Lines Matching +full:em +full:- +full:uart
31 .Nd Point to Point Protocol (a.k.a. user-ppp)
99 .Bl -tag -width XXX -offset XXX
141 exits with a non-zero result.
161 .Dq force-scripts
176 As pipes are not bi-directional, ppp will redirect all writes to descriptor
186 .Dq force-scripts
195 This is a no-op, and gives the same behaviour as if none of the above
213 .Bl -diag
231 .It Supports on-demand dialup capability.
243 mode (direct-dial mode) also automatically dials and establishes the
248 This mode is useful for full-time connections where we worry less
255 will never voluntarily quit from dedicated mode - you must send it the
267 .Pq Lk https://winprotocoldocs-bhdugrdyduf5h2e4.b02.azurefd.net/MS-CBCP/%5bMS-CBCP%5d.pdf .
275 UDP port numbers are NAT'd for outgoing packets and de-NAT'd for
285 .It Supports server-side PPP connections.
310 distributed database along with various per-user framed connection
343 .Em host : Ns Em port Ns
377 .It "Supports IETF draft Predictor-1 (rfc 1978) and DEFLATE (rfc 1979) compression."
379 supports not only VJ-compression but also Predictor-1 and DEFLATE compression.
380 Normally, a modem has built-in compression (e.g., v42.bis) and the system
386 Unlike VJ-compression, Predictor-1 and DEFLATE compression pre-compresses
395 .It Supports Multi-link PPP (rfc 1990)
400 .It Supports MPPE (draft-ietf-pppext-mppe)
444 .Bl -bullet
470 .Bd -literal -offset indent
485 .Bd -literal -offset indent
530 .Bd -literal -offset indent
545 .Bd -literal -offset indent
553 to certain PPP-capable terminal servers), this may result in
556 as it is waiting for the CTS (clear to send) signal - which will never
563 description below too - you will probably need to
573 link-layer protocols (that is what
589 .Bd -literal -offset indent
594 .Bd -literal -offset indent
615 .Bd -literal -offset indent
630 .Bd -literal -offset indent
648 peer wants to use PAP or CHAP authentication instead of using Unix-style
652 .Bd -literal -offset indent
664 .Bd -literal -offset indent
683 .Bd -literal -offset indent
699 .Bd -literal -offset indent
725 .Bd -literal -offset indent
736 .Bd -literal -offset indent
766 .Bl -bullet
775 It must have one argument - the file to {include}.
803 .Bd -literal -offset indent
818 .Dq ppp-in
836 .Bd -literal -offset indent
866 .Bd -literal -offset indent
910 it was necessary to re-add routes such as the default route in the
927 non-interactively (such as from a
943 exits immediately with a non-zero exit code.
965 .Bd -literal -offset indent
966 # ppp -auto pmdemand
983 .Bd -literal -offset indent
1016 .Oo - Ns Ar max Ns Oc Oc Ns
1020 .Bl -tag -width attempts -compact
1065 .Bd -literal -offset indent
1077 .Bd -literal -offset indent
1078 set redial 10+10-5.3 20
1108 .Bd -literal -offset indent
1114 to re-establish the connection
1120 .Bd -literal -offset indent
1153 .Bd -literal -offset indent
1176 .Bl -enum
1181 .Bl -bullet -compact
1204 .Dl # kill -HUP 1
1208 .Bd -literal -offset indent
1230 .Bd -literal -offset indent
1232 exec /usr/sbin/ppp -direct incoming
1243 client-side
1258 .Bd -literal
1281 .Bl -enum
1288 .Bd -literal
1316 .Bd -literal
1355 .Ar hisaddr Op Ar label Op Ar callback-number
1397 .Ar callback-number
1404 .Ar callback-number
1420 .Dl set device ui-gate:6669/tcp
1432 connection on the receiving machine (ui-gate).
1437 .Dl ppp-in 6669/tcp # Incoming PPP connections over TCP
1445 .Dl ppp-in stream tcp nowait root /usr/sbin/ppp ppp -direct ppp-in
1454 .Dq ppp-in .
1457 on ui-gate (the receiver) should contain the following:
1458 .Bd -literal -offset indent
1459 ppp-in:
1467 .Bd -literal -offset indent
1468 ppp-in:
1482 .Bd -literal -offset indent
1488 .Bd -literal -offset indent
1503 .Bd -literal -offset indent
1504 ui-gate:
1506 set device ui-gate:ppp-in/tcp
1515 .Bd -literal -offset indent
1516 ui-gate:
1523 .Bd -literal -offset indent
1528 We are assigning the address of 10.0.4.1 to ui-gate, and the address
1532 .Dl awfulhak # ppp -background ui-gate
1536 "route" on ui-gate to the 10.0.1.0/24 network.
1537 The networks are effectively bridged - the underlying TCP
1546 "guaranteed delivery" mechanisms in place - the underlying TCP
1549 link - probably TCP again.
