Lines Matching +full:i2c +full:- +full:arb
17 * are provided to you under the BSD-type license terms provided
22 * - Redistributions of source code must retain the above copyright
24 * - Redistributions in binary form must reproduce the above
28 * - Neither the name of Marvell nor the names of its contributors
48 /*-
49 * SPDX-License-Identifier: BSD-4-Clause AND BSD-3-Clause
65 * 4. Neither the name of the author nor the names of any co-contributors
82 /*-
110 * D-Link PCI vendor ID
154 * D-Link gigabit ethernet device ID
262 #define PCI_Y2_PIG_ENA BIT_31 /* Enable Plug-in-Go (YUKON-2) */
263 #define PCI_Y2_DLL_DIS BIT_30 /* Disable PCI DLL (YUKON-2) */
264 #define PCI_Y2_PHY2_COMA BIT_29 /* Set PHY 2 to Coma Mode (YUKON-2) */
265 #define PCI_Y2_PHY1_COMA BIT_28 /* Set PHY 1 to Coma Mode (YUKON-2) */
266 #define PCI_Y2_PHY2_POWD BIT_27 /* Set PHY 2 to Power Down (YUKON-2) */
267 #define PCI_Y2_PHY1_POWD BIT_26 /* Set PHY 1 to Power Down (YUKON-2) */
279 #define PCI_PEX_LEGNAT BIT_15 /* PEX PM legacy/native mode (YUKON-2) */
289 #define PCI_CLS_OPT BIT_3 /* Cache Line Size opt. PCI-X (YUKON-2) */
310 /* PCI_OUR_STATUS 32 bit Adapter Status Register (Yukon-2) */
312 #define PCI_OS_PCIX BIT_30 /* PCI-X Bus */
313 #define PCI_OS_MODE_MSK (3<<28) /* Bit 29..28: PCI-X Bus Mode Mask */
315 #define PCI_OS_PCI_X BIT_26 /* PCI/PCI-X Bus (0 = PEX) */
320 #define PCI_OS_SPEED(val) ((val & PCI_OS_MODE_MSK) >> 28) /* PCI-X Speed */
323 #define PCI_OS_SPD_X66 1 /* PCI-X 66MHz Bus */
324 #define PCI_OS_SPD_X100 2 /* PCI-X 100MHz Bus */
325 #define PCI_OS_SPD_X133 3 /* PCI-X 133MHz Bus */
327 /* PCI_OUR_REG_3 32 bit Our Register 3 (Yukon-ECU only) */
330 /* PCI_OUR_REG_4 32 bit Our Register 4 (Yukon-ECU only) */
342 /* PCI_OUR_REG_5 32 bit Our Register 5 (Yukon-ECU only) */
345 #define PCI_CTL_SRESET_VMAIN_AV BIT_30 /* Soft Reset for Vmain_av De-Glitch */
346 #define PCI_CTL_BYPASS_VMAIN_AV BIT_29 /* Bypass En. for Vmain_av De-Glitch */
351 #define PCI_REL_PCIE_RST_DE_ASS BIT_26 /* PCIe Reset De-Asserted */
369 #define PCI_GAT_PME_DE_ASSERTED BIT_4 /* PME De-Asserted */
380 #define PCI_CF1_REL_PCIE_RESET BIT_21 /* PCI-E reset */
383 #define PCI_CF1_GAT_PCIE_RX_IDLE BIT_19 /* PCI-E Rx Electrical idle */
384 #define PCI_CF1_GAT_PCIE_RESET BIT_18 /* PCI-E Reset */
385 #define PCI_CF1_PRST_PHY_CLKREQ BIT_17 /* Enable PCI-E rst & PM2PHY gen. CLKREQ */
386 #define PCI_CF1_PCIE_RST_CLKREQ BIT_16 /* Enable PCI-E rst generate CLKREQ */
392 /* PEX_DEV_CTRL 16 bit PEX Device Control (Yukon-2) */
402 #define PEX_DC_EN_NFA_ER_RP BIT_1 /* Enable Non-Fatal Error Reporting */
407 /* PEX_LNK_STAT 16 bit PEX Link Status (Yukon-2) */
414 /* PEX_UNC_ERR_STAT PEX Uncorrectable Errors Status Register (Yukon-2) */
441 /* Special ISR registers (Yukon-2 only) */
450 * - completely empty (this is the RAP Block window)
