Lines Matching +full:jh7100 +full:- +full:pinctrl

1 // SPDX-License-Identifier: GPL-2.0 OR MIT
7 /dts-v1/;
8 #include "jh7100.dtsi"
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/leds/common.h>
11 #include <dt-bindings/pinctrl/pinctrl-starfive-jh7100.h>
21 		stdout-path = "serial0:115200n8";
25 		timebase-frequency = <6250000>;
34 		compatible = "gpio-leds";
36 		led-ack {
40 			linux,default-trigger = "heartbeat";
45 	reserved-memory {
46 		#address-cells = <2>;
47 		#size-cells = <2>;
50 		dma-reserved@fa000000 {
52 			no-map;
56 			compatible = "shared-dma-pool";
58 			no-map;
59 			linux,dma-default;
64 		dma-ranges = <0x00 0x80000000 0x00 0x80000000 0x00 0x7a000000>,
69 	wifi_pwrseq: wifi-pwrseq {
70 		compatible = "mmc-pwrseq-simple";
71 		reset-gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
76 	i2c0_pins: i2c0-0 {
77 		i2c-pins {
84 			bias-disable; /* external pull-up */
85 			input-enable;
86 			input-schmitt-enable;
90 	i2c1_pins: i2c1-0 {
91 		i2c-pins {
98 			bias-pull-up;
99 			input-enable;
100 			input-schmitt-enable;
104 	i2c2_pins: i2c2-0 {
105 		i2c-pins {
112 			bias-disable; /* external pull-up */
113 			input-enable;
114 			input-schmitt-enable;
118 	sdio0_pins: sdio0-0 {
119 		clk-pins {
122 			bias-disable;
123 			input-disable;
124 			input-schmitt-disable;
126 		sdio-pins {
149 			bias-pull-up;
150 			input-enable;
151 			input-schmitt-enable;
155 	sdio1_pins: sdio1-0 {
156 		clk-pins {
159 			bias-disable;
160 			input-disable;
161 			input-schmitt-disable;
163 		sdio-pins {
184 			bias-pull-up;
185 			input-enable;
186 			input-schmitt-enable;
190 	uart3_pins: uart3-0 {
191 		rx-pins {
194 			bias-pull-up;
195 			drive-strength = <14>;
196 			input-enable;
197 			input-schmitt-enable;
198 			slew-rate = <0>;
200 		tx-pins {
203 			bias-disable;
204 			drive-strength = <35>;
205 			input-disable;
206 			input-schmitt-disable;
207 			slew-rate = <0>;
213 	clock-frequency = <100000>;
214 	i2c-sda-hold-time-ns = <300>;
215 	i2c-sda-falling-time-ns = <500>;
216 	i2c-scl-falling-time-ns = <500>;
217 	pinctrl-names = "default";
218 	pinctrl-0 = <&i2c0_pins>;
224 		gpio-controller;
225 		#gpio-cells = <2>;
233 	clock-frequency = <400000>;
234 	i2c-sda-hold-time-ns = <300>;
235 	i2c-sda-falling-time-ns = <100>;
236 	i2c-scl-falling-time-ns = <100>;
237 	pinctrl-names = "default";
238 	pinctrl-0 = <&i2c1_pins>;
243 	clock-frequency = <100000>;
244 	i2c-sda-hold-time-ns = <300>;
245 	i2c-sda-falling-time-ns = <500>;
246 	i2c-scl-falling-time-ns = <500>;
247 	pinctrl-names = "default";
248 	pinctrl-0 = <&i2c2_pins>;
253 	clock-frequency = <25000000>;
257 	clock-frequency = <27000000>;
261 	broken-cd;
262 	bus-width = <4>;
263 	cap-sd-highspeed;
264 	pinctrl-names = "default";
265 	pinctrl-0 = <&sdio0_pins>;
270 	#address-cells = <1>;
271 	#size-cells = <0>;
272 	bus-width = <4>;
273 	cap-sd-highspeed;
274 	cap-sdio-irq;
275 	cap-power-off-card;
276 	mmc-pwrseq = <&wifi_pwrseq>;
277 	non-removable;
278 	pinctrl-names = "default";
279 	pinctrl-0 = <&sdio1_pins>;
283 		compatible = "brcm,bcm4329-fmac";
289 	pinctrl-names = "default";
290 	pinctrl-0 = <&uart3_pins>;