Lines Matching +full:pll +full:- +full:mode
1 /*-
2 * SPDX-License-Identifier: BSD-2-Clause
50 #define MCS7840_DEV_REG_PINPONGHIGH 0x02 /* High bits of ping-pong
52 #define MCS7840_DEV_REG_PINPONGLOW 0x03 /* Low bits of ping-pong
67 #define MCS7840_DEV_REG_PLL_DIV_M 0x0e /* Pre-diviedr for PLL, R/W */
69 #define MCS7840_DEV_REG_PLL_DIV_N 0x10 /* Loop divider for PLL, R/W */
70 #define MCS7840_DEV_REG_CLOCK_MUX 0x12 /* PLL input clock & Interrupt
78 /* DCRx_2-DCRx_4 Registers goes here (see below, they are documented) */
109 #define MCS7840_DEV_REG_BI_FIFO_STAT1 0x32 /* Bulk-In FIFO Stat for Port
112 #define MCS7840_DEV_REG_BO_FIFO_STAT1 0x33 /* Bulk-out FIFO Stat for Port
115 #define MCS7840_DEV_REG_BI_FIFO_STAT2 0x34 /* Bulk-In FIFO Stat for Port
118 #define MCS7840_DEV_REG_BO_FIFO_STAT2 0x35 /* Bulk-out FIFO Stat for Port
121 #define MCS7840_DEV_REG_BI_FIFO_STAT3 0x36 /* Bulk-In FIFO Stat for Port
124 #define MCS7840_DEV_REG_BO_FIFO_STAT3 0x37 /* Bulk-out FIFO Stat for Port
127 #define MCS7840_DEV_REG_BI_FIFO_STAT4 0x38 /* Bulk-In FIFO Stat for Port
130 #define MCS7840_DEV_REG_BO_FIFO_STAT4 0x39 /* Bulk-out FIFO Stat for Port
144 * value for Bulk-Out for Port
147 * value for Bulk-Out and
150 * value for Bulk-Out for Port
153 * value for Bulk-Out and
156 * value for Bulk-Out for Port
159 * value for Bulk-Out and
162 * value for Bulk-Out for Port
165 * value for Bulk-Out and
169 #define MCS7840_DEV_SPx_LOOP_PIPES 0x01 /* Loop Bulk-Out FIFO to the
170 * Bulk-In FIFO, default = 0 */
174 #define MCS7840_DEV_SPx_RESET_OUT_FIFO 0x04 /* Reset Bulk-Out FIFO */
175 #define MCS7840_DEV_SPx_RESET_IN_FIFO 0x08 /* Reset Bulk-In FIFO */
215 * works for IrDA mode
219 * RS-232/RS-485 mode,
223 * works for IrDA mode
230 * for Bulk-In FIFOs are swapped. One of buffers is used
240 * THIS ONE IS UNDOCUMENTED IN FULL DATASHEET, but e-mail from tech support
243 * authors as "number of port" indicator, grounded (0) for two-port
244 * devices and pulled-up to 1 for 4-port devices.
252 * Constants for PLL dividers
253 * Ouptut frequency of PLL is:
255 * Default PLL input frequency Fin is 12Mhz (on-chip).
273 #define MCS7840_DEV_CLOCK_MUX_INPUTMASK 0x03 /* Mask to extract PLL clock
275 #define MCS7840_DEV_CLOCK_MUX_IN12MHZ 0x00 /* 12Mhz PLL input, default */
276 #define MCS7840_DEV_CLOCK_MUX_INEXTRN 0x01 /* External (device-depended)
277 * PLL input */
280 #define MCS7840_DEV_CLOCK_MUX_PLLHIGH 0x04 /* 0 = PLL Output is
281 * 20MHz-100MHz (default), 1 =
282 * 100MHz-300MHz range */
315 #define MCS7840_DEV_CLOCK_SELECT_PLL 0x04 /* PLL output (see for M and N
318 * (device-dependend) */
322 /* Bits for MODE register */
329 #define MCS7840_DEV_MODE_PLLBYPASS 0x08 /* 1: PLL output is bypassed,
331 #define MCS7840_DEV_MODE_PORBYPASS 0x10 /* 1: Power-On Reset is
338 #define MCS7840_DEV_MODE_IRDA 0x80 /* IrDA mode is activated
375 #define MCS7840_DEV_ZERO_PERIODx_DEF 20 /* Number of Bulk-in requests
376 * befor sending zero-sized
381 * zero-sized replies for port
384 * zero-sized replies for port
387 * zero-sized replies for port
390 * zero-sized replies for port
430 #define MCS7840_DEV_DCR0_GPIO_MODE_MASK 0x0c /* GPIO Mode bits, WORKS
432 #define MCS7840_DEV_DCR0_GPIO_MODE_IN 0x00 /* GPIO Mode - Input
435 #define MCS7840_DEV_DCR0_GPIO_MODE_OUT 0x08 /* GPIO Mode - Input
444 #define MCS7840_DEV_DCR0_IRDA 0x40 /* IrDA mode */
475 #define MCS7840_DEV_DCR1_PLLPWRDOWN_DISABLE 0x20 /* Disable PLL power
486 * Wakeup will work only if DCR0_IRDA = 0 (RS-xxx mode) and
510 * Thesse can be calculated as "1 << portnumber" for Bulk-out and
511 * "1 << (portnumber+1)" for Bulk-in
527 #define MCS7840_UART_REG_IER 0x01 /* Interrupt enable register -
529 #define MCS7840_UART_REG_FCR 0x02 /* FIFO Control register -
581 #define MCS7840_UART_LCR_STOPB2 0x04 /* 1.5-2 stop bits depends on
585 #define MCS7840_UART_LCR_PARITYON 0x08 /* Parity ON/OFF - ON */
613 * mode */
615 * in 550 (FIFO) mode */
617 * in 550 (FIFO) mode */
619 * 550 (FIFO) mode */
636 #define MCS7840_UART_SCRATCHPAD_RS232 0x00 /* RS-485 disabled */
637 #define MCS7840_UART_SCRATCHPAD_RS485_DTRRX 0x80 /* RS-485 mode, DTR High
639 #define MCS7840_UART_SCRATCHPAD_RS485_DTRTX 0xc0 /* RS-485 mode, DTR High