserved; 589 } __attribute__((packed, aligned(4))); 590 591 592 #define FWFLASH_IOMB_RESERVED_LEN 0x07 593 /** 594 * brief the data structure of FW_FLASH_UPDATE Response 595 * use to describe MPI FW_FLASH_UPDATE Response (64 bytes) 596 * 597 */ 598 struct fw_flash_Update_resp { 599 __le32 tag; 600 __le32 status; 601 u32 reserved[13]; 602 } __attribute__((packed, aligned(4))); 603 604 605 /** 606 * brief the data structure of Get NVM Data Command 607 * use to get data from NVM in HBA(64 bytes) 608 */ 609 struct get_nvm_data_req { 610 __le32 tag; 611 __le32 len_ir_vpdd; 612 __le32 vpd_offset; 613 u32 reserved[8]; 614 __le32 resp_addr_lo; 615 __le32 resp_addr_hi; 616 __le32 resp_len; 617 u32 reserved1; 618 } __attribute__((packed, aligned(4))); 619 620 621 struct set_nvm_data_req { 622 __le32 tag; 623 __le32 len_ir_vpdd; 624 __le32 vpd_offset; 625 __le32 reserved[8]; 626 __le32 resp_addr_lo; 627 __le32 resp_addr_hi; 628 __le32 resp_len; 629 u32 reserved1; 630 } __attribute__((packed, aligned(4))); 631 632 633 #define TWI_DEVICE 0x0 634 #define C_SEEPROM 0x1 635 #define VPD_FLASH 0x4 636 #define AAP1_RDUMP 0x5 637 #define IOP_RDUMP 0x6 638 #define EXPAN_ROM 0x7 639 640 #define IPMode 0x80000000 641 #define NVMD_TYPE 0x0000000F 642 #define NVMD_STAT 0x0000FFFF 643 #define NVMD_LEN 0xFF000000 644 /** 645 * brief the data structure of Get NVMD Data Response 646 * use to describe MPI Get NVMD Data Response (64 bytes) 647 */ 648 struct get_nvm_data_resp { 649 __le32 tag; 650 __le32 ir_tda_bn_dps_das_nvm; 651 __le32 dlen_status; 652 __le32 nvm_data[12]; 653 } __attribute__((packed, aligned(4))); 654 655 656 /** 657 * brief the data structure of SAS Diagnostic Start/End Response 658 * use to describe MPI SAS Diagnostic Start/End Response (64 bytes) 659 * 660 */ 661 struct sas_diag_start_end_resp { 662 __le32 tag; 663 __le32 status; 664 u32 reserved[13]; 665 } __attribute__((packed, aligned(4))); 666 667 668 /** 669 * brief the data structure of SAS Diagnostic Execute Response 670 * use to describe MPI SAS Diagnostic Execute Response (64 bytes) 671 * 672 */ 673 struct sas_diag_execute_resp { 674 __le32 tag; 675 __le32 cmdtype_cmddesc_phyid; 676 __le32 Status; 677 __le32 ReportData; 678 u32 reserved[11]; 679 } __attribute__((packed, aligned(4))); 680 681 682 /** 683 * brief the data structure of Set Device State Response 684 * use to describe MPI Set Device State Response (64 bytes) 685 * 686 */ 687 struct set_dev_state_resp { 688 __le32 tag; 689 __le32 status; 690 __le32 device_id; 691 __le32 pds_nds; 692 u32 reserved[11]; 693 } __attribute__((packed, aligned(4))); 694 695 696 #define NDS_BITS 0x0F 697 #define PDS_BITS 0xF0 698 699 /* 700 * HW Events type 701 */ 702 703 #define HW_EVENT_RESET_START 0x01 704 #define HW_EVENT_CHIP_RESET_COMPLETE 0x02 705 #define