1572 .Bd -literal -offset indent
1573 ui-gate:
1575 set device ui-gate:ppp-in/tcp
1576 add ui-gate x.x.x.x
1583 .Dq ui-gate
1594 .Bd -literal -offset indent
1623 host, and incoming packets are de-NAT'd so that they are routed
1674 .Bl -bullet
1680 .Ar rule-no
1694 .Bl -enum
1704 .Ar Rule-no
1711 .Ar rule-no ,
1778 meaning less-than, equal and greater-than respectively.
1818 .Ar filter-decapsulation
1822 .Dq set filter Ar name No -1
1834 .Bd -literal -offset indent
1842 .Bd -literal -offset indent
1859 Another trigger packet will cause it to attempt to re-establish the link.
1860 .Sh PREDICTOR-1 and DEFLATE COMPRESSION
1918 .Bd -ragged -offset indent
1960 .Bd -literal -offset indent
1966 .Bl -bullet -compact
1979 This is all fine when each side has a pre-determined IP address, however
1993 .Bl -bullet -compact
2018 .Bl -enum
2028 .Bd -ragged -offset indent
2033 Numbers after the first in a pipe-separated list are only used if the
2039 .Bd -literal -offset indent
2067 .Bd -literal -offset indent
2083 .Bd -literal -offset indent
2085 ATZ OK-ATZ-OK ATDT\\\\T TIMEOUT 60 CONNECT"
2089 .Bl -bullet
2114 .Bd -literal -offset indent
2116 set login "TIMEOUT 15 login:-\\\\r-login: awfulhak \e
2121 .Bl -bullet
2165 .Bd -literal -offset indent
2176 .Xr uart 4
2193 .Bl -bullet
2219 .Bd -literal -offset indent
2225 .Bd -literal -offset indent
2251 .Bd -literal -offset indent
2264 .Bd -literal -offset indent
2294 .Bl -tag -width XXXXXXXXX -offset XXX -compact
2383 (i.e., only the un-maskable warning, error and alert output).
2390 .Sq -
2393 .Bd -literal -offset indent
2398 PPP ON awfulhak> set log +tcp/ip -warning
2416 .Bl -tag -width "USR2"
2434 to re-open any existing server socket, dropping all existing diagnostic
2443 can still be used to re-open the socket.
2445 .Sh MULTI-LINK PPP
2449 .Em MULTI-LINK PPP
2461 confusing lock-ups may result.
2473 Multi-link capabilities are enabled using the
2476 Once multi-link is enabled,
2478 will attempt to negotiate a multi-link connection with the peer.
2490 .Bl -enum
2522 Some commands can still be used without specifying a link - resulting
2528 will show CCP configuration and statistics at the multi-link level, and
2535 .Bd -literal -offset indent
2542 OK-AT-OK \\\\dATDT\\\\T TIMEOUT 45 CONNECT"
2549 clone 1,2,3 # Create 3 new links - duplicates of the default
2558 .Bd -literal -offset indent
2563 .Bd -literal -offset indent
2572 .Bd -literal -offset indent
2588 .Em MULTI-LINK
2608 negotiates multi-link mode, it will pass its open link to any
2623 .Bl -tag -width 2n
2642 .Bl -tag -width 2n
2647 field of 0xff (the All-Stations address) and a control field of
2661 The peer uses a one-way hash function to encrypt the
2685 implementations use "MS-CHAP" rather than MD5 when encrypting the
2687 MS-CHAP is a combination of MD4 and DES.
2691 to MS-CHAP authentication requests, but will never request them.
2703 - a
2718 .Dq PPP Magna-link Variable Resource Compression
2841 40-, 56- and 128-bits.
2849 combination of MD4, SHA-1 and DES to encrypt the challenge rather than using the
2861 CHAP type 0x80 for LANMan is also supported - see
2930 sequence numbers when negotiating multi-link mode.
2931 This is only applicable if our MRRU is set (thus enabling multi-link).
2939 .Bl -tag -width 2n
2967 .It filter-decapsulation
2992 .It force-scripts
3003 exchanges low-level LCP, CCP and IPCP configuration traffic, the
3015 .It iface-alias
3039 .Sq iface-alias .
3052 .It keep-session
3056 runs as a Multi-link server, a different
3107 .It NAS-IP-Address
3112 .Dq NAS-IP-Address
3117 .Dq NAS-IP-Address
3119 .Dq NAS-Identifier
3125 .Dq NAS-IP-Address
3128 .Dq NAS-IP-Address
3130 .Dq NAS-Identifier
3135 .Dq disable NAS-IP-Address .
3136 .It NAS-Identifier
3141 .Dq NAS-Identifier
3146 .Dq NAS-IP-Address
3148 .Dq NAS-Identifier
3213 Each time these variables change, this list is re-applied to the routing table.
3215 Disabling this option will prevent the re-application of sticky routes,
3335 It is possible to allow user-level access,
3350 .Bl -tag -width 2n
3404 When running in multi-link mode, a section can be loaded if it allows
3419 .Bl -tag -width 2n
3461 .No - Ns Ar targetPort
3464 .No - Ns Ar aliasPort
3468 .No - Ns Ar remotePort
3583 When enabled, UDP packets use endpoint-independent mapping (EIM) from RFC 4787
3595 When disabled, UDP packets use endpoint-dependent mapping (EDM) ("symmetric"
3601 by port forwarding on the NAT, or tunnelling through an in-between server.