466 #define B2_Y2_CLK_GATE 0x011d /* 8 bit Clock Gating (Yukon-2) */
467 #define B2_Y2_HW_RES 0x011e /* 8 bit HW Resources (Yukon-2) */
483 #define B2_I2C_CTRL 0x0160 /* 32 bit I2C HW Control Register */
484 #define B2_I2C_DATA 0x0164 /* 32 bit I2C HW Data Register */
485 #define B2_I2C_IRQ 0x0168 /* 32 bit I2C HW IRQ Register */
486 #define B2_I2C_SW 0x016c /* 32 bit I2C SW Port Register */
499 #define SELECT_RAM_BUFFER(rb, addr) (addr | (rb << 6)) /* Yukon-2 only */
502 /* Yukon-2: use SELECT_RAM_BUFFER() to access the RAM buffer */
504 * The HW-Spec. calls this registers Timeout Value 0..11. But this names are
525 * Bank 4 - 5
528 #define TXA_ITI_INI 0x0200 /* 32 bit Tx Arb Interval Timer Init Val*/
529 #define TXA_ITI_VAL 0x0204 /* 32 bit Tx Arb Interval Timer Value */
530 #define TXA_LIM_INI 0x0208 /* 32 bit Tx Arb Limit Counter Init Val */
531 #define TXA_LIM_VAL 0x020c /* 32 bit Tx Arb Limit Counter Value */
538 /* RSS key registers for Yukon-2 Family */
539 #define B4_RSS_KEY 0x0220 /* 4x32 bit RSS Key register (Yukon-2) */
545 /* 0x0280 - 0x0292: MAC 2 */
550 * Bank 8 - 15
601 * Bank 16 - 23
624 /* Receive GMAC FIFO (YUKON and Yukon-2), use MR_ADDR() to access */
630 #define RX_GMF_TR_THR 0x0c54 /* 32 bit Rx Truncation Threshold (Yukon-2) */
631 #define RX_GMF_UP_THR 0x0c58 /* 16 bit Rx Upper Pause Thr (Yukon-EC_U) */
632 #define RX_GMF_LP_THR 0x0c5a /* 16 bit Rx Lower Pause Thr (Yukon-EC_U) */
633 #define RX_GMF_VLAN 0x0c5c /* 32 bit Rx VLAN Type Register (Yukon-2) */
642 /* 0x0c80 - 0x0cbf: MAC 2 */
643 /* 0x0cc0 - 0x0cff: reserved */
648 /* Transmit GMAC FIFO (YUKON and Yukon-2), use MR_ADDR() to access */
652 #define TX_GMF_VLAN 0x0d5c /* 32 bit Tx VLAN Type Register (Yukon-2) */
663 /* 0x0d80 - 0x0dbf: MAC 2 */
664 /* 0x0daa - 0x0dff: reserved */
678 /* Polling Unit Registers (Yukon-2 only) */
683 /* ASF Subsystem Registers (Yukon-2 only) */
700 /* Status BMU Registers (Yukon-2 only)*/
711 /* FIFO Control/Status Registers (Yukon-2 only)*/
719 /* Level and ISR Timer Registers (Yukon-2 only)*/
748 /* Wake-up Frame Pattern Match Control Registers (YUKON only) */
750 #define WOL_REG_OFFS 0x20 /* HW-Bug: Address is + 0x20 against spec. */
757 #define WOL_PATT_PME 0x0f2a /* 8 bit WOL PME Match Enable (Yukon-2) */
758 #define WOL_PATT_ASFM 0x0f2b /* 8 bit WOL ASF Match Enable (Yukon-2) */
772 * Bank 32 - 33
777 /* offset to configuration space on Yukon-2 */
786 #define Y2_VMAIN_AVAIL BIT_17 /* VMAIN available (YUKON-2 only) */
787 #define Y2_VAUX_AVAIL BIT_16 /* VAUX available (YUKON-2 only) */
788 #define Y2_HW_WOL_ON BIT_15 /* HW WOL On (Yukon-EC Ultra A1 only) */
789 #define Y2_HW_WOL_OFF BIT_14 /* HW WOL Off (Yukon-EC Ultra A1 only) */
790 #define Y2_ASF_ENABLE BIT_13 /* ASF Unit Enable (YUKON-2 only) */
791 #define Y2_ASF_DISABLE BIT_12 /* ASF Unit Disable (YUKON-2 only) */
