Lines Matching +full:reboot +full:- +full:mode

8 stmsboot \- administration program for the Solaris I/O multipathing feature
12 \fB/usr/sbin/stmsboot\fR [[\fB-d\fR | \fB-e\fR [\fB-D\fR (fp | mpt) ]]
13       | \fB-u\fR | \fB-L\fR | \fB-l\fR \fIcontroller_number\fR]
25 of multipath-capable devices with Solaris I/O multipathing. Solaris I/O
26 multipathing-enabled devices are enumerated under \fBscsi_vhci\fR(4D),
27 providing multipathing capabilities. Solaris I/O multipathing-disabled devices
31 In the \fB/dev\fR and \fB/devices\fR trees, Solaris I/O multipathing-enabled
37 disabling Solaris I/O multipathing. One reboot is required for changes to take
46 \fB\fB-e\fR [ \fB-D\fR \fBfp | mpt\fR ]\fR
50 Enables Solaris I/O multipathing on all supported multipath-capable controller
51 ports. Multipath-capable ports include fibre channel (\fBfp\fR(4D)) controller
53 are prompted to reboot. During the reboot, \fBvfstab\fR and the dump
55 either \fB-D\fR \fBmpt\fR or \fB-D\fR \fBfp\fR limits the enabling operation to
62 \fB\fB-d\fR [ \fB-D\fR \fBfp | mpt\fR ]\fR
66 Disables Solaris I/O multipathing on all supported multipath-capable controller
67 ports. Multipath-capable ports include fibre channel (\fBfp\fR(4D)) controller
69 are prompted to reboot. During the reboot, \fBvfstab\fR and the dump
71 either \fB-D\fR \fBmpt\fR or \fB-D\fR \fBfp\fR limits the disabling operation
78 \fB\fB-u\fR\fR
84 on specific multipath-capable controller ports. This option prompts you to
85 reboot. During the reboot, \fBvfstab\fR and the dump configuration will be
92 \fB\fB-L\fR\fR
96 Display the device name changes from non-Solaris I/O multipathing device names
97 to Solaris I/O multipathing device names for multipath-enabled controller
105 \fB\fB-l\fR \fIcontroller_number\fR\fR
109 Display the device name changes from non-Solaris I/O multipathing device names
125 The \fB-L\fR and \fB-l\fR options display the mapping between multipathed and
126 non-multipathed device names. These options function only after changes to the
128 the reboot after invoking \fBstmsboot\fR \fB-e\fR.
138 To enable Solaris I/O multipathing for all multipath-capable controllers, run:
143 # \fBstmsboot -e\fR
150 To enable Solaris I/O multipathing on multipath-capable \fBmpt\fR(4D)
156 # \fBstmsboot -D mpt -e\fR
163 To enable Solaris I/O Multipathing on multipath-capable fibre channel
169 # \fBstmsboot -D fp -e\fR
178 To disable Solaris I/O multipathing on all multipath-capable controllers,
184 # \fBstmsboot -d\fR
191 To disable Solaris I/O multipathing on multipath-capable \fBmpt\fR(4D)
197 # \fBstmsboot -D mpt -d\fR
204 To disable Solaris I/O multipathing on multipath-capable fibre channel
210 # \fBstmsboot -D fp -d\fR
227 # \fBstmsboot -u\fR
283 multipathing control. Non-supported devices remain unchanged.
286 For Solaris releases prior to the current release, the \fB-e\fR and \fB-d\fR
287 options replace \fBmpxio-disable\fR property entries with a global
288 \fBmpxio-disable\fR entry in \fBfp.conf\fR.
298 of the subsystem must be set to \fBmpxio\fR mode. The preferred sequence is to
299 change the subsystem's \fBmp_support\fR to \fBmpxio\fR mode, then run
300 \fBstmsboot\fR \fB-e\fR. If Solaris I/O multipathing is already enabled but the
301 subsystem's \fBmp_support\fR is not in \fBmpxio\fR mode, then change the
302 \fBmp_support\fR to \fBmpxio\fR mode and run \fBstmsboot\fR \fB-u\fR.
313 (\fB-e\fR, \fB-d\fR, and \fB-u\fR) is to change the device name of a storage
325 If possible, invoke \fBstmsboot\fR \fB-e\fR before installing Sun Cluster
339 # \fBstmsboot -e\fR
346 \&...and allow the system to reboot.
353 # \fB/usr/cluster/bin/scdidadm -C\fR
358 # \fB/usr/cluster/bin/scdidadm -r\fR
375 Reboot the system.
379 To disable the Solaris multipathing feature, use \fBstmsboot\fR \fB-d\fR
380 (instead of \fBstmsboot\fR \fB-e\fR), then follow the procedure above.
384 \fB-L\fR. To view \fBdid\fR device name mappings, run
385 \fB/usr/cluster/bin/scdidadm\fR \fB-L\fR.
388 With active-passive storage arrays, it is possible that while your host is
400 Solaris I/O multipathing is always enabled for supported fibre channel-attached
402 performed on a per-port basis. See \fBfp\fR(4D).
405 Executing \fBdevfsadm\fR \fB-C\fR removes obsolete device entries that
406 \fBstmsboot\fR relies on. This will prevent correct operation of the \fB-d\fR
407 option for boot devices (regardless of platform type) and the \fB-L\fR option.