3621 .Bl -tag -width COMPILATIONDATE
3711 Normally, this variable is assigned only in -direct mode.
3780 it will re-enter the STOPPED state, waiting for the peer to initiate
3800 all non-direct entries in the routing table for the current interface,
3866 .Bl -tag -width 2n
3889 is used - in which case the previous interface address entry is overwritten
3943 .It iface help Op Ar sub-command
3945 .Ar sub-command ,
3948 sub-commands and a brief synopsis for each.
3950 .Ar sub-command ,
3951 only the synopsis for the given sub-command is shown.
3959 This is only applicable after multiple links have been created in Multi-link
4012 .Ar demand-dial
4013 links - these will come up based on the
4038 It is probably not good practice to re-open the PPP state machines
4077 It is only really useful in multi-link mode.
4108 .Bl -tag -width readonly
4109 .It Em readonly
4126 .It Em reload
4132 .It Em restore
4141 .It Em rewrite
4153 .It Em writable
4193 .Bl -tag -width 2n
4194 .It set accmap Ar hex-value
4251 .Bl -bullet
4262 .Bl -bullet
4290 .Ar min-percent max-percent period
4292 These settings apply only in multi-link mode and default to zero, zero and
4295 .Ar demand-dial
4302 .Ar demand-dial
4304 .Ar max-percent
4309 .Ar min-percent
4313 .Ar demand-dial
4320 .Ar demand-dial
4357 will accept any of the given protocols - but the client
4367 .Bl -tag -width Ds
4427 is disabled - ie, configuring CBCP in the
4459 .Bl -tag -width XXX -offset XXX
4467 NULL-modem cables), logs the fact and stops checking
4551 packets in multi-link mode), then stops reading the network interface
4564 .It set deflate Ar out-winsize Op Ar in-winsize
4568 .Ar out-winsize
4570 .Ar in-winsize
4576 .Ar in-winsize
4692 .It set dial Ar chat-script
4705 .Bl -tag -width 2n
4747 .Bd -literal -offset indent
4771 .Bd -literal -offset indent
4772 set login "TIMEOUT 5 \\"\\" \\"\\" login:--login: ppp \e
4773 word: ppp \\"!sh \\\\-c \\\\\\"echo \\\\-n label: >&2\\\\\\"\\" \e
4780 .Bd -literal -offset indent
4785 Chat: Expecting: login:--login:
4791 Chat: Expecting: !sh \\-c "echo \\-n label: >&2"
4792 Chat: Exec: sh -c "echo -n label: >&2"
4793 Chat: Wait for (5): !sh \\-c "echo \\-n label: >&2" --> label:
4810 an expect-send-expect sequence.
4844 .Bl -tag -width indent
4895 .It set filter dial|alive|in|out Ar rule-no Xo
4896 .No permit|deny|clear\&| Ns Ar rule-no
4913 filter specifies packets that keep the connection alive - resetting the
4934 .Ar rule-no
4960 .It set hangup Ar chat-script
4997 .Bd -ragged -offset indent
5004 .Dl set ifaddr 10.0.0.1 10.0.1.2-10.0.1.10,10.0.1.20
5015 to re-establish a link using the same IP number as was previously
5136 .Op +|- Ns
5141 .It set login Ar chat-script
5143 .Ar chat-script
5144 compliments the dial-script.
5148 .It set logout Ar chat-script
5174 This is normally only useful in multi-link mode,
5175 but may also be used in uni-link mode.
5185 .Dq enable iface-alias
5217 encryption dictionary is re-initialised with every packet according to
5220 the encryption dictionary is re-initialised every 256 packets or after
5225 Setting this option enables Multi-link PPP negotiations, also known as
5226 Multi-link Protocol or MP.
5228 If no argument is given, multi-link mode is disabled.
5371 .It set radius Op Ar config-file
5373 .Ar config-file
5394 .Bl -tag -width XXX -offset XXX
5452 .Dq 1.2.3.4/24 0.0.0.0 1 2 -1 3 400
5534 vendor specific attribute is supplied and if MS-CHAPv2 authentication is
5581 to a non-zero
5592 NAS-Port-Id.
5596 .Bl -tag -width Ds
5610 failure), a connection will be re-established after the given
5612 The line will be re-connected at most
5630 .Oo - Ns Ar max Ns Oc Oc Ns
5707 to attempt to re-open the port.
5812 .Oo Op +|- Ns
5909 .Bl -tag -width 2n
5952 Show Multi-link information.
5976 .Bl -bullet
5991 .Bl -bullet -compact
5993 https://docs.freebsd.org/en/books/handbook/ppp-and-slip/
6007 .Bl -tag -width 2n
6048 .It Pa /var/run/ppp-authname-class-value
6049 In multi-link mode, local domain sockets are created using the peer
6101 .An Toshiharu OHNO Aq Mt tony-o@iij.ad.jp ,
6116 in early 1998 when multi-link ppp support was added.