Lines Matching +full:opp +full:- +full:supply
1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
6 #include "imx8mn-overdrive.dtsi"
16 compatible = "mmc-pwrseq-simple";
17 pinctrl-names = "default";
18 pinctrl-0 = <&pinctrl_usdhc1_gpio>;
19 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
21 clock-names = "ext_clock";
22 post-power-on-delay-ms = <80>;
32 cpu-supply = <&buck2_reg>;
36 cpu-supply = <&buck2_reg>;
40 cpu-supply = <&buck2_reg>;
44 cpu-supply = <&buck2_reg>;
49 opp-1200000000 {
50 opp-microvolt = <950000>;
55 operating-points-v2 = <&ddrc_opp_table>;
57 ddrc_opp_table: opp-table {
58 compatible = "operating-points-v2";
60 opp-25000000 {
61 opp-hz = /bits/ 64 <25000000>;
64 opp-100000000 {
65 opp-hz = /bits/ 64 <100000000>;
68 opp-800000000 {
69 opp-hz = /bits/ 64 <800000000>;
75 pinctrl-names = "default";
76 pinctrl-0 = <&pinctrl_fec1>;
77 phy-mode = "rgmii-id";
78 phy-handle = <ðphy0>;
79 phy-supply = <&buck6_reg>;
80 phy-reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
81 fsl,magic-packet;
85 #address-cells = <1>;
86 #size-cells = <0>;
88 ethphy0: ethernet-phy@0 {
89 compatible = "ethernet-phy-ieee802.3-c22";
96 pinctrl-names = "default";
97 pinctrl-0 = <&pinctrl_flexspi>;
102 #address-cells = <1>;
103 #size-cells = <1>;
104 compatible = "jedec,spi-nor";
105 spi-max-frequency = <80000000>;
106 spi-tx-bus-width = <1>;
107 spi-rx-bus-width = <4>;
112 clock-frequency = <400000>;
113 pinctrl-names = "default";
114 pinctrl-0 = <&pinctrl_i2c1>;
120 pinctrl-names = "default";
121 pinctrl-0 = <&pinctrl_pmic>;
122 interrupt-parent = <&gpio1>;
124 rohm,reset-snvs-powered;
125 #clock-cells = <0>;
127 clock-output-names = "clk-32k-out";
131 regulator-name = "buck1";
132 regulator-min-microvolt = <700000>;
133 regulator-max-microvolt = <1300000>;
134 regulator-boot-on;
135 regulator-always-on;
136 regulator-ramp-delay = <1250>;
140 regulator-name = "buck2";
141 regulator-min-microvolt = <700000>;
142 regulator-max-microvolt = <1300000>;
143 regulator-boot-on;
144 regulator-always-on;
145 regulator-ramp-delay = <1250>;
146 rohm,dvs-run-voltage = <1000000>;
147 rohm,dvs-idle-voltage = <900000>;
152 regulator-name = "buck3";
153 regulator-min-microvolt = <700000>;
154 regulator-max-microvolt = <1350000>;
155 regulator-boot-on;
156 regulator-always-on;
161 regulator-name = "buck4";
162 regulator-min-microvolt = <3000000>;
163 regulator-max-microvolt = <3300000>;
164 regulator-boot-on;
165 regulator-always-on;
170 regulator-name = "buck5";
171 regulator-min-microvolt = <1605000>;
172 regulator-max-microvolt = <1995000>;
173 regulator-boot-on;
174 regulator-always-on;
179 regulator-name = "buck6";
180 regulator-min-microvolt = <800000>;
181 regulator-max-microvolt = <1400000>;
182 regulator-boot-on;
183 regulator-always-on;
187 regulator-name = "ldo1";
188 regulator-min-microvolt = <1600000>;
189 regulator-max-microvolt = <3300000>;
190 regulator-boot-on;
191 regulator-always-on;
195 regulator-name = "ldo2";
196 regulator-min-microvolt = <800000>;
197 regulator-max-microvolt = <900000>;
198 regulator-boot-on;
199 regulator-always-on;
203 regulator-name = "ldo3";
204 regulator-min-microvolt = <1800000>;
205 regulator-max-microvolt = <3300000>;
206 regulator-boot-on;
207 regulator-always-on;
211 regulator-name = "ldo4";
212 regulator-min-microvolt = <900000>;
213 regulator-max-microvolt = <1800000>;
214 regulator-boot-on;
215 regulator-always-on;
219 regulator-name = "ldo6";
220 regulator-min-microvolt = <900000>;
221 regulator-max-microvolt = <1800000>;
222 regulator-boot-on;
223 regulator-always-on;
230 clock-frequency = <400000>;
231 pinctrl-names = "default";
232 pinctrl-0 = <&pinctrl_i2c3>;
238 read-only; /* Manufacturing EEPROM programmed at factory */
249 pinctrl-names = "default";
250 pinctrl-0 = <&pinctrl_uart1>;
251 assigned-clocks = <&clk IMX8MN_CLK_UART1>;
252 assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>;
253 uart-has-rtscts;
257 compatible = "brcm,bcm43438-bt";
258 shutdown-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
259 host-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
260 device-wakeup-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
262 max-speed = <4000000>;
263 clock-names = "extclk";
268 #address-cells = <1>;
269 #size-cells = <0>;
270 pinctrl-names = "default", "state_100mhz", "state_200mhz";
271 pinctrl-0 = <&pinctrl_usdhc1>;
272 pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
273 pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
274 vmmc-supply = <&buck4_reg>;
275 vqmmc-supply = <&buck5_reg>;
276 bus-width = <4>;
277 non-removable;
278 cap-power-off-card;
279 keep-power-in-suspend;
280 mmc-pwrseq = <&usdhc1_pwrseq>;
285 compatible = "brcm,bcm4329-fmac";
286 pinctrl-names = "default";
287 pinctrl-0 = <&pinctrl_wlan>;
288 interrupt-parent = <&gpio2>;
290 interrupt-names = "host-wake";
295 pinctrl-names = "default", "state_100mhz", "state_200mhz";
296 pinctrl-0 = <&pinctrl_usdhc3>;
297 pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
298 pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
299 bus-width = <8>;
300 non-removable;
305 pinctrl-names = "default";
306 pinctrl-0 = <&pinctrl_wdog>;
307 fsl,ext-reset-output;
393 pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
404 pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
431 pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
447 pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {