Lines Matching +full:vdd +full:- +full:1
1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
8 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
9 #include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
10 #include <dt-bindings/iio/qcom,spmi-adc7-pm8350b.h>
11 #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
12 #include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
13 #include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
24 compatible = "qcom,sm8450-hdk", "qcom,sm8450";
25 chassis-type = "embedded";
31 wcd938x: audio-codec {
32 compatible = "qcom,wcd9385-codec";
34 pinctrl-names = "default";
35 pinctrl-0 = <&wcd_default>;
37 qcom,micbias1-microvolt = <1800000>;
38 qcom,micbias2-microvolt = <1800000>;
39 qcom,micbias3-microvolt = <1800000>;
40 qcom,micbias4-microvolt = <1800000>;
41 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
42 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
43 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
44 qcom,rx-device = <&wcd_rx>;
45 qcom,tx-device = <&wcd_tx>;
47 reset-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
49 vdd-buck-supply = <&vreg_s10b_1p8>;
50 vdd-rxtx-supply = <&vreg_s10b_1p8>;
51 vdd-io-supply = <&vreg_s10b_1p8>;
52 vdd-mic-bias-supply = <&vreg_bob>;
54 #sound-dai-cells = <1>;
58 stdout-path = "serial0:115200n8";
61 hdmi-out {
62 compatible = "hdmi-connector";
67 remote-endpoint = <<9611_out>;
72 lt9611_1v2: lt9611-vdd12-regulator {
73 compatible = "regulator-fixed";
74 regulator-name = "LT9611_1V2";
76 vin-supply = <&vph_pwr>;
77 regulator-min-microvolt = <1200000>;
78 regulator-max-microvolt = <1200000>;
80 enable-active-high;
83 lt9611_3v3: lt9611-3v3-regulator {
84 compatible = "regulator-fixed";
85 regulator-name = "LT9611_3V3";
87 vin-supply = <&vreg_bob>;
89 regulator-min-microvolt = <3300000>;
90 regulator-max-microvolt = <3300000>;
91 enable-active-high;
94 pmic-glink {
95 compatible = "qcom,sm8450-pmic-glink", "qcom,pmic-glink";
96 #address-cells = <1>;
97 #size-cells = <0>;
100 compatible = "usb-c-connector";
102 power-role = "dual";
103 data-role = "dual";
106 #address-cells = <1>;
107 #size-cells = <0>;
113 remote-endpoint = <&usb_1_dwc3_hs>;
117 port@1 {
118 reg = <1>;
121 remote-endpoint = <&usb_1_qmpphy_out>;
129 remote-endpoint = <&fsa4480_sbu_mux>;
137 thermal-zones {
138 camera-thermal {
139 polling-delay-passive = <250>;
140 polling-delay = <0>;
141 thermal-sensors = <&pmk8350_adc_tm 2>;
144 active-config0 {
152 rear-tof-thermal {
153 polling-delay-passive = <250>;
154 polling-delay = <0>;
155 thermal-sensors = <&pmk8350_adc_tm 5>;
158 active-config0 {
166 skin-msm-thermal {
167 polling-delay-passive = <250>;
168 polling-delay = <0>;
169 thermal-sensors = <&pmk8350_adc_tm 1>;
172 active-config0 {
180 therm1-thermal {
181 polling-delay-passive = <250>;
182 polling-delay = <0>;
183 thermal-sensors = <&pmk8350_adc_tm 3>;
186 active-config0 {
194 therm2-thermal {
195 polling-delay-passive = <250>;
196 polling-delay = <0>;
197 thermal-sensors = <&pmk8350_adc_tm 6>;
200 active-config0 {
208 usb-conn-thermal {
209 polling-delay-passive = <250>;
210 polling-delay = <0>;
211 thermal-sensors = <&pmk8350_adc_tm 7>;
214 active-config0 {
222 wide-rfc-thermal {
223 polling-delay-passive = <250>;
224 polling-delay = <0>;
225 thermal-sensors = <&pmk8350_adc_tm 4>;
228 active-config0 {
236 xo-thermal {
237 polling-delay-passive = <0>;
238 polling-delay = <0>;
239 thermal-sensors = <&pmk8350_adc_tm 0>;
242 active-config0 {
251 vph_pwr: vph-pwr-regulator {
252 compatible = "regulator-fixed";
253 regulator-name = "vph_pwr";