HW_EVENT_PHY_STOP_STATUS 0x03 706 #define HW_EVENT_SAS_PHY_UP 0x04 707 #define HW_EVENT_SATA_PHY_UP 0x05 708 #define HW_EVENT_SATA_SPINUP_HOLD 0x06 709 #define HW_EVENT_PHY_DOWN 0x07 710 #define HW_EVENT_PORT_INVALID 0x08 711 #define HW_EVENT_BROADCAST_CHANGE 0x09 712 #define HW_EVENT_PHY_ERROR 0x0A 713 #define HW_EVENT_BROADCAST_SES 0x0B 714 #define HW_EVENT_INBOUND_CRC_ERROR 0x0C 715 #define HW_EVENT_HARD_RESET_RECEIVED 0x0D 716 #define HW_EVENT_MALFUNCTION 0x0E 717 #define HW_EVENT_ID_FRAME_TIMEOUT 0x0F 718 #define HW_EVENT_BROADCAST_EXP 0x10 719 #define HW_EVENT_PHY_START_STATUS 0x11 720 #define HW_EVENT_LINK_ERR_INVALID_DWORD 0x12 721 #define HW_EVENT_LINK_ERR_DISPARITY_ERROR 0x13 722 #define HW_EVENT_LINK_ERR_CODE_VIOLATION 0x14 723 #define HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH 0x15 724 #define HW_EVENT_LINK_ERR_PHY_RESET_FAILED 0x16 725 #define HW_EVENT_PORT_RECOVERY_TIMER_TMO 0x17 726 #define HW_EVENT_PORT_RECOVER 0x18 727 #define HW_EVENT_PORT_RESET_TIMER_TMO 0x19 728 #define HW_EVENT_PORT_RESET_COMPLETE 0x20 729 #define EVENT_BROADCAST_ASYNCH_EVENT 0x21 730 731 /* port state */ 732 #define PORT_NOT_ESTABLISHED 0x00 733 #define PORT_VALID 0x01 734 #define PORT_LOSTCOMM 0x02 735 #define PORT_IN_RESET 0x04 736 #define PORT_INVALID 0x08 737 738 /* 739 * SSP/SMP/SATA IO Completion Status values 740 */ 741 742 #define IO_SUCCESS 0x00 743 #define IO_ABORTED 0x01 744 #define IO_OVERFLOW 0x02 745 #define IO_UNDERFLOW 0x03 746 #define IO_FAILED 0x04 747 #define IO_ABORT_RESET 0x05 748 #define IO_NOT_VALID 0x06 749 #define IO_NO_DEVICE 0x07 750 #define IO_ILLEGAL_PARAMETER 0x08 751 #define IO_LINK_FAILURE 0x09 752 #define IO_PROG_ERROR 0x0A 753 #define IO_EDC_IN_ERROR 0x0B 754 #define IO_EDC_OUT_ERROR 0x0C 755 #define IO_ERROR_HW_TIMEOUT 0x0D 756 #define IO_XFER_ERROR_BREAK 0x0E 757 #define IO_XFER_ERROR_PHY_NOT_READY 0x0F 758 #define IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED 0x10 759 #define IO_OPEN_CNX_ERROR_ZONE_VIOLATION 0x11 760 #define IO_OPEN_CNX_ERROR_BREAK 0x12 761 #define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS 0x13 762 #define IO_OPEN_CNX_ERROR_BAD_DESTINATION 0x14 763 #define IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED 0x15 764 #define IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY 0x16 765 #define IO_OPEN_CNX_ERROR_WRONG_DESTINATION 0x17 766 #define IO_OPEN_CNX_ERROR_UNKNOWN_ERROR 0x18 767 #define IO_XFER_ERROR_NAK_RECEIVED 0x19 768 #define IO_XFER_ERROR_ACK_NAK_TIMEOUT 0x1A 769 #define IO_XFER_ERROR_PEER_ABORTED 0x1B 770 #define IO_XFER_ERROR_RX_FRAME 0x1C 771 #define IO_XFER_ERROR_DMA 0x1D 772 #define IO_XFER_ERROR_CREDIT_TIMEOUT 0x1E 773 #define IO_XFER_ERROR_SATA_LINK_TIMEOUT 0x1F 774 #define IO_XFER_ERROR_SATA 0x20 775 #define IO_XFER_ERROR_ABORTED_DUE_TO_SRST 