792 #define Y2_CLK_RUN_ENA BIT_11 /* CLK_RUN Enable (YUKON-2 only) */
793 #define Y2_CLK_RUN_DIS BIT_10 /* CLK_RUN Disable (YUKON-2 only) */
794 #define Y2_LED_STAT_ON BIT_9 /* Status LED On (YUKON-2 only) */
795 #define Y2_LED_STAT_OFF BIT_8 /* Status LED Off (YUKON-2 only) */
866 #define Y2_IS_PCI_EXP BIT_25 /* PCI-Express interrupt */
867 #define Y2_IS_PCI_NEXP BIT_24 /* PCI-Express error similar to PCI error */
898 #define CHIP_ID_YUKON_LITE 0xb1 /* Chip ID for YUKON-Lite (Rev. A1-A3) */
899 #define CHIP_ID_YUKON_LP 0xb2 /* Chip ID for YUKON-LP */
900 #define CHIP_ID_YUKON_XL 0xb3 /* Chip ID for YUKON-2 XL */
901 #define CHIP_ID_YUKON_EC_U 0xb4 /* Chip ID for YUKON-2 EC Ultra */
902 #define CHIP_ID_YUKON_EX 0xb5 /* Chip ID for YUKON-2 Extreme */
903 #define CHIP_ID_YUKON_EC 0xb6 /* Chip ID for YUKON-2 EC */
904 #define CHIP_ID_YUKON_FE 0xb7 /* Chip ID for YUKON-2 FE */
905 #define CHIP_ID_YUKON_FE_P 0xb8 /* Chip ID for YUKON-2 FE+ */
906 #define CHIP_ID_YUKON_SUPR 0xb9 /* Chip ID for YUKON-2 Supreme */
907 #define CHIP_ID_YUKON_UL_2 0xba /* Chip ID for YUKON-2 Ultra 2 */
909 #define CHIP_ID_YUKON_OPT 0xbc /* Chip ID for YUKON-2 Optima */
911 #define CHIP_REV_YU_XL_A0 0 /* Chip Rev. for Yukon-2 A0 */
912 #define CHIP_REV_YU_XL_A1 1 /* Chip Rev. for Yukon-2 A1 */
913 #define CHIP_REV_YU_XL_A2 2 /* Chip Rev. for Yukon-2 A2 */
914 #define CHIP_REV_YU_XL_A3 3 /* Chip Rev. for Yukon-2 A3 */
916 #define CHIP_REV_YU_EC_A1 0 /* Chip Rev. for Yukon-EC A1/A0 */
917 #define CHIP_REV_YU_EC_A2 1 /* Chip Rev. for Yukon-EC A2 */
918 #define CHIP_REV_YU_EC_A3 2 /* Chip Rev. for Yukon-EC A3 */
923 #define CHIP_REV_YU_FE_P_A0 0 /* Chip Rev. for Yukon-2 FE+ A0 */
925 #define CHIP_REV_YU_EX_A0 1 /* Chip Rev. for Yukon-2 EX A0 */
926 #define CHIP_REV_YU_EX_B0 2 /* Chip Rev. for Yukon-2 EX B0 */
928 #define CHIP_REV_YU_SU_A0 0 /* Chip Rev. for Yukon-2 SUPR A0 */
929 #define CHIP_REV_YU_SU_B0 1 /* Chip Rev. for Yukon-2 SUPR B0 */
930 #define CHIP_REV_YU_SU_B1 3 /* Chip Rev. for Yukon-2 SUPR B1 */
932 /* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */
942 /* B2_Y2_HW_RES 8 bit HW Resources (Yukon-2 only) */
953 /* B2_Y2_CLK_CTRL 32 bit Core Clock Frequency Control Register (Yukon-2/EC) */
954 /* Yukon-EC/FE */
957 /* Yukon-2 */
1008 /* B2_I2C_CTRL 32 bit I2C HW Control Register */
1011 #define I2C_DEV_SEL (0x7f<<9) /* Bit 15.. 9: I2C Device Select */
1013 #define I2C_DEV_SIZE (7<<1) /* Bit 3.. 1: I2C Device Size */
1022 #define I2C_STOP BIT_0 /* Interrupt I2C transfer */
1024 /* B2_I2C_IRQ 32 bit I2C HW IRQ Register */
1025 #define I2C_CLR_IRQ BIT_0 /* Clear I2C IRQ */
1027 /* B2_I2C_SW 32 bit (8 bit access) I2C HW SW Port Register */
1029 #define I2C_DATA BIT_1 /* I2C Data Port */
1030 #define I2C_CLK BIT_0 /* I2C Clock Port */
1032 /* I2C Address */
