Lines Matching +full:connect +full:- +full:gpios

1 // SPDX-License-Identifier: GPL-2.0
3  * at91-wb50n.dtsi - Device Tree include file for wb50n cpu module
12 	model = "Laird Workgroup Bridge 50N - Atmel SAMA5D";
17 		stdout-path = "serial0:115200n8";
38 	clock-frequency = <32768>;
42 	clock-frequency = <12000000>;
46 	atmel,osc-bypass;
50 	pinctrl-names = "default";
51 	pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
52 	cd-gpios = <&pioC 26 GPIO_ACTIVE_LOW>;
55 		bus-width = <4>;
60 	pinctrl-names = "default";
61 	pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
65 		atheros,board-id = "SD32";
67 		bus-width = <4>;
72 	phy-mode = "rmii";
81 	atmel,use-dma-rx;
82 	atmel,use-dma-tx;
83 	pinctrl-names = "default";
84 	pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts_cts>;
89 	atmel,use-dma-rx;
90 	atmel,use-dma-tx;
91 	pinctrl-names = "default";
92 	pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
93 	dtr-gpios = <&pioD 13 GPIO_ACTIVE_LOW>;
94 	dsr-gpios = <&pioD 11 GPIO_ACTIVE_LOW>;
95 	dcd-gpios = <&pioD 7 GPIO_ACTIVE_LOW>;
96 	rng-gpios = <&pioD 8 GPIO_ACTIVE_LOW>;
99 /* USART3 is direct-connect to the Bluetooth UART on the radio SIP */
101 	atmel,use-dma-rx;
102 	atmel,use-dma-tx;
103 	pinctrl-names = "default";
104 	pinctrl-0 = <&pinctrl_usart3 &pinctrl_usart3_rts_cts>;
109 	cs-gpios = <&pioC 25 0>, <0>, <0>, <0>;
113 	pinctrl-0 = <&pinctrl_ebi_nand_addr>;
114 	pinctrl-names = "default";
124 		nand-bus-width = <8>;
125 		nand-ecc-mode = "hw";
126 		nand-ecc-strength = <8>;
127 		nand-ecc-step-size = <512>;
128 		nand-on-flash-bbt;
132 			compatible = "fixed-partitions";
133 			#address-cells = <1>;
134 			#size-cells = <1>;
142 				label = "u-boot";
147 				label = "u-boot-env";
152 				label = "u-boot-env";
156 			kernel-a@e0000 {
157 				label = "kernel-a";
161 			kernel-b@5e0000 {
162 				label = "kernel-b";
166 			rootfs-a@ae0000 {
167 				label = "rootfs-a";
171 			rootfs-b@3ae0000 {
172 				label = "rootfs-b";
185 	atmel,vbus-gpio = <&pioB 13 GPIO_ACTIVE_LOW>;
186 	pinctrl-names = "default";
187 	pinctrl-0 = <&pinctrl_usba_vbus>;
191 	num-ports = <3>;
192 	atmel,vbus-gpio = <&pioA 2 GPIO_ACTIVE_LOW>;
193 	atmel,oc-gpio = <&pioA 4 GPIO_ACTIVE_LOW>;