Lines Matching +full:gpio +full:- +full:delay

1 // SPDX-License-Identifier: GPL-2.0
6 /dts-v1/;
9 #include <dt-bindings/input/input.h>
14 	#address-cells = <1>;
15 	#size-cells = <1>;
24 		stdout-path = &uart0;
28 		compatible = "gpio-keys";
30 		button-setup {
31 			debounce-interval = <100>;
32 			wakeup-source;
41 		compatible = "gpio-leds";
42 		led-green-info {
45 			default-state = "on";
46 			linux,default-trigger = "heartbeat";
48 		led-green-usb {
51 			default-state = "off";
52 			linux,default-trigger = "usb-host";
57 		compatible = "virtual,mdio-gpio";
61 		#address-cells = <1>;
62 		#size-cells = <0>;
65 		phy0: ethernet-phy@1 {
71 		compatible = "spi-gpio";
72 		#address-cells = <1>;
73 		#size-cells = <0>;
75 		sck-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
76 		miso-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
77 		mosi-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
78 		cs-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
79 		num-chipselects = <1>;
85 			spi-max-frequency = <2500000>;
86 			gpio-controller;
87 			#gpio-cells = <2>;
90 				#address-cells = <1>;
91 				#size-cells = <0>;
113 					phy-mode = "rgmii";
114 					fixed-link {
116 						full-duplex;
128 			pinctrl-names = "enabled", "disabled";
129 			pinctrl-0 = <&pflash_default_pins>;
130 			pinctrl-1 = <&pflash_disabled_pins>;
135 				compatible = "redboot-fis";
137 				fis-index-block = <0x1fc>;
149 				gpio0_default_pins: pinctrl-gpio0 {
160 				gpio1_default_pins: pinctrl-gpio1 {
167 				 * These GPIO groups will be mapped in over some
171 				pflash_disabled_pins: pinctrl-pflash-disabled {
178 				pinctrl-gmii {
186 						skew-delay = <0>;
190 						skew-delay = <15>;
194 						skew-delay = <7>;
198 						skew-delay = <10>;
202 						skew-delay = <7>;
206 						skew-delay = <8>;
210 						skew-delay = <7>;
214 						skew-delay = <5>;
226 						skew-delay = <7>;
231 						drive-strength = <16>;
238 			cortina,gemini-ata-muxmode = <0>;
239 			cortina,gemini-enable-sata-bridge;
243 		gpio0: gpio@4d000000 {
244 			pinctrl-names = "default";
245 			pinctrl-0 = <&gpio0_default_pins>;
248 		gpio1: gpio@4e000000 {
249 			pinctrl-names = "default";
250 			pinctrl-0 = <&gpio1_default_pins>;
260 			ethernet-port@0 {
261 				phy-mode = "rgmii";
262 				phy-handle = <&phy0>;
264 			ethernet-port@1 {
265 				phy-mode = "rgmii";
266 				fixed-link {
268 					full-duplex;