1033 #define I2C_SENS_ADDR LM80_ADDR /* I2C Sensor Address (Volt and Temp) */
1048 /* Y2_PEX_PHY_ADDR/DATA PEX PHY address and data reg (Yukon-2 only) */
1065 /* TXA_ITI_INI 32 bit Tx Arb Interval Timer Init Val */
1066 /* TXA_ITI_VAL 32 bit Tx Arb Interval Timer Value */
1067 /* TXA_LIM_INI 32 bit Tx Arb Limit Counter Init Val */
1068 /* TXA_LIM_VAL 32 bit Tx Arb Limit Counter Value */
1082 #define TXA_INT_T_ON BIT_5 /* Tx Arb Interval Timer Test On */
1083 #define TXA_INT_T_OFF BIT_4 /* Tx Arb Interval Timer Test Off */
1084 #define TXA_INT_T_STEP BIT_3 /* Tx Arb Interval Timer Step */
1085 #define TXA_LIM_T_ON BIT_2 /* Tx Arb Limit Timer Test On */
1086 #define TXA_LIM_T_OFF BIT_1 /* Tx Arb Limit Timer Test Off */
1087 #define TXA_LIM_T_STEP BIT_0 /* Tx Arb Limit Timer Step */
1095 /* Rx BMU Control / Status Registers (Yukon-2) */
1121 /* Tx BMU Control / Status Registers (Yukon-2) */
1129 #define F_TX_CHK_AUTO_OFF BIT_31 /* Tx checksum auto-calc Off(Yukon EX)*/
1130 #define F_TX_CHK_AUTO_ON BIT_30 /* Tx checksum auto-calc On(Yukon EX)*/
1140 /* Queue Prefetch Unit Offsets, use Y2_PREF_Q_ADDR() to address (Yukon-2 only)*/
1187 /* Threshold values for Yukon-EC Ultra */
1250 /* WOL_PATT_PME 8 bit WOL PME Match Enable (Yukon-2) */
1256 * Marvel-PHY Registers, indirect addressed over GMAC
1262 #define PHY_MARV_AUNE_ADV 0x04 /* 16 bit r/w Auto-Neg. Advertisement */
1264 #define PHY_MARV_AUNE_EXP 0x06 /* 16 bit r/o Auto-Neg. Expansion Reg */
1267 /* Marvel-specific registers */
1268 #define PHY_MARV_1000T_CTRL 0x09 /* 16 bit r/w 1000Base-T Control Reg */
1269 #define PHY_MARV_1000T_STAT 0x0a /* 16 bit r/o 1000Base-T Status Reg */
1270 /* 0x0b - 0x0e: reserved */
1298 #define PHY_CT_ANE (1<<12) /* Bit 12: Auto-Negotiation Enabled */
1301 #define PHY_CT_RE_CFG (1<<9) /* Bit 9: (sc) Restart Auto-Negotiation */
1312 #define PHY_ST_AN_OVER (1<<5) /* Bit 5: Auto-Negotiation Over */
1314 #define PHY_ST_AN_CAP (1<<3) /* Bit 3: Auto-Negotiation Capability */
1327 #define PHY_MARV_ID1_B2 0x0C25 /* Yukon-Plus (PHY 88E1011) */
1328 #define PHY_MARV_ID1_C2 0x0CC2 /* Yukon-EC (PHY 88E1111) */
1329 #define PHY_MARV_ID1_Y2 0x0C91 /* Yukon-2 (PHY 88E1112) */
1330 #define PHY_MARV_ID1_FE 0x0C83 /* Yukon-FE (PHY 88E3082 Rev.A1) */
1331 #define PHY_MARV_ID1_ECU 0x0CB0 /* Yukon-2 (PHY 88E1149 Rev.B2?) */
1333 /***** PHY_MARV_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
1342 /***** PHY_MARV_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement *****/
1349 #define PHY_M_AN_100_T4 BIT_9 /* Not cap. 100Base-T4 (always 0) */
1350 #define PHY_M_AN_100_FD BIT_8 /* Advertise 100Base-TX Full Duplex */
1351 #define PHY_M_AN_100_HD BIT_7 /* Advertise 100Base-TX Half Duplex */
1352 #define PHY_M_AN_10_FD BIT_6 /* Advertise 10Base-TX Full Duplex */
1353 #define PHY_M_AN_10_HD BIT_5 /* Advertise 10Base-TX Half Duplex */
