Lines Matching +full:neg +full:- +full:edge
1 /* SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause) */
3 * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
7 /dts-v1/;
10 #include "stm32mp15xx-osd32.dtsi"
11 #include "stm32mp15xxac-pinctrl.dtsi"
13 #include <dt-bindings/gpio/gpio.h>
14 #include <dt-bindings/pwm/pwm.h>
17 model = "Linux Automation MC-1 board";
18 compatible = "lxa,stm32mp157c-mc1", "oct,stm32mp15xx-osd32", "st,stm32mp157";
28 compatible = "pwm-backlight";
30 brightness-levels = <0 31 63 95 127 159 191 223 255>;
31 default-brightness-level = <7>;
32 power-supply = <®_5v2>; /* 3V3_BACKLIGHT */
36 stdout-path = &uart4;
39 led-controller-0 {
40 compatible = "gpio-leds";
42 led-0 {
45 linux,default-trigger = "heartbeat";
49 led-controller-1 {
50 compatible = "pwm-leds";
52 /* led-1 to led-3 are part of a single RGB led */
53 led-1 {
56 max-brightness = <255>;
57 active-low;
60 led-2 {
63 max-brightness = <255>;
64 active-low;
67 led-3 {
70 max-brightness = <255>;
71 active-low;
78 enable-gpios = <&gpiod 4 GPIO_ACTIVE_HIGH>;
79 power-supply = <®_3v3>;
83 remote-endpoint = <<dc_ep0_out>;
89 compatible = "regulator-fixed";
90 regulator-name = "3V3";
91 regulator-min-microvolt = <3300000>;
92 regulator-max-microvolt = <3300000>;
93 regulator-always-on;
94 vin-supply = <&v3v3>;
99 compatible = "regulator-fixed";
100 regulator-name = "5V2";
101 regulator-min-microvolt = <5200000>;
102 regulator-max-microvolt = <5200000>;
103 regulator-always-on;
108 pinctrl-names = "default", "sleep";
109 pinctrl-0 = <ðernet0_rgmii_pins_b>;
110 pinctrl-1 = <ðernet0_rgmii_sleep_pins_b>;
111 phy-mode = "rgmii-id";
112 phy-handle = <ðphy>;
116 compatible = "snps,dwmac-mdio";
117 #address-cells = <1>;
118 #size-cells = <0>;
120 ethphy: ethernet-phy@3 { /* KSZ9031RN */
122 reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
123 interrupt-parent = <&gpioa>;
125 reset-assert-us = <10000>;
126 reset-deassert-us = <300>;
127 micrel,force-master;
133 gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", "",
138 pinctrl-names = "default", "sleep";
139 pinctrl-0 = <&i2c5_pins_b>;
140 pinctrl-1 = <&i2c5_sleep_pins_b>;
141 clock-frequency = <400000>;
145 compatible = "edt,edt-ft5x06";
146 interrupt-parent = <&gpiod>;
148 vcc-supply = <®_3v3>;
150 reset-gpios = <&gpiof 8 GPIO_ACTIVE_LOW>; /* TOUCH_RESET# */
151 touchscreen-size-x = <1792>;
152 touchscreen-size-y = <1024>;
153 wakeup-source;
158 pinctrl-names = "default", "sleep";
159 pinctrl-0 = <<dc_pins_c>;
160 pinctrl-1 = <<dc_sleep_pins_c>;
165 remote-endpoint = <&panel_input>;
172 buck4-supply = <®_5v2>; /* VIN */
173 ldo2-supply = <®_5v2>; /* PMIC_LDO25IN */
174 ldo5-supply = <®_5v2>; /* PMIC_LDO25IN */
175 boost-supply = <®_5v2>; /* PMIC_BSTIN */
176 pwr_sw2-supply = <&bst_out>; /* PMIC_SWIN */
181 pinctrl-names = "default", "opendrain", "sleep";
182 pinctrl-0 = <&sdmmc1_b4_pins_a>;
183 pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
184 pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
185 bus-width = <4>;
186 cd-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
187 disable-wp;
188 no-1-8-v;
189 st,neg-edge;
190 vmmc-supply = <®_3v3>;
196 * board lacks external pull-ups on SDMMC lines. Class 10 SD refuses to
197 * work, thus enable internal pull-ups.
200 /delete-property/ bias-disable;
201 bias-pull-up;
204 /delete-property/ bias-disable;
205 bias-pull-up;
210 pinctrl-names = "default", "opendrain", "sleep";
211 pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
212 pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
213 pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
214 bus-width = <8>;
215 mmc-ddr-3_3v;
216 no-1-8-v;
217 no-sd;
218 no-sdio;
219 non-removable;
220 st,neg-edge;
221 vmmc-supply = <®_3v3>;
229 pinctrl-names = "default", "sleep";
230 pinctrl-0 = <&pwm3_pins_b>;
231 pinctrl-1 = <&pwm3_sleep_pins_b>;
240 pinctrl-names = "default", "sleep";
241 pinctrl-0 = <&pwm5_pins_b>;
242 pinctrl-1 = <&pwm5_sleep_pins_b>;
248 pinctrl-names = "default";
249 pinctrl-0 = <&uart4_pins_a>;
250 /delete-property/dmas;
251 /delete-property/dma-names;