Lines Matching +full:board +full:- +full:related
1 // SPDX-License-Identifier: GPL-2.0
2 #include <dt-bindings/input/input.h>
3 #include <dt-bindings/thermal/thermal.h>
5 #include "tegra30-cpu-opp.dtsi"
6 #include "tegra30-cpu-opp-microvolt.dtsi"
15 * related dts file need to be chosen like for Cardhu fab version A02,
16 * use tegra30-cardhu-a02.dts, Cardhu fab version A04 and later, use
17 * tegra30-cardhu-a04.dts.
18 * The identification of board is done in two ways, by looking the sticker
19 * on PCB and by reading board id eeprom.
20 * The sticker will have number like 600-81291-1000-002 C.3. In this 4th
22 * The (downstream internal) U-Boot of Cardhu display the board-id as
32 model = "NVIDIA Tegra30 Cardhu evaluation board";
43 stdout-path = "serial0:115200n8";
54 avdd-pexb-supply = <&ldo1_reg>;
55 vdd-pexb-supply = <&ldo1_reg>;
56 avdd-pex-pll-supply = <&ldo1_reg>;
57 hvdd-pex-supply = <&pex_hvdd_3v3_reg>;
58 vddio-pex-ctl-supply = <&sys_3v3_reg>;
59 avdd-plle-supply = <&ldo2_reg>;
62 nvidia,num-lanes = <4>;
66 nvidia,num-lanes = <1>;
71 nvidia,num-lanes = <1>;
86 pinctrl-names = "default";
87 pinctrl-0 = <&state_default>;
153 nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
155 nvidia,pull-down-strength = <46>;
156 nvidia,pull-up-strength = <42>;
157 nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FAST>;
158 nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FAST>;
173 /delete-property/ dmas;
174 /delete-property/ dma-names;
179 compatible = "nvidia,tegra30-hsuart";
180 reset-names = "serial";
181 /delete-property/ reg-shift;
191 clock-frequency = <100000>;
196 clock-frequency = <100000>;
201 clock-frequency = <100000>;
207 interrupt-parent = <&gpio>;
213 #address-cells = <1>;
214 #size-cells = <0>;
216 reset-gpios = <&gpio TEGRA_GPIO(BB, 0) GPIO_ACTIVE_LOW>;
222 clock-frequency = <100000>;
227 clock-frequency = <100000>;
232 interrupt-parent = <&gpio>;
235 gpio-controller;
236 #gpio-cells = <2>;
238 micdet-cfg = <0>;
239 micdet-delay = <100>;
240 gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
248 #interrupt-cells = <2>;
249 interrupt-controller;
250 wakeup-source;
252 ti,system-power-controller;
254 #gpio-cells = <2>;
255 gpio-controller;
257 vcc1-supply = <&vdd_ac_bat_reg>;
258 vcc2-supply = <&vdd_ac_bat_reg>;
259 vcc3-supply = <&vio_reg>;
260 vcc4-supply = <&vdd_5v0_reg>;
261 vcc5-supply = <&vdd_ac_bat_reg>;
262 vcc6-supply = <&vdd2_reg>;
263 vcc7-supply = <&vdd_ac_bat_reg>;
264 vccio-supply = <&vdd_ac_bat_reg>;
268 regulator-name = "vddio_ddr_1v2";
269 regulator-min-microvolt = <1200000>;
270 regulator-max-microvolt = <1200000>;
271 regulator-always-on;
275 regulator-name = "vdd_1v5_gen";
276 regulator-min-microvolt = <1500000>;
277 regulator-max-microvolt = <1500000>;
278 regulator-always-on;
282 regulator-name = "vdd_cpu,vdd_sys";
283 regulator-min-microvolt = <800000>;
284 regulator-max-microvolt = <1250000>;
285 regulator-coupled-with = <&vdd_core>;
286 regulator-coupled-max-spread = <300000>;
287 regulator-max-step-microvolt = <100000>;
288 regulator-always-on;
290 nvidia,tegra-cpu-regulator;
294 regulator-name = "vdd_1v8_gen";
295 regulator-min-microvolt = <1800000>;
296 regulator-max-microvolt = <1800000>;
297 regulator-always-on;
301 regulator-name = "vdd_pexa,vdd_pexb";
302 regulator-min-microvolt = <1050000>;
303 regulator-max-microvolt = <1050000>;
307 regulator-name = "vdd_sata,avdd_plle";
308 regulator-min-microvolt = <1050000>;
309 regulator-max-microvolt = <1050000>;
315 regulator-name = "vdd_rtc";
316 regulator-min-microvolt = <1200000>;