0x22 776 #define IO_XFER_ERROR_REJECTED_NCQ_MODE 0x21 777 #define IO_XFER_ERROR_ABORTED_NCQ_MODE 0x23 778 #define IO_XFER_OPEN_RETRY_TIMEOUT 0x24 779 #define IO_XFER_SMP_RESP_CONNECTION_ERROR 0x25 780 #define IO_XFER_ERROR_UNEXPECTED_PHASE 0x26 781 #define IO_XFER_ERROR_XFER_RDY_OVERRUN 0x27 782 #define IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED 0x28 783 784 #define IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT 0x30 785 #define IO_XFER_ERROR_CMD_ISSUE_BREAK_BEFORE_ACK_NAK 0x31 786 #define IO_XFER_ERROR_CMD_ISSUE_PHY_DOWN_BEFORE_ACK_NAK 0x32 787 788 #define IO_XFER_ERROR_OFFSET_MISMATCH 0x34 789 #define IO_XFER_ERROR_XFER_ZERO_DATA_LEN 0x35 790 #define IO_XFER_CMD_FRAME_ISSUED 0x36 791 #define IO_ERROR_INTERNAL_SMP_RESOURCE 0x37 792 #define IO_PORT_IN_RESET 0x38 793 #define IO_DS_NON_OPERATIONAL 0x39 794 #define IO_DS_IN_RECOVERY 0x3A 795 #define IO_TM_TAG_NOT_FOUND 0x3B 796 #define IO_XFER_PIO_SETUP_ERROR 0x3C 797 #define IO_SSP_EXT_IU_ZERO_LEN_ERROR 0x3D 798 #define IO_DS_IN_ERROR 0x3E 799 #define IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY 0x3F 800 #define IO_ABORT_IN_PROGRESS 0x40 801 #define IO_ABORT_DELAYED 0x41 802 #define IO_INVALID_LENGTH 0x42 803 #define IO_FATAL_ERROR 0x51 804 805 /* WARNING: This error code must always be the last number. 806 * If you add error code, modify this code also 807 * It is used as an index 808 */ 809 #define IO_ERROR_UNKNOWN_GENERIC 0x43 810 811 /* MSGU CONFIGURATION TABLE*/ 812 813 #define SPC_MSGU_CFG_TABLE_UPDATE 0x01/* Inbound doorbell bit0 */ 814 #define SPC_MSGU_CFG_TABLE_RESET 0x02/* Inbound doorbell bit1 */ 815 #define SPC_MSGU_CFG_TABLE_FREEZE 0x04/* Inbound doorbell bit2 */ 816 #define SPC_MSGU_CFG_TABLE_UNFREEZE 0x08/* Inbound doorbell bit4 */ 817 #define MSGU_IBDB_SET 0x04 818 #define MSGU_HOST_INT_STATUS 0x08 819 #define MSGU_HOST_INT_MASK 0x0C 820 #define MSGU_IOPIB_INT_STATUS 0x18 821 #define MSGU_IOPIB_INT_MASK 0x1C 822 #define MSGU_IBDB_CLEAR 0x20/* RevB - Host not use */ 823 #define MSGU_MSGU_CONTROL 0x24 824 #define MSGU_ODR 0x3C/* RevB */ 825 #define MSGU_ODCR 0x40/* RevB */ 826 #define MSGU_SCRATCH_PAD_0 0x44 827 #define MSGU_SCRATCH_PAD_1 0x48 828 #define MSGU_SCRATCH_PAD_2 0x4C 829 #define MSGU_SCRATCH_PAD_3 0x50 830 #define MSGU_HOST_SCRATCH_PAD_0 0x54 831 #define MSGU_HOST_SCRATCH_PAD_1 0x58 832 #define MSGU_HOST_SCRATCH_PAD_2 0x5C 833 #define MSGU_HOST_SCRATCH_PAD_3 0x60 834 #define MSGU_HOST_SCRATCH_PAD_4 0x64 835 #define MSGU_HOST_SCRATCH_PAD_5 0x68 836 #define MSGU_HOST_SCRATCH_PAD_6 0x6C 837 #define MSGU_HOST_SCRATCH_PAD_7 0x70 838 #define MSGU_ODMR 0x74/* RevB */ 839 840 /* bit definition for ODMR register */ 841 #define ODMR_MASK_ALL 0xFFFFFFFF/* mask all 842 interrupt vector */ 843 #define ODMR_CLEAR_ALL 0/* clear all 844 interrupt vector */ 