1359 #define PHY_M_AN_1000X_AHD BIT_6 /* Advertise 10000Base-X Half Duplex */
1360 #define PHY_M_AN_1000X_AFD BIT_5 /* Advertise 10000Base-X Full Duplex */
1368 /***** PHY_MARV_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
1372 #define PHY_M_1000C_MPD BIT_10 /* Multi-Port Device */
1399 /* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
1446 #define PHY_M_IS_AN_ERROR BIT_15 /* Auto-Negotiation Error */
1450 #define PHY_M_IS_AN_COMPL BIT_11 /* Auto-Negotiation Completed */
1479 #define PHY_M_EC_FIB_AN_ENA BIT_3 /* Fiber Auto-Neg. Enable (88E1011S only) */
1613 #define PHY_M_FESC_SEL_CL_A BIT_0 /* Select Class A driver (100B-TX) */
1615 /* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
1623 #define PHY_M_MAC_MD_AUTO 3 /* Auto Copper/1000Base-X */
1625 #define PHY_M_MAC_MD_1000BX 7 /* 1000Base-X only */
1669 #define GM_TX_FLOW_CTRL 0x0010 /* 16 bit r/w Transmit Flow-Control */
1707 * MIB Counters base address definitions (low word) -
1737 (GM_MIB_CNT_BASE + 104) /* 65-127 Byte Rx Frame */
1739 (GM_MIB_CNT_BASE + 112) /* 128-255 Byte Rx Frame */
1741 (GM_MIB_CNT_BASE + 120) /* 256-511 Byte Rx Frame */
1743 (GM_MIB_CNT_BASE + 128) /* 512-1023 Byte Rx Frame */
1745 (GM_MIB_CNT_BASE + 136) /* 1024-1518 Byte Rx Frame */
1747 (GM_MIB_CNT_BASE + 144) /* 1519-MaxSize Byte Rx Frame */
1773 (GM_MIB_CNT_BASE + 248) /* 65-127 Byte Tx Frame */
1775 (GM_MIB_CNT_BASE + 256) /* 128-255 Byte Tx Frame */
1777 (GM_MIB_CNT_BASE + 264) /* 256-511 Byte Tx Frame */
1779 (GM_MIB_CNT_BASE + 272) /* 512-1023 Byte Tx Frame */
1781 (GM_MIB_CNT_BASE + 280) /* 1024-1518 Byte Tx Frame */
1783 (GM_MIB_CNT_BASE + 288) /* 1519-MaxSize Byte Tx Frame */
1799 /*----------------------------------------------------------------------------*/
1813 #define GM_GPSR_FC_TX_DIS BIT_13 /* Tx Flow-Control Mode Disabled */
1822 #define GM_GPSR_FC_RX_DIS BIT_2 /* Rx Flow-Control Mode Disabled */
1825 #define GM_GPCR_RMII_PH_ENA BIT_15 /* Enable RMII for PHY (Yukon-FE only) */
1826 #define GM_GPCR_RMII_LB_ENA BIT_14 /* Enable RMII Loopback (Yukon-FE only) */
1827 #define GM_GPCR_FC_TX_DIS BIT_13 /* Disable Tx Flow-Control Mode */
1835 #define GM_GPCR_FC_RX_DIS BIT_4 /* Disable Rx Flow-Control Mode */
1837 #define GM_GPCR_AU_DUP_DIS BIT_2 /* Disable Auto-Update Duplex */
1838 #define GM_GPCR_AU_FCT_DIS BIT_1 /* Disable Auto-Update Flow-C. */
1839 #define GM_GPCR_AU_SPD_DIS BIT_0 /* Disable Auto-Update Speed */
1846 #define GM_TXCR_FORCE_JAM BIT_15 /* Force Jam / Flow-Control */
1851 /* (Yukon-2 only) */
1859 #define GM_RXCR_CRC_DIS BIT_13 /* Remove 4-byte CRC */
1860 #define GM_RXCR_PASS_FC BIT_12 /* Pass FC packets to FIFO (Yukon-1 only) */
1867 /* (Yukon-2 only) */
1881 /* r/o on Yukon, r/w on Yukon-EC */
1885 #define GM_SMOD_IPG_MSK 0x1f /* Bit 4.. 0: Inter-Packet Gap (IPG) */
