Lines Matching +full:re +full:- +full:routed

1 // SPDX-License-Identifier: GPL-2.0
6 /dts-v1/;
7 #include <dt-bindings/interrupt-controller/irq.h>
8 #include <dt-bindings/gpio/gpio.h>
9 #include "ste-nomadik-stn8815.dtsi"
13 	compatible = "st,nomadik-nhk-15";
22 		stmpe-i2c0 = &stmpe0;
23 		stmpe-i2c1 = &stmpe1;
71 		disable-sxtalo;
72 		disable-mxtalo;
75 	/* This is where the interrupt is routed on the NHK-15 debug board */
76 	external-bus@34000000 {
77 		compatible = "simple-bus";
79 		#address-cells = <1>;
80 		#size-cells = <1>;
85 			reg-io-width = <2>;
86 			reset-gpios = <&stmpe_gpio44 10 GPIO_ACTIVE_HIGH>;
87 			interrupt-parent = <&stmpe_gpio44>;
95 			compatible = "st,lis3lv02dl-accel";
96 			interrupt-parent = <&gpio2>;
98 			pinctrl-0 = <&lis3lv02dl_nhk_mode>;
99 			pinctrl-names = "default";
102 		stmpe0: port-expander@43 {
105 			reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; // GPIO77
107 			interrupt-parent = <&gpio2>;
108 			wakeup-source;
109 			pinctrl-names = "default";
110 			pinctrl-0 = <&stmpe2401_1_nhk_mode>;
112 				compatible = "st,stmpe-gpio";
113 				gpio-controller;
114 				#gpio-cells = <2>;
115 				interrupt-controller;
116 				#interrupt-cells = <2>;
118 				st,norequest-mask = <0xf0f002>;
120 			keyboard-controller {
121 				compatible = "st,stmpe-keypad";
122 				debounce-interval = <64>;
123 				st,scan-count = <8>;
124 				st,no-autorepeat;
125 				keypad,num-rows = <8>;
126 				keypad,num-columns = <8>;
143 				compatible = "st,stmpe-pwm";
144 				#pwm-cells = <2>;
147 		stmpe1: port-expander@44 {
150 			reset-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; // GPIO79
152 			interrupt-parent = <&gpio2>;
153 			wakeup-source;
154 			pinctrl-names = "default";
155 			pinctrl-0 = <&stmpe2401_2_nhk_mode>;
157 				compatible = "st,stmpe-gpio";
158 				gpio-controller;
159 				#gpio-cells = <2>;
160 				interrupt-controller;
161 				#interrupt-cells = <2>;
166 				mmcsd-hog {
167 					gpio-hog;
169 					output-low;
170 					line-name = "SATA EN";
179 			pinctrl-names = "default";
180 			pinctrl-0 = <&clcd_24bit_mux>;
183 					remote-endpoint = <&nomadik_clcd_panel>;
184 					arm,pl11x,tft-r0g0b0-pads = <16 8 0>;
192 			pinctrl-names = "default";
193 			pinctrl-0 = <&uart0_nhk_mode>;
197 			cd-gpios = <&stmpe_gpio44 7 GPIO_ACTIVE_LOW>;
198 			wp-gpios = <&stmpe_gpio44 18 GPIO_ACTIVE_HIGH>;
203 		compatible = "spi-gpio";
204 		#address-cells = <1>;
205 		#size-cells = <0>;
208 		 * As we're dealing with 3wire SPI, we only define SCK
211 		sck-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
212 		mosi-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
213 		cs-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
214 		num-chipselects = <1>;
218 		 * WVGA (800x480): 4.3" TPG110 TDO43MTEA2 24-bit RGB
228 			spi-3wire;
230 			spi-max-frequency = <3000000>;
232 			width-mm = <116>;
233 			height-mm = <87>;
234 			grestb-gpios = <&stmpe_gpio44 5 GPIO_ACTIVE_LOW>;
239 					remote-endpoint = <&nomadik_clcd>;
246 		compatible = "pwm-backlight";
248 		pwm-names = "backlight";
249 		brightness-levels = <
262 		default-brightness-level = <100>;