xref: /linux/drivers/phy/ti/Kconfig (revision 9a87ffc99ec8eb8d35eed7c4f816d75f5cc9662e)
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# Phy drivers for TI platforms
4#
5config PHY_DA8XX_USB
6	tristate "TI DA8xx USB PHY Driver"
7	depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST
8	select GENERIC_PHY
9	select MFD_SYSCON
10	help
11	  Enable this to support the USB PHY on DA8xx SoCs.
12
13	  This driver controls both the USB 1.1 PHY and the USB 2.0 PHY.
14
15config PHY_DM816X_USB
16	tristate "TI dm816x USB PHY driver"
17	depends on ARCH_OMAP2PLUS || COMPILE_TEST
18	depends on USB_SUPPORT
19	select GENERIC_PHY
20	select USB_PHY
21	help
22	  Enable this for dm816x USB to work.
23
24config PHY_AM654_SERDES
25	tristate "TI AM654 SERDES support"
26	depends on OF && (ARCH_K3 || COMPILE_TEST)
27	depends on COMMON_CLK
28	select GENERIC_PHY
29	select MULTIPLEXER
30	select REGMAP_MMIO
31	select MUX_MMIO
32	help
33	  This option enables support for TI AM654 SerDes PHY used for
34	  PCIe.
35
36config PHY_J721E_WIZ
37	tristate "TI J721E WIZ (SERDES Wrapper) support"
38	depends on OF && (ARCH_K3 || COMPILE_TEST)
39	depends on HAS_IOMEM && OF_ADDRESS
40	depends on COMMON_CLK
41	select GENERIC_PHY
42	select MULTIPLEXER
43	select REGMAP_MMIO
44	select MUX_MMIO
45	help
46	  This option enables support for WIZ module present in TI's J721E
47	  SoC. WIZ is a serdes wrapper used to configure some of the input
48	  signals to the SERDES (Sierra/Torrent). This driver configures
49	  three clock selects (pll0, pll1, dig) and resets for each of the
50	  lanes.
51
52config OMAP_CONTROL_PHY
53	tristate "OMAP CONTROL PHY Driver"
54	depends on ARCH_OMAP2PLUS || COMPILE_TEST
55	help
56	  Enable this to add support for the PHY part present in the control
57	  module. This driver has API to power on the USB2 PHY and to write to
58	  the mailbox. The mailbox is present only in omap4 and the register to
59	  power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
60	  additional register to power on USB3 PHY/SATA PHY/PCIE PHY
61	  (PIPE3 PHY).
62
63config OMAP_USB2
64	tristate "OMAP USB2 PHY Driver"
65	depends on ARCH_OMAP2PLUS || ARCH_K3
66	depends on USB_SUPPORT
67	select GENERIC_PHY
68	select USB_PHY
69	select OMAP_CONTROL_PHY if ARCH_OMAP2PLUS || COMPILE_TEST
70	help
71	  Enable this to support the transceiver that is part of SOC. This
72	  driver takes care of all the PHY functionality apart from comparator.
73	  The USB OTG controller communicates with the comparator using this
74	  driver.
75
76config TI_PIPE3
77	tristate "TI PIPE3 PHY Driver"
78	depends on ARCH_OMAP2PLUS || COMPILE_TEST
79	select GENERIC_PHY
80	select OMAP_CONTROL_PHY
81	help
82	  Enable this to support the PIPE3 PHY that is part of TI SOCs. This
83	  driver takes care of all the PHY functionality apart from comparator.
84	  This driver interacts with the "OMAP Control PHY Driver" to power
85	  on/off the PHY.
86
87config PHY_TUSB1210
88	tristate "TI TUSB1210 ULPI PHY module"
89	depends on USB_ULPI_BUS
90	select GENERIC_PHY
91	help
92	  Support for TI TUSB1210 USB ULPI PHY.
93
94config TWL4030_USB
95	tristate "TWL4030 USB Transceiver Driver"
96	depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
97	depends on USB_SUPPORT
98	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't 'y'
99	select GENERIC_PHY
100	select USB_PHY
101	help
102	  Enable this to support the USB OTG transceiver on TWL4030
103	  family chips (including the TWL5030 and TPS659x0 devices).
104	  This transceiver supports high and full speed devices plus,
105	  in host mode, low speed.
106
107config PHY_TI_GMII_SEL
108	tristate
109	select GENERIC_PHY
110	select REGMAP
111	help
112	  This driver supports configuring of the TI CPSW Port mode depending on
113	  the Ethernet PHY connected to the CPSW Port.
114