1915 #define GMR_FS_GOOD_FC BIT_7 /* Good Flow-Control Packet */
1916 #define GMR_FS_BAD_FC BIT_6 /* Bad Flow-Control Packet */
1982 /* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test (YUKON and Yukon-2) */
1983 #define TX_STFW_DIS BIT_31 /* Disable Store & Forward (Yukon-EC Ultra) */
1984 #define TX_STFW_ENA BIT_30 /* Enable Store & Forward (Yukon-EC Ultra) */
1987 #define TX_JUMBO_ENA BIT_23 /* Enable Jumbo Mode (Yukon-EC Ultra) */
1988 #define TX_JUMBO_DIS BIT_22 /* Disable Jumbo Mode (Yukon-EC Ultra) */
2009 /* POLL_CTRL 32 bit Polling Unit control register (Yukon-2 only) */
2055 /* STAT_CTRL 32 bit Status BMU control register (Yukon-2 only) */
2081 #define GPC_SEL_BDT BIT_28 /* Select Bi-Dir. Transfer for MDC/MDIO */
2125 bus_write_4((sc)->msk_res[0], (reg), (val))
2127 bus_write_2((sc)->msk_res[0], (reg), (val))
2129 bus_write_1((sc)->msk_res[0], (reg), (val))
2132 bus_read_4((sc)->msk_res[0], (reg))
2134 bus_read_2((sc)->msk_res[0], (reg))
2136 bus_read_1((sc)->msk_res[0], (reg))
2139 bus_write_4((sc)->msk_res[0], Y2_CFG_SPC + (reg), (val))
2141 bus_write_2((sc)->msk_res[0], Y2_CFG_SPC + (reg), (val))
2143 bus_write_1((sc)->msk_res[0], Y2_CFG_SPC + (reg), (val))
2146 bus_read_4((sc)->msk_res[0], Y2_CFG_SPC + (reg))
2148 bus_read_2((sc)->msk_res[0], Y2_CFG_SPC + (reg))
2150 bus_read_1((sc)->msk_res[0], Y2_CFG_SPC + (reg))
2153 CSR_READ_4((sc_if)->msk_softc, (reg))
2155 CSR_READ_2((sc_if)->msk_softc, (reg))
2157 CSR_READ_1((sc_if)->msk_softc, (reg))
2160 CSR_WRITE_4((sc_if)->msk_softc, (reg), (val))
2162 CSR_WRITE_2((sc_if)->msk_softc, (reg), (val))
2164 CSR_WRITE_1((sc_if)->msk_softc, (reg), (val))
2167 ((BASE_GMAC_1 + (port) * (BASE_GMAC_2 - BASE_GMAC_1)) | (reg))
2221 /* YUKON-2 bit values */
2227 /* YUKON-2 Control flags */
2244 /* YUKON-2 Rx/Tx opcodes defines */
2265 /* YUKON-2 STATUS opcodes defines */
2275 /* YUKON-2 SPECIAL opcodes defines */
2357 #define MSK_JUMBO_MTU (MSK_JUMBO_FRAMELEN-ETHER_HDR_LEN-ETHER_CRC_LEN)
2359 (ETHER_MAX_LEN + ETHER_VLAN_ENCAP_LEN - ETHER_CRC_LEN)
2360 #define MSK_MIN_FRAMELEN (ETHER_MIN_LEN - ETHER_CRC_LEN)
2412 ((sc)->msk_rdata.msk_tx_ring_paddr + sizeof(struct msk_tx_desc) * (i))
2414 ((sc)->msk_rdata.msk_rx_ring_paddr + sizeof(struct msk_rx_desc) * (i))
2416 ((sc)->msk_rdata.msk_jumbo_rx_ring_paddr + sizeof(struct msk_rx_desc) * (i))
2442 #define MSK_PROC_MAX (MSK_RX_RING_CNT - 1)
2543 #define MSK_LOCK(_sc) mtx_lock(&(_sc)->msk_mtx)
2544 #define MSK_UNLOCK(_sc) mtx_unlock(&(_sc)->msk_mtx)
2545 #define MSK_LOCK_ASSERT(_sc) mtx_assert(&(_sc)->msk_mtx, MA_OWNED)
2546 #define MSK_IF_LOCK(_sc) MSK_LOCK((_sc)->msk_softc)
2547 #define MSK_IF_UNLOCK(_sc) MSK_UNLOCK((_sc)->msk_softc)
2548 #define MSK_IF_LOCK_ASSERT(_sc) MSK_LOCK_ASSERT((_sc)->msk_softc)
2550 #define MSK_USECS(sc, us) ((sc)->msk_clock * (us))