317 regulator-max-microvolt = <1200000>;
318 regulator-always-on;
322 regulator-name = "vddio_sdmmc,avdd_vdac";
323 regulator-min-microvolt = <3300000>;
324 regulator-max-microvolt = <3300000>;
325 regulator-always-on;
329 regulator-name = "avdd_dsi_csi,pwrdet_mipi";
330 regulator-min-microvolt = <1200000>;
331 regulator-max-microvolt = <1200000>;
335 regulator-name = "vdd_pllm,x,u,a_p_c_s";
336 regulator-min-microvolt = <1200000>;
337 regulator-max-microvolt = <1200000>;
338 regulator-always-on;
342 regulator-name = "vdd_ddr_hs";
343 regulator-min-microvolt = <1000000>;
344 regulator-max-microvolt = <1000000>;
345 regulator-always-on;
350 nct1008: temperature-sensor@4c {
353 vcc-supply = <&sys_3v3_reg>;
354 interrupt-parent = <&gpio>;
356 #thermal-sensor-cells = <1>;
363 regulator-name = "tps62361-vout";
364 regulator-min-microvolt = <500000>;
365 regulator-max-microvolt = <1500000>;
366 regulator-coupled-with = <&vddctrl_reg>;
367 regulator-coupled-max-spread = <300000>;
368 regulator-max-step-microvolt = <100000>;
369 regulator-boot-on;
370 regulator-always-on;
371 ti,vsel0-state-high;
372 ti,vsel1-state-high;
374 nvidia,tegra-core-regulator;
380 spi-max-frequency = <25000000>;
383 compatible = "winbond,w25q32", "jedec,spi-nor";
385 spi-max-frequency = <20000000>;
391 nvidia,invert-interrupt;
392 nvidia,suspend-mode = <1>;
393 nvidia,cpu-pwr-good-time = <2000>;
394 nvidia,cpu-pwr-off-time = <200>;
395 nvidia,core-pwr-good-time = <3845 3845>;
396 nvidia,core-pwr-off-time = <0>;
397 nvidia,core-power-req-active-high;
398 nvidia,sys-clock-req-active-high;
399 core-supply = <&vdd_core>;
410 cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
411 wp-gpios = <&gpio TEGRA_GPIO(T, 3) GPIO_ACTIVE_HIGH>;
412 power-gpios = <&gpio TEGRA_GPIO(D, 7) GPIO_ACTIVE_HIGH>;
413 bus-width = <4>;
418 bus-width = <8>;
419 non-removable;
426 usb-phy@7d008000 {
427 vbus-supply = <&usb3_vbus_reg>;
432 compatible = "pwm-backlight";
434 enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
435 power-supply = <&vdd_bl_reg>;
438 brightness-levels = <0 4 8 16 32 64 128 255>;
439 default-brightness-level = <6>;
442 clk32k_in: clock-32k {
443 compatible = "fixed-clock";
444 clock-frequency = <32768>;
445 #clock-cells = <0>;
450 cpu-supply = <&vddctrl_reg>;
451 operating-points-v2 = <&cpu0_opp_table>;
452 #cooling-cells = <2>;
456 cpu-supply = <&vddctrl_reg>;
457 operating-points-v2 = <&cpu0_opp_table>;
458 #cooling-cells = <2>;
462 cpu-supply = <&vddctrl_reg>;
463 operating-points-v2 = <&cpu0_opp_table>;
464 #cooling-cells = <2>;
468 cpu-supply = <&vddctrl_reg>;
469 operating-points-v2 = <&cpu0_opp_table>;
470 #cooling-cells = <2>;
474 gpio-keys {
475 compatible = "gpio-keys";
477 key-power {
479 interrupt-parent = <&pmic>;
482 debounce-interval = <100>;
483 wakeup-source;
486 key-volume-down {
490 debounce-interval = <10>;
493 key-volume-up {
497 debounce-interval = <10>;
503 ddc-i2c-bus = <&panelddc>;
505 power-supply = <&vdd_pnl1_reg>;
506 enable-gpios = <&gpio TEGRA_GPIO(L, 2) GPIO_ACTIVE_HIGH>;
511 vdd_ac_bat_reg: regulator-acbat {
512 compatible = "regulator-fixed";
513 regulator-name = "vdd_ac_bat";
514 regulator-min-microvolt = <5000000>;
515 regulator-max-microvolt = <5000000>;
516 regulator-always-on;
519 cam_1v8_reg: regulator-cam {
520 compatible = "regulator-fixed";
521 regulator-name = "cam_1v8";
522 regulator-min-microvolt = <1800000>;
523 regulator-max-microvolt = <1800000>;
524 enable-active-high;
526 vin-supply = <&vio_reg>;
529 cp_5v_reg: regulator-5v0cp {
530 compatible = "regulator-fixed";