845 /* bit definition for ODCR register */ 846 #define ODCR_CLEAR_ALL 0xFFFFFFFF /* mask all 847 interrupt vector*/ 848 /* MSIX Interupts */ 849 #define MSIX_TABLE_OFFSET 0x2000 850 #define MSIX_TABLE_ELEMENT_SIZE 0x10 851 #define MSIX_INTERRUPT_CONTROL_OFFSET 0xC 852 #define MSIX_TABLE_BASE (MSIX_TABLE_OFFSET + MSIX_INTERRUPT_CONTROL_OFFSET) 853 #define MSIX_INTERRUPT_DISABLE 0x1 854 #define MSIX_INTERRUPT_ENABLE 0x0 855 856 857 /* state definition for Scratch Pad1 register */ 858 #define SCRATCH_PAD1_POR 0x00 /* power on reset state */ 859 #define SCRATCH_PAD1_SFR 0x01 /* soft reset state */ 860 #define SCRATCH_PAD1_ERR 0x02 /* error state */ 861 #define SCRATCH_PAD1_RDY 0x03 /* ready state */ 862 #define SCRATCH_PAD1_RST 0x04 /* soft reset toggle flag */ 863 #define SCRATCH_PAD1_AAP1RDY_RST 0x08 /* AAP1 ready for soft reset */ 864 #define SCRATCH_PAD1_STATE_MASK 0xFFFFFFF0 /* ScratchPad1 865 Mask, bit1-0 State, bit2 Soft Reset, bit3 FW RDY for Soft Reset */ 866 #define SCRATCH_PAD1_RESERVED 0x000003F8 /* Scratch Pad1 867 Reserved bit 3 to 9 */ 868 869 /* state definition for Scratch Pad2 register */ 870 #define SCRATCH_PAD2_POR 0x00 /* power on state */ 871 #define SCRATCH_PAD2_SFR 0x01 /* soft reset state */ 872 #define SCRATCH_PAD2_ERR 0x02 /* error state */ 873 #define SCRATCH_PAD2_RDY 0x03 /* ready state */ 874 #define SCRATCH_PAD2_FWRDY_RST 0x04 /* FW ready for soft reset flag*/ 875 #define SCRATCH_PAD2_IOPRDY_RST 0x08 /* IOP ready for soft reset */ 876 #define SCRATCH_PAD2_STATE_MASK 0xFFFFFFF4 /* ScratchPad 2 877 Mask, bit1-0 State */ 878 #define SCRATCH_PAD2_RESERVED 0x000003FC /* Scratch Pad1 879 Reserved bit 2 to 9 */ 880 881 #define SCRATCH_PAD_ERROR_MASK 0xFFFFFC00 /* Error mask bits */ 882 #define SCRATCH_PAD_STATE_MASK 0x00000003 /* State Mask bits */ 883 884 /* main configuration offset - byte offset */ 885 #define MAIN_SIGNATURE_OFFSET 0x00/* DWORD 0x00 */ 886 #define MAIN_INTERFACE_REVISION 0x04/* DWORD 0x01 */ 887 #define MAIN_FW_REVISION 0x08/* DWORD 0x02 */ 888 #define MAIN_MAX_OUTSTANDING_IO_OFFSET 0x0C/* DWORD 0x03 */ 889 #define MAIN_MAX_SGL_OFFSET 0x10/* DWORD 0x04 */ 890 #define MAIN_CNTRL_CAP_OFFSET 0x14/* DWORD 0x05 */ 891 #define MAIN_GST_OFFSET 0x18/* DWORD 0x06 */ 892 #define MAIN_IBQ_OFFSET 0x1C/* DWORD 0x07 */ 893 #define MAIN_OBQ_OFFSET 0x20/* DWORD 0x08 */ 894 #define MAIN_IQNPPD_HPPD_OFFSET 0x24/* DWORD 0x09 */ 895 #define MAIN_OB_HW_EVENT_PID03_OFFSET 0x28/* DWORD 0x0A */ 896 #define MAIN_OB_HW_EVENT_PID47_OFFSET 0x2C/* DWORD 0x0B */ 897 #define MAIN_OB_NCQ_EVENT_PID03_OFFSET 0x30/* DWORD 0x0C */ 898 #define MAIN_OB_NCQ_EVENT_PID47_OFFSET 0x34/* DWORD 0x0D */ 899 #define MAIN_TITNX_EVENT_PID03_OFFSET 0x38/* DWORD 0x0E */ 900 #define MAIN_TITNX_EVENT_PID47_OFFSET 0x3C/* DWORD 0x0F */ 901 #define