254 regulator-min-microvolt = <3700000>;
255 regulator-max-microvolt = <3700000>;
257 regulator-always-on;
258 regulator-boot-on;
263 regulators-0 {
264 compatible = "qcom,pm8350-rpmh-regulators";
265 qcom,pmic-id = "b";
267 vdd-s1-supply = <&vph_pwr>;
268 vdd-s2-supply = <&vph_pwr>;
269 vdd-s3-supply = <&vph_pwr>;
270 vdd-s4-supply = <&vph_pwr>;
271 vdd-s5-supply = <&vph_pwr>;
272 vdd-s6-supply = <&vph_pwr>;
273 vdd-s7-supply = <&vph_pwr>;
274 vdd-s8-supply = <&vph_pwr>;
275 vdd-s9-supply = <&vph_pwr>;
276 vdd-s10-supply = <&vph_pwr>;
277 vdd-s11-supply = <&vph_pwr>;
278 vdd-s12-supply = <&vph_pwr>;
280 vdd-l1-l4-supply = <&vreg_s11b_0p95>;
281 vdd-l2-l7-supply = <&vreg_bob>;
282 vdd-l3-l5-supply = <&vreg_bob>;
283 vdd-l6-l9-l10-supply = <&vreg_s12b_1p25>;
284 vdd-l8-supply = <&vreg_s2h_0p95>;
287 regulator-name = "vreg_s10b_1p8";
288 regulator-min-microvolt = <1800000>;
289 regulator-max-microvolt = <1800000>;
293 regulator-name = "vreg_s11b_0p95";
294 regulator-min-microvolt = <966000>;
295 regulator-max-microvolt = <1104000>;
299 regulator-name = "vreg_s12b_1p25";
300 regulator-min-microvolt = <1350000>;
301 regulator-max-microvolt = <1400000>;
305 regulator-name = "vreg_l1b_0p91";
306 regulator-min-microvolt = <912000>;
307 regulator-max-microvolt = <920000>;
308 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
312 regulator-name = "vreg_l2b_3p07";
313 regulator-min-microvolt = <3072000>;
314 regulator-max-microvolt = <3072000>;
315 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
319 regulator-name = "vreg_l3b_0p9";
320 regulator-min-microvolt = <904000>;
321 regulator-max-microvolt = <904000>;
322 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
326 regulator-name = "vreg_l5b_0p88";
327 regulator-min-microvolt = <880000>;
328 regulator-max-microvolt = <888000>;
329 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
333 regulator-name = "vreg_l6b_1p2";
334 regulator-min-microvolt = <1200000>;
335 regulator-max-microvolt = <1200000>;
336 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
340 regulator-name = "vreg_l7b_2p5";
341 regulator-min-microvolt = <2504000>;
342 regulator-max-microvolt = <2504000>;
343 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
347 regulator-name = "vreg_l9b_1p2";
348 regulator-min-microvolt = <1200000>;
349 regulator-max-microvolt = <1200000>;
350 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
354 regulators-1 {
355 compatible = "qcom,pm8350c-rpmh-regulators";
356 qcom,pmic-id = "c";
358 vdd-s1-supply = <&vph_pwr>;
359 vdd-s2-supply = <&vph_pwr>;
360 vdd-s3-supply = <&vph_pwr>;
361 vdd-s4-supply = <&vph_pwr>;
362 vdd-s5-supply = <&vph_pwr>;
363 vdd-s6-supply = <&vph_pwr>;
364 vdd-s7-supply = <&vph_pwr>;
365 vdd-s8-supply = <&vph_pwr>;
366 vdd-s9-supply = <&vph_pwr>;
367 vdd-s10-supply = <&vph_pwr>;
369 vdd-l1-l12-supply = <&vreg_bob>;
370 vdd-l2-l8-supply = <&vreg_bob>;
371 vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
372 vdd-l6-l9-l11-supply = <&vreg_bob>;
373 vdd-l10-supply = <&vreg_s12b_1p25>;
375 vdd-bob-supply = <&vph_pwr>;
378 regulator-name = "vreg_s1c_1p86";
379 regulator-min-microvolt = <1800000>;
380 regulator-max-microvolt = <2024000>;
384 regulator-name = "vreg_s10c_1p05";
385 regulator-min-microvolt = <1000000>;
386 regulator-max-microvolt = <1100000>;
390 regulator-name = "vreg_bob";
391 regulator-min-microvolt = <3008000>;
392 regulator-max-microvolt = <3960000>;
393 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
397 regulator-name = "vreg_l1c_1p8";
398 regulator-min-microvolt = <1800000>;
399 regulator-max-microvolt = <1800000>;
