Lines Matching +full:r8a779f0 +full:- +full:ufs

1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/leds/common.h>
11 #include "r8a779f0.dtsi"
15 	compatible = "renesas,spider-cpu", "renesas,r8a779f0";
24 		stdout-path = "serial0:1843200n8";
28 		compatible = "gpio-leds";
30 		led-7 {
34 			function-enumerator = <7>;
37 		led-8 {
41 			function-enumerator = <8>;
56 	rc21012_pci: clk-rc21012-pci {
57 		compatible = "fixed-clock";
58 		clock-frequency = <100000000>;
59 		#clock-cells = <0>;
62 	rc21012_ufs: clk-rc21012-ufs {
63 		compatible = "fixed-clock";
64 		clock-frequency = <38400000>;
65 		#clock-cells = <0>;
68 	reg_1p8v: regulator-1p8v {
69 		compatible = "regulator-fixed";
70 		regulator-name = "fixed-1.8V";
71 		regulator-min-microvolt = <1800000>;
72 		regulator-max-microvolt = <1800000>;
73 		regulator-boot-on;
74 		regulator-always-on;
77 	reg_3p3v: regulator-3p3v {
78 		compatible = "regulator-fixed";
79 		regulator-name = "fixed-3.3V";
80 		regulator-min-microvolt = <3300000>;
81 		regulator-max-microvolt = <3300000>;
82 		regulator-boot-on;
83 		regulator-always-on;
88 	clock-frequency = <20000000>;
92 	clock-frequency = <32768>;
96 	pinctrl-0 = <&hscif0_pins>;
97 	pinctrl-names = "default";
99 	uart-has-rtscts;
104 	pinctrl-0 = <&i2c0_pins>;
105 	pinctrl-names = "default";
108 	clock-frequency = <400000>;
113 		gpio-controller;
114 		#gpio-cells = <2>;
116 		rc21012-gpio2-hog {
117 			gpio-hog;
119 			output-high;
125 	pinctrl-0 = <&i2c4_pins>;
126 	pinctrl-names = "default";
129 	clock-frequency = <400000>;
133 		label = "cpu-board";
144 	pinctrl-0 = <&mmc_pins>;
145 	pinctrl-1 = <&mmc_pins>;
146 	pinctrl-names = "default", "state_uhs";
148 	vmmc-supply = <&reg_3p3v>;
149 	vqmmc-supply = <&reg_1p8v>;
150 	mmc-hs200-1_8v;
151 	mmc-hs400-1_8v;
152 	bus-width = <8>;
153 	no-sd;
154 	no-sdio;
155 	non-removable;
156 	full-pwr-cycle-in-suspend;
161 	compatible = "gpio-gate-clock";
163 	enable-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
164 	/delete-property/ clock-frequency;
168 	reset-gpio = <&gpio_exp_20 0 GPIO_ACTIVE_LOW>;
173 	pinctrl-0 = <&scif_clk_pins>;
174 	pinctrl-names = "default";
194 		power-source = <1800>;
209 	timeout-sec = <60>;
214 	pinctrl-0 = <&scif0_pins>;
215 	pinctrl-names = "default";
217 	uart-has-rtscts;
222 	clock-frequency = <24000000>;
225 &ufs {
230 	compatible = "gpio-gate-clock";
232 	enable-gpios = <&gpio_exp_20 4 GPIO_ACTIVE_LOW>;
233 	/delete-property/ clock-frequency;