MAIN_OB_SSP_EVENT_PID03_OFFSET 0x40/* DWORD 0x10 */ 902 #define MAIN_OB_SSP_EVENT_PID47_OFFSET 0x44/* DWORD 0x11 */ 903 #define MAIN_OB_SMP_EVENT_PID03_OFFSET 0x48/* DWORD 0x12 */ 904 #define MAIN_OB_SMP_EVENT_PID47_OFFSET 0x4C/* DWORD 0x13 */ 905 #define MAIN_EVENT_LOG_ADDR_HI 0x50/* DWORD 0x14 */ 906 #define MAIN_EVENT_LOG_ADDR_LO 0x54/* DWORD 0x15 */ 907 #define MAIN_EVENT_LOG_BUFF_SIZE 0x58/* DWORD 0x16 */ 908 #define MAIN_EVENT_LOG_OPTION 0x5C/* DWORD 0x17 */ 909 #define MAIN_IOP_EVENT_LOG_ADDR_HI 0x60/* DWORD 0x18 */ 910 #define MAIN_IOP_EVENT_LOG_ADDR_LO 0x64/* DWORD 0x19 */ 911 #define MAIN_IOP_EVENT_LOG_BUFF_SIZE 0x68/* DWORD 0x1A */ 912 #define MAIN_IOP_EVENT_LOG_OPTION 0x6C/* DWORD 0x1B */ 913 #define MAIN_FATAL_ERROR_INTERRUPT 0x70/* DWORD 0x1C */ 914 #define MAIN_FATAL_ERROR_RDUMP0_OFFSET 0x74/* DWORD 0x1D */ 915 #define MAIN_FATAL_ERROR_RDUMP0_LENGTH 0x78/* DWORD 0x1E */ 916 #define MAIN_FATAL_ERROR_RDUMP1_OFFSET 0x7C/* DWORD 0x1F */ 917 #define MAIN_FATAL_ERROR_RDUMP1_LENGTH 0x80/* DWORD 0x20 */ 918 #define MAIN_HDA_FLAGS_OFFSET 0x84/* DWORD 0x21 */ 919 #define MAIN_ANALOG_SETUP_OFFSET 0x88/* DWORD 0x22 */ 920 921 /* Gereral Status Table offset - byte offset */ 922 #define GST_GSTLEN_MPIS_OFFSET 0x00 923 #define GST_IQ_FREEZE_STATE0_OFFSET 0x04 924 #define GST_IQ_FREEZE_STATE1_OFFSET 0x08 925 #define GST_MSGUTCNT_OFFSET 0x0C 926 #define GST_IOPTCNT_OFFSET 0x10 927 #define GST_PHYSTATE_OFFSET 0x18 928 #define GST_PHYSTATE0_OFFSET 0x18 929 #define GST_PHYSTATE1_OFFSET 0x1C 930 #define GST_PHYSTATE2_OFFSET 0x20 931 #define GST_PHYSTATE3_OFFSET 0x24 932 #define GST_PHYSTATE4_OFFSET 0x28 933 #define GST_PHYSTATE5_OFFSET 0x2C 934 #define GST_PHYSTATE6_OFFSET 0x30 935 #define GST_PHYSTATE7_OFFSET 0x34 936 #define GST_RERRINFO_OFFSET 0x44 937 938 /* General Status Table - MPI state */ 939 #define GST_MPI_STATE_UNINIT 0x00 940 #define GST_MPI_STATE_INIT 0x01 941 #define GST_MPI_STATE_TERMINATION 0x02 942 #define GST_MPI_STATE_ERROR 0x03 943 #define GST_MPI_STATE_MASK 0x07 944 945 #define MBIC_NMI_ENABLE_VPE0_IOP 0x000418 946 #define MBIC_NMI_ENABLE_VPE0_AAP1 0x000418 947 /* PCIE registers - BAR2(0x18), BAR1(win) 0x010000 */ 948 #define PCIE_EVENT_INTERRUPT_ENABLE 0x003040 949 #define PCIE_EVENT_INTERRUPT 0x003044 950 #define PCIE_ERROR_INTERRUPT_ENABLE 0x003048 951 #define PCIE_ERROR_INTERRUPT 0x00304C 952 /* signature definition for host scratch pad0 register */ 953 #define SPC_SOFT_RESET_SIGNATURE 0x252acbcd 954 /* Signature for Soft Reset */ 955 956 /* SPC Reset register - BAR4(0x20), BAR2(win) (need dynamic mapping) */ 957 #define SPC_REG_RESET 0x000000/* reset register */ 958 959 /* bit difination for SPC_RESET register */ 960 #define SPC_REG_RESET_OSSP 0x00000001 961 #define SPC_REG_RESET_RAAE 0x00000002 962 #define SPC_REG_RESET_PCS_SPBC 0x00000004 