400 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
404 regulator-name = "vreg_l3c_3p0";
405 regulator-min-microvolt = <3296000>;
406 regulator-max-microvolt = <3304000>;
407 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
411 regulator-name = "vreg_l4c_1p8";
412 regulator-min-microvolt = <1704000>;
413 regulator-max-microvolt = <3000000>;
414 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
418 regulator-name = "vreg_l5c_1p8";
419 regulator-min-microvolt = <1704000>;
420 regulator-max-microvolt = <3000000>;
421 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
425 regulator-name = "vreg_l6c_1p8";
426 regulator-min-microvolt = <1800000>;
427 regulator-max-microvolt = <3008000>;
428 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
432 regulator-name = "vreg_l7c_3p0";
433 regulator-min-microvolt = <3008000>;
434 regulator-max-microvolt = <3008000>;
435 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
439 regulator-name = "vreg_l8c_1p8";
440 regulator-min-microvolt = <1800000>;
441 regulator-max-microvolt = <1800000>;
442 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
446 regulator-name = "vreg_l9c_2p96";
447 regulator-min-microvolt = <2960000>;
448 regulator-max-microvolt = <3008000>;
449 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
453 regulator-name = "vreg_l12c_1p8";
454 regulator-min-microvolt = <1800000>;
455 regulator-max-microvolt = <1968000>;
456 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
460 regulator-name = "vreg_l13c_3p0";
461 regulator-min-microvolt = <3000000>;
462 regulator-max-microvolt = <3000000>;
463 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
467 regulators-2 {
468 compatible = "qcom,pm8450-rpmh-regulators";
469 qcom,pmic-id = "h";
471 vdd-s1-supply = <&vph_pwr>;
472 vdd-s2-supply = <&vph_pwr>;
473 vdd-s3-supply = <&vph_pwr>;
474 vdd-s4-supply = <&vph_pwr>;
475 vdd-s5-supply = <&vph_pwr>;
476 vdd-s6-supply = <&vph_pwr>;
478 vdd-l2-supply = <&vreg_bob>;
479 vdd-l3-supply = <&vreg_bob>;
480 vdd-l4-supply = <&vreg_bob>;
483 regulator-name = "vreg_s2h_0p95";
484 regulator-min-microvolt = <848000>;
485 regulator-max-microvolt = <1104000>;
489 regulator-name = "vreg_s3h_0p5";
490 regulator-min-microvolt = <500000>;
491 regulator-max-microvolt = <500000>;
495 regulator-name = "vreg_l2h_0p91";
496 regulator-min-microvolt = <880000>;
497 regulator-max-microvolt = <912000>;
498 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
502 regulator-name = "vreg_l3h_0p91";
503 regulator-min-microvolt = <912000>;
504 regulator-max-microvolt = <912000>;
505 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
509 regulators-3 {
510 compatible = "qcom,pmr735a-rpmh-regulators";
511 qcom,pmic-id = "e";
513 vdd-s1-supply = <&vph_pwr>;
514 vdd-s2-supply = <&vph_pwr>;
515 vdd-s3-supply = <&vph_pwr>;
517 vdd-l1-l2-supply = <&vreg_s2e_0p85>;
518 vdd-l3-supply = <&vreg_s1e_1p25>;
519 vdd-l4-supply = <&vreg_s1c_1p86>;
520 vdd-l5-l6-supply = <&vreg_s1c_1p86>;
521 vdd-l7-bob-supply = <&vreg_bob>;
524 regulator-name = "vreg_s1e_1p25";
525 regulator-min-microvolt = <1200000>;
526 regulator-max-microvolt = <1296000>;
530 regulator-name = "vreg_s2e_0p85";
531 regulator-min-microvolt = <500000>;
532 regulator-max-microvolt = <1040000>;
536 regulator-name = "vreg_l1e_0p8";
537 regulator-min-microvolt = <800000>;
538 regulator-max-microvolt = <800000>;
542 regulator-name = "vreg_l2e_0p8";
543 regulator-min-microvolt = <800000>;
544 regulator-max-microvolt = <800000>;
548 regulator-name = "vreg_l3e_1p2";
549 regulator-min-microvolt = <1200000>;
550 regulator-max-microvolt = <1200000>;
