Lines Matching +full:0 +full:xb00

20 		#size-cells = <0>;
22 		PowerPC,5200@0 {
24 			reg = <0>;
27 			d-cache-size = <0x4000>;	// L1, 16K
28 			i-cache-size = <0x4000>;	// L1, 16K
29 			timebase-frequency = <0>;	// from bootloader
30 			bus-frequency = <0>;		// from bootloader
31 			clock-frequency = <0>;		// from bootloader
35 	memory@0 {
37 		reg = <0x00000000 0x04000000>;	// 64MB
44 		ranges = <0 0xf0000000 0x0000c000>;
45 		reg = <0xf0000000 0x00000100>;
46 		bus-frequency = <0>;		// from bootloader
47 		system-frequency = <0>;		// from bootloader
51 			reg = <0x200 0x38>;
59 			reg = <0x500 0x80>;
64 			reg = <0x600 0x10>;
65 			interrupts = <1 9 0>;
71 			interrupts = <2 17 0>;
72 			reg = <0x900 0x80>;
77 			interrupts = <2 18 0>;
78 			reg = <0x980 0x80>;
83 			reg = <0xb00 0x40>;
84 			interrupts = <1 7 0>;
91 			reg = <0x1000 0xff>;
92 			interrupts = <2 6 0>;
97 			reg = <0x1200 0x80>;
98 			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
99 			              3 4 0  3 5 0  3 6 0  3 7 0
100 			              3 8 0  3 9 0  3 10 0  3 11 0
101 			              3 12 0  3 13 0  3 14 0  3 15 0>;
106 			reg = <0x1f00 0x100>;
111 			reg = <0x2000 0x100>;
112 			interrupts = <2 1 0>;
117 			reg = <0x2200 0x100>;
118 			interrupts = <2 2 0>;
123 			reg = <0x2400 0x100>;
124 			interrupts = <2 3 0>;
129 			reg = <0x3000 0x400>;
131 			interrupts = <2 5 0>;
137 			#size-cells = <0>;
139 			reg = <0x3000 0x400>;       // fec range, since we need to setup fec interrupts
140 			interrupts = <2 5 0>;   // these are for "mii command finished", not link changes & co.
142 			phy0: ethernet-phy@0 {
143 				reg = <0>;
149 			reg = <0x3a00 0x100>;
150 			interrupts = <2 7 0>;
155 			#size-cells = <0>;
157 			reg = <0x3d40 0x40>;
158 			interrupts = <2 16 0>;
162 				reg = <0x68>;
168 			reg = <0x8000 0x4000>;
176 		ranges = <0 0 0xfc000000 0x02000000>;
178 		flash@0,0 {
180 			reg = <0 0 0x02000000>;
194 		reg = <0xf0000d00 0x100>;
195 		interrupt-map-mask = <0xf800 0 0 7>;
196 		interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3
197 				 0xc000 0 0 2 &mpc5200_pic 0 0 3
198 				 0xc000 0 0 3 &mpc5200_pic 0 0 3
199 				 0xc000 0 0 4 &mpc5200_pic 0 0 3>;
200 		clock-frequency = <0>; // From boot loader
201 		interrupts = <2 8 0 2 9 0 2 10 0>;
202 		bus-range = <0 0>;
203 		ranges = <0x42000000 0 0x80000000 0x80000000 0 0x10000000>,
204 			 <0x02000000 0 0x90000000 0x90000000 0 0x10000000>,
205 			 <0x01000000 0 0x00000000 0xa0000000 0 0x01000000>;