963 #define SPC_REG_RESET_PCS_IOP_SS 0x00000008 964 #define SPC_REG_RESET_PCS_AAP1_SS 0x00000010 965 #define SPC_REG_RESET_PCS_AAP2_SS 0x00000020 966 #define SPC_REG_RESET_PCS_LM 0x00000040 967 #define SPC_REG_RESET_PCS 0x00000080 968 #define SPC_REG_RESET_GSM 0x00000100 969 #define SPC_REG_RESET_DDR2 0x00010000 970 #define SPC_REG_RESET_BDMA_CORE 0x00020000 971 #define SPC_REG_RESET_BDMA_SXCBI 0x00040000 972 #define SPC_REG_RESET_PCIE_AL_SXCBI 0x00080000 973 #define SPC_REG_RESET_PCIE_PWR 0x00100000 974 #define SPC_REG_RESET_PCIE_SFT 0x00200000 975 #define SPC_REG_RESET_PCS_SXCBI 0x00400000 976 #define SPC_REG_RESET_LMS_SXCBI 0x00800000 977 #define SPC_REG_RESET_PMIC_SXCBI 0x01000000 978 #define SPC_REG_RESET_PMIC_CORE 0x02000000 979 #define SPC_REG_RESET_PCIE_PC_SXCBI 0x04000000 980 #define SPC_REG_RESET_DEVICE 0x80000000 981 982 /* registers for BAR Shifting - BAR2(0x18), BAR1(win) */ 983 #define SPC_IBW_AXI_TRANSLATION_LOW 0x003258 984 985 #define MBIC_AAP1_ADDR_BASE 0x060000 986 #define MBIC_IOP_ADDR_BASE 0x070000 987 #define GSM_ADDR_BASE 0x0700000 988 /* Dynamic map through Bar4 - 0x00700000 */ 989 #define GSM_CONFIG_RESET 0x00000000 990 #define RAM_ECC_DB_ERR 0x00000018 991 #define GSM_READ_ADDR_PARITY_INDIC 0x00000058 992 #define GSM_WRITE_ADDR_PARITY_INDIC 0x00000060 993 #define GSM_WRITE_DATA_PARITY_INDIC 0x00000068 994 #define GSM_READ_ADDR_PARITY_CHECK 0x00000038 995 #define GSM_WRITE_ADDR_PARITY_CHECK 0x00000040 996 #define GSM_WRITE_DATA_PARITY_CHECK 0x00000048 997 998 #define RB6_ACCESS_REG 0x6A0000 999 #define HDAC_EXEC_CMD 0x0002 1000 #define HDA_C_PA 0xcb 1001 #define HDA_SEQ_ID_BITS 0x00ff0000 1002 #define HDA_GSM_OFFSET_BITS 0x00FFFFFF 1003 #define MBIC_AAP1_ADDR_BASE 0x060000 1004 #define MBIC_IOP_ADDR_BASE 0x070000 1005 #define GSM_ADDR_BASE 0x0700000 1006 #define SPC_TOP_LEVEL_ADDR_BASE 0x000000 1007 #define GSM_CONFIG_RESET_VALUE 0x00003b00 1008 #define GPIO_ADDR_BASE 0x00090000 1009 #define GPIO_GPIO_0_0UTPUT_CTL_OFFSET 0x0000010c 1010 1011 /* RB6 offset */ 1012 #define SPC_RB6_OFFSET 0x80C0 1013 /* Magic number of soft reset for RB6 */ 1014 #define RB6_MAGIC_NUMBER_RST 0x1234 1015 1016 /* Device Register status */ 1017 #define DEVREG_SUCCESS 0x00 1018 #define DEVREG_FAILURE_OUT_OF_RESOURCE 0x01 1019 #define DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED 0x02 1020 #define DEVREG_FAILURE_INVALID_PHY_ID 0x03 1021 #define DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED 0x04 1022 #define DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE 0x05 1023 #define DEVREG_FAILURE_PORT_NOT_VALID_STATE 0x06 1024 #define DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID 0x07 1025 1026 #define GSM_BASE 0x4F0000 1027 #define SHIFT_REG_64K_MASK 0xffff0000 1028 #define SHIFT_REG_BIT_SHIFT 8 1029 #endif 1030 1031