554 regulator-name = "vreg_l4e_1p7";
555 regulator-min-microvolt = <1776000>;
556 regulator-max-microvolt = <1776000>;
560 regulator-name = "vreg_l5e_0p88";
561 regulator-min-microvolt = <880000>;
562 regulator-max-microvolt = <880000>;
566 regulator-name = "vreg_l6e_1p2";
567 regulator-min-microvolt = <1200000>;
568 regulator-max-microvolt = <1200000>;
572 regulator-name = "vreg_l7e_2p8";
573 regulator-min-microvolt = <2800000>;
574 regulator-max-microvolt = <2800000>;
586 zap-shader {
587 firmware-name = "qcom/sm8450/a730_zap.mbn";
592 clock-frequency = <400000>;
595 lt9611_codec: hdmi-bridge@2b {
599 interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
601 reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
603 vdd-supply = <<9611_1v2>;
604 vcc-supply = <<9611_3v3>;
606 pinctrl-names = "default";
607 pinctrl-0 = <<9611_irq_pin <9611_rst_pin>;
610 #address-cells = <1>;
611 #size-cells = <0>;
617 remote-endpoint = <&mdss_dsi0_out>;
625 remote-endpoint = <&hdmi_connector_out>;
633 clock-frequency = <100000>;
637 typec-mux@42 {
641 interrupts-extended = <&tlmm 2 IRQ_TYPE_LEVEL_LOW>;
643 vcc-supply = <&vreg_bob>;
644 mode-switch;
645 orientation-switch;
649 remote-endpoint = <&pmic_glink_sbu>;
660 vdda-supply = <&vreg_l6b_1p2>;
665 remote-endpoint = <<9611_a>;
666 data-lanes = <0 1 2 3>;
670 vdds-supply = <&vreg_l5b_0p88>;
678 port@1 {
679 reg = <1>;
682 data-lanes = <0 1>;
683 remote-endpoint = <&usb_1_qmpphy_dp_in>;
691 max-link-speed = <2>;
696 vdda-phy-supply = <&vreg_l5b_0p88>;
697 vdda-pll-supply = <&vreg_l6b_1p2>;
706 vdda-phy-supply = <&vreg_l2h_0p91>;
707 vdda-pll-supply = <&vreg_l6b_1p2>;
711 io-channels = <&pmk8350_vadc PM8350_ADC7_DIE_TEMP(1)>;
712 io-channel-names = "thermal";
716 io-channels = <&pmk8350_vadc PM8350B_ADC7_DIE_TEMP>;
717 io-channel-names = "thermal";
721 io-channels = <&pmk8350_vadc PMR735A_ADC7_DIE_TEMP>;
722 io-channel-names = "thermal";
728 xo-therm@0 {
730 io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
732 qcom,hw-settle-time-us = <200>;
735 skin-msm-therm@1 {
736 reg = <1>;
737 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
739 qcom,hw-settle-time-us = <200>;
742 camera-therm@2 {
744 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
746 qcom,hw-settle-time-us = <200>;
749 therm1-therm@3 {
751 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
753 qcom,hw-settle-time-us = <200>;
756 wide-rfc-therm@4 {
758 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
760 qcom,hw-settle-time-us = <200>;
763 rear-tof-therm@5 {
765 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM5_100K_PU(1)>;
767 qcom,hw-settle-time-us = <200>;
770 therm2-therm@6 {
772 io-channels = <&pmk8350_vadc PM8350_ADC7_GPIO3_100K_PU(1)>;
774 qcom,hw-settle-time-us = <200>;
777 usb-conn-therm@7 {
779 io-channels = <&pmk8350_vadc PM8350B_ADC7_AMUX_THM5_100K_PU>;
781 qcom,hw-settle-time-us = <200>;
795 qcom,hw-settle-time = <200>;
801 reg = <PM8350_ADC7_DIE_TEMP(1)>;
806 reg = <PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
807 qcom,hw-settle-time = <200>;
813 reg = <PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
814 qcom,hw-settle-time = <200>;
820 reg = <PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
821 qcom,hw-settle-time = <200>;
827 reg = <PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
828 qcom,hw-settle-time = <200>;
834 reg = <PM8350_ADC7_AMUX_THM5_100K_PU(1)>;
835 qcom,hw-settle-time = <200>;
841 reg = <PM8350_ADC7_GPIO3_100K_PU(1)>;
842 qcom,hw-settle-time = <200>;
854 qcom,hw-settle-time = <200>;
866 qcom,hw-settle-time = <200>;
873 qcom,hw-settle-time = <200>;
