Lines Matching +full:device +full:- +full:width

39 .Op Fl D Ar device
44 .Op Fl D Ar device
51 .Op Fl D Ar device
56 .Op Fl D Ar device
61 .Op Fl D Ar device
71 .Op Fl D Ar device
76 .Op Fl D Ar device
81 .Op Fl D Ar device
88 .Op Fl D Ar device
95 .Op Fl D Ar device
100 .Op Fl D Ar device
105 .Op Fl D Ar device
110 .Op Fl D Ar device
115 .Op Fl D Ar device
120 .Op Fl D Ar device
125 .Op Fl D Ar device
130 .Op Fl D Ar device
135 .Op Fl D Ar device
140 .Op Fl D Ar device
145 .Op Fl D Ar device
150 .Op Fl D Ar device
155 .Op Fl D Ar device
160 .Op Fl D Ar device
165 .Op Fl D Ar device
170 .Op Fl D Ar device
179 .Op Fl D Ar device
184 .Op Fl D Ar device
189 .Op Fl D Ar device
194 .Op Fl D Ar device
199 .Op Fl D Ar device
204 .Op Fl D Ar device
209 .Op Fl D Ar device
214 .Op Fl D Ar device
219 .Op Fl D Ar device
224 .Op Fl D Ar device
229 .Op Fl D Ar device
234 .Op Fl D Ar device
239 .Op Fl D Ar device
244 .Op Fl D Ar device
249 .Op Fl D Ar device
254 .Op Fl D Ar device
270 .Bl -tag -width indent
271 .It Fl D Ar device
272 .Ar device
273 specifies the device node of the controller to use.
275 will be added to the device node if needed.
276 If no device node is specified,
277 then device will be made of the type and device.
294 .Bl -tag -width indent
296 Print numeric device IDs as drive identifier.
300 to print both, numeric device IDs and enclosure:slot information.
309 a drive may be identified by its device ID.
310 The device ID for configured drives can be found in
332 device,
347 The fifth group of commands are used to manage controller-wide operations.
350 .Bl -tag -width indent
382 .Bl -tag -width indent
386 Periodic progress updates for long-running operations such as background
421 the controller for each low-level request.
433 .Bl -tag -width indent
462 .Bl -tag -width indent
482 Present the drive to the host operating system as a disk SYSPD block device in
496 Abort an in-progress rebuild operation on
507 .Bl -tag -width indent
525 .Bl -tag -width indent
534 .It Cm write-back
535 Use write-back policy for cached writes.
536 .It Cm write-through
537 Use write-through policy for cached writes.
538 .It Cm read-ahead Ar value
547 .It Cm bad-bbu-write-cache Ar value
558 .It Cm write-cache Ar value
585 .Bl -tag -width indent
599 .Bl -tag -width indent
671 .Bl -tag -width indent
677 .Bl -tag -width indent
692 argument specifies a non-negative, relative start time for the next patrol read.
745 .Bl -tag -width indent
746 .It Cm learn-delay
749 .It Cm autolearn-mode
760 .It Cm bbu-mode
770 With an integer argument (0-100), set that value as the new rebuild rate for volumes.
780 .Dl Nm Cm cache mfid0 write-back
795 Add drive with the device ID of 4 as a global hot spare:
803 Reconfigure a disk as a SYSPD block device with no RAID