531 regulator-name = "cp_5v";
532 regulator-min-microvolt = <5000000>;
533 regulator-max-microvolt = <5000000>;
534 regulator-boot-on;
535 regulator-always-on;
536 enable-active-high;
540 emmc_3v3_reg: regulator-emmc {
541 compatible = "regulator-fixed";
542 regulator-name = "emmc_3v3";
543 regulator-min-microvolt = <3300000>;
544 regulator-max-microvolt = <3300000>;
545 regulator-always-on;
546 regulator-boot-on;
547 enable-active-high;
549 vin-supply = <&sys_3v3_reg>;
552 modem_3v3_reg: regulator-modem {
553 compatible = "regulator-fixed";
554 regulator-name = "modem_3v3";
555 regulator-min-microvolt = <3300000>;
556 regulator-max-microvolt = <3300000>;
557 enable-active-high;
561 pex_hvdd_3v3_reg: regulator-pex {
562 compatible = "regulator-fixed";
563 regulator-name = "pex_hvdd_3v3";
564 regulator-min-microvolt = <3300000>;
565 regulator-max-microvolt = <3300000>;
566 enable-active-high;
568 vin-supply = <&sys_3v3_reg>;
571 vdd_cam1_ldo_reg: regulator-cam1 {
572 compatible = "regulator-fixed";
573 regulator-name = "vdd_cam1_ldo";
574 regulator-min-microvolt = <2800000>;
575 regulator-max-microvolt = <2800000>;
576 enable-active-high;
578 vin-supply = <&sys_3v3_reg>;
581 vdd_cam2_ldo_reg: regulator-cam2 {
582 compatible = "regulator-fixed";
583 regulator-name = "vdd_cam2_ldo";
584 regulator-min-microvolt = <2800000>;
585 regulator-max-microvolt = <2800000>;
586 enable-active-high;
588 vin-supply = <&sys_3v3_reg>;
591 vdd_cam3_ldo_reg: regulator-cam3 {
592 compatible = "regulator-fixed";
593 regulator-name = "vdd_cam3_ldo";
594 regulator-min-microvolt = <3300000>;
595 regulator-max-microvolt = <3300000>;
596 enable-active-high;
598 vin-supply = <&sys_3v3_reg>;
601 vdd_com_reg: regulator-com {
602 compatible = "regulator-fixed";
603 regulator-name = "vdd_com";
604 regulator-min-microvolt = <3300000>;
605 regulator-max-microvolt = <3300000>;
606 regulator-always-on;
607 regulator-boot-on;
608 enable-active-high;
610 vin-supply = <&sys_3v3_reg>;
613 vdd_fuse_3v3_reg: regulator-fuse {
614 compatible = "regulator-fixed";
615 regulator-name = "vdd_fuse_3v3";
616 regulator-min-microvolt = <3300000>;
617 regulator-max-microvolt = <3300000>;
618 enable-active-high;
620 vin-supply = <&sys_3v3_reg>;
623 vdd_pnl1_reg: regulator-pnl1 {
624 compatible = "regulator-fixed";
625 regulator-name = "vdd_pnl1";
626 regulator-min-microvolt = <3300000>;
627 regulator-max-microvolt = <3300000>;
628 regulator-always-on;
629 regulator-boot-on;
630 enable-active-high;
632 vin-supply = <&sys_3v3_reg>;
635 vdd_vid_reg: regulator-vid {
636 compatible = "regulator-fixed";
637 regulator-name = "vddio_vid";
638 regulator-min-microvolt = <5000000>;
639 regulator-max-microvolt = <5000000>;
640 enable-active-high;
642 gpio-open-drain;
643 vin-supply = <&vdd_5v0_reg>;
647 compatible = "nvidia,tegra-audio-wm8903-cardhu",
648 "nvidia,tegra-audio-wm8903";
651 nvidia,audio-routing =
661 nvidia,i2s-controller = <&tegra_i2s1>;
662 nvidia,audio-codec = <&wm8903>;
664 nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
665 nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2)
671 clock-names = "pll_a", "pll_a_out0", "mclk";
673 assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
676 assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
680 thermal-zones {
681 cpu-thermal {
682 polling-delay-passive = <1000>; /* milliseconds */
683 polling-delay = <5000>; /* milliseconds */
685 thermal-sensors = <&nct1008 1>;
688 trip0: cpu-alert0 {
695 trip1: cpu-crit {
703 cooling-maps {
706 cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,