881 firmware-name = "qcom/sm8450/adsp.mbn";
886 firmware-name = "qcom/sm8450/cdsp.mbn";
891 firmware-name = "qcom/sm8450/modem.mbn";
896 firmware-name = "qcom/sm8450/slpi.mbn";
908 cd-gpios = <&tlmm 92 GPIO_ACTIVE_HIGH>;
909 pinctrl-names = "default", "sleep";
910 pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
911 pinctrl-1 = <&sdc2_sleep_state &sdc2_card_det_n>;
912 vmmc-supply = <&vreg_l9c_2p96>;
913 vqmmc-supply = <&vreg_l6c_1p8>;
914 no-sdio;
915 no-mmc;
920 compatible = "qcom,sm8450-sndcard";
921 model = "SM8450-HDK";
922 audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
944 wcd-playback-dai-link {
945 link-name = "WCD Playback";
948 sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
952 sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
956 sound-dai = <&q6apm>;
960 wcd-capture-dai-link {
961 link-name = "WCD Capture";
964 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
968 sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>;
972 sound-dai = <&q6apm>;
976 wsa-dai-link {
977 link-name = "WSA Playback";
980 sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
984 sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>;
988 sound-dai = <&q6apm>;
992 va-dai-link {
993 link-name = "VA Capture";
996 sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
1000 sound-dai = <&vamacro 0>;
1004 sound-dai = <&q6apm>;
1012 left_spkr: speaker@0,1 {
1014 reg = <0 1>;
1015 pinctrl-names = "default";
1016 pinctrl-0 = <&spkr_1_sd_n_active>;
1017 powerdown-gpios = <&tlmm 1 GPIO_ACTIVE_LOW>;
1018 #sound-dai-cells = <0>;
1019 sound-name-prefix = "SpkrLeft";
1020 #thermal-sensor-cells = <0>;
1021 vdd-supply = <&vreg_s10b_1p8>;
1027 pinctrl-names = "default";
1028 pinctrl-0 = <&spkr_2_sd_n_active>;
1029 powerdown-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
1030 #sound-dai-cells = <0>;
1031 sound-name-prefix = "SpkrRight";
1032 #thermal-sensor-cells = <0>;
1033 vdd-supply = <&vreg_s10b_1p8>;
1043 qcom,rx-port-mapping = <1 2 3 4 5>;
1053 qcom,tx-port-mapping = <1 1 2 3>;
1058 gpio-reserved-ranges = <28 4>, <36 4>;
1060 lt9611_irq_pin: lt9611-irq-state {
1063 bias-disable;
1066 lt9611_rst_pin: lt9611-rst-state {
1069 output-high;
1072 sdc2_card_det_n: sd-card-det-n-state {
1075 drive-strength = <2>;
1076 bias-pull-up;
1087 reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
1089 vcc-supply = <&vreg_l7b_2p5>;
1090 vcc-max-microamp = <1100000>;
1091 vccq-supply = <&vreg_l9b_1p2>;
1092 vccq-max-microamp = <1200000>;
1093 vdd-hba-supply = <&vreg_l9b_1p2>;
1099 vdda-phy-supply = <&vreg_l5b_0p88>;
1100 vdda-pll-supply = <&vreg_l6b_1p2>;
1109 usb-role-switch;
1113 remote-endpoint = <&pmic_glink_hs_in>;
1117 remote-endpoint = <&usb_1_qmpphy_usb_ss_in>;
1123 vdda-pll-supply = <&vreg_l5b_0p88>;
1124 vdda18-supply = <&vreg_l1c_1p8>;
1125 vdda33-supply = <&vreg_l2b_3p07>;
1131 vdda-phy-supply = <&vreg_l6b_1p2>;
1132 vdda-pll-supply = <&vreg_l1b_0p91>;
1134 orientation-switch;
1138 remote-endpoint = <&mdss_dp0_out>;
1142 remote-endpoint = <&pmic_glink_ss_in>;
1146 remote-endpoint = <&usb_1_dwc3_ss>;
1150 pinctrl-0 = <&dmic01_default>, <&dmic02_default>;
1151 pinctrl-names = "default";
1152 vdd-micb-supply = <&vreg_s10b_1p8>;
1153 qcom,dmic-sample-rate = <600000>;
1159 spkr_1_sd_n_active: spkr-1-sd-n-active-state {
1162 drive-strength = <16>;
1163 bias-disable;
1164 output-low;
1167 spkr_2_sd_n_active: spkr-2-sd-n-active-state {
1170 drive-strength = <16>;
1171 bias-disable;
1172 output-low;
1175 wcd_default: wcd-reset-n-active-state {
1178 drive-strength = <16>;
1179 bias-disable;
1180 output-low;