Lines Matching +full:pll +full:- +full:reset +full:- +full:mode
11 Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or
12 super-speed USB. Other lanes are for various types of low-speed, full-speed
13 or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller
14 contains a software-configurable mux that sits between the I/O controller
17 In addition to per-lane configuration, USB 3.0 ports may require additional
18 settings on a per-board basis.
20 Pads will be represented as children of the top-level XUSB pad controller
23 PHY bindings, as described by the phy-bindings.txt file in this directory.
34 --------------------
35 - compatible: Must be:
36 - Tegra124: "nvidia,tegra124-xusb-padctl"
37 - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
38 - Tegra210: "nvidia,tegra210-xusb-padctl"
39 - Tegra186: "nvidia,tegra186-xusb-padctl"
40 - Tegra194: "nvidia,tegra194-xusb-padctl"
41 - reg: Physical base address and length of the controller's registers.
42 - resets: Must contain an entry for each entry in reset-names.
43 - reset-names: Must include the following entries:
44 - "padctl"
47 - avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V.
48 - avdd-pll-erefe-supply: PLLE reference PLL power supply. Must supply 1.05 V.
49 - avdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V.
50 - hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 3.3 V.
53 - avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V.
54 - avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V.
55 - dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V.
56 - hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V.
57 - nvidia,pmc: phandle and specifier referring to the Tegra210 PMC node.
60 - avdd-pll-erefeut-supply: UPHY brick and reference clock as well as UTMI PHY
62 - avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
64 - vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
65 - vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.
68 - avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
70 - vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
90 ---------
93 - clocks: Must contain an entry for each entry in clock-names.
94 - clock-names: Must contain the following entries:
95 - "trk": phandle and specifier referring to the USB2 tracking clock
98 ---------
101 - clocks: Must contain an entry for each entry in clock-names.
102 - clock-names: Must contain the following entries:
103 - "trk": phandle and specifier referring to the HSIC tracking clock
106 ---------
109 - clocks: Must contain an entry for each entry in clock-names.
110 - clock-names: Must contain the following entries:
111 - "pll": phandle and specifier referring to the PLLE
112 - resets: Must contain an entry for each entry in reset-names.
113 - reset-names: Must contain the following entries:
114 - "phy": reset for the PCIe UPHY block
117 ---------
120 - resets: Must contain an entry for each entry in reset-names.
121 - reset-names: Must contain the following entries:
122 - "phy": reset for the SATA UPHY block
132 --------------------
133 - status: Defines the operation status of the PHY. Valid values are:
134 - "disabled": the PHY is disabled
135 - "okay": the PHY is enabled
136 - #phy-cells: Should be 0. Since each lane represents a single PHY, there is
138 - nvidia,function: The output function of the PHY. See below for a list of
142 - usb2: usb2-0, usb2-1, usb2-2
143 - functions: "snps", "xusb", "uart"
144 - ulpi: ulpi-0
145 - functions: "snps", "xusb"
146 - hsic: hsic-0, hsic-1
147 - functions: "snps", "xusb"
148 - pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4
149 - functions: "pcie", "usb3-ss"
150 - sata: sata-0
151 - functions: "usb3-ss", "sata"
154 - usb2: usb2-0, usb2-1, usb2-2, usb2-3
155 - functions: "snps", "xusb", "uart"
156 - hsic: hsic-0, hsic-1
157 - functions: "snps", "xusb"
158 - pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, pcie-5, pcie-6
159 - functions: "pcie-x1", "usb3-ss", "pcie-x4"
160 - sata: sata-0
161 - functions: "usb3-ss", "sata"
164 - usb2: usb2-0, usb2-1, usb2-2, usb2-3
165 - functions: "xusb"
166 - usb3: usb3-0, usb3-1, usb3-2, usb3-3
167 - functions: "xusb"
173 by the XUSB pad controller. Per-port configuration is only required for USB.
176 -----------
179 - status: Defines the operation status of the port. Valid values are:
180 - "disabled": the port is disabled
181 - "okay": the port is enabled
182 - mode: A string that determines the mode in which to run the port. Valid
184 - "host": for USB host mode
185 - "device": for USB device mode
186 - "otg": for USB OTG mode
189 - usb-role-switch: Boolean property to indicate that the port support OTG or
190 peripheral mode. If present, the port supports switching between USB host
192 See usb/usb-conn-gpio.txt.
195 - nvidia,internal: A boolean property whose presence determines that a port
198 - vbus-supply: phandle to a regulator supplying the VBUS voltage.
201 -----------
204 - status: Defines the operation status of the port. Valid values are:
205 - "disabled": the port is disabled
206 - "okay": the port is enabled
207 - nvidia,internal: A boolean property whose presence determines that a port
210 - vbus-supply: phandle to a regulator supplying the VBUS voltage.
213 -----------
216 - status: Defines the operation status of the port. Valid values are:
217 - "disabled": the port is disabled
218 - "okay": the port is enabled
221 - vbus-supply: phandle to a regulator supplying the VBUS voltage.
223 Super-speed USB ports:
224 ----------------------
227 - status: Defines the operation status of the port. Valid values are:
228 - "disabled": the port is disabled
229 - "okay": the port is enabled
230 - nvidia,usb2-companion: A single cell that specifies the physical port number
231 to map this super-speed USB port to. The range of valid port numbers varies
233 - 0-2: for Tegra124 and Tegra132
234 - 0-3: for Tegra210
237 - nvidia,internal: A boolean property whose presence determines that a port
241 - maximum-speed: Only for Tegra194. A string property that specifies maximum
243 - "super-speed-plus": default, the usb3 port supports USB 3.1 Gen 2 speed.
244 - "super-speed": the usb3 port supports USB 3.1 Gen 1 speed only.
248 - 3x USB2: usb2-0, usb2-1, usb2-2
249 - 1x ULPI: ulpi-0
250 - 2x HSIC: hsic-0, hsic-1
251 - 2x super-speed USB: usb3-0, usb3-1
254 - 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3
255 - 2x HSIC: hsic-0, hsic-1
256 - 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3
259 - 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3
260 - 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3
266 ----------------------
272 compatible = "nvidia,tegra124-xusb-padctl";
274 compatible = "nvidia,tegra132-xusb-padctl",
275 "nvidia,tegra124-xusb-padctl";
278 reset-names = "padctl";
285 usb2-0 {
287 #phy-cells = <0>;
290 usb2-1 {
292 #phy-cells = <0>;
295 usb2-2 {
297 #phy-cells = <0>;
306 ulpi-0 {
308 #phy-cells = <0>;
317 hsic-0 {
319 #phy-cells = <0>;
322 hsic-1 {
324 #phy-cells = <0>;
333 pcie-0 {
335 #phy-cells = <0>;
338 pcie-1 {
340 #phy-cells = <0>;
343 pcie-2 {
345 #phy-cells = <0>;
348 pcie-3 {
350 #phy-cells = <0>;
353 pcie-4 {
355 #phy-cells = <0>;
364 sata-0 {
366 #phy-cells = <0>;
373 usb2-0 {
377 usb2-1 {
381 usb2-2 {
385 ulpi-0 {
389 hsic-0 {
393 hsic-1 {
397 usb3-0 {
401 usb3-1 {
417 usb2-0 {
422 usb2-1 {
427 usb2-2 {
438 pcie-0 {
439 nvidia,function = "usb3-ss";
443 pcie-2 {
448 pcie-4 {
459 sata-0 {
469 usb2-0 {
471 mode = "otg";
475 usb2-1 {
477 mode = "host";
481 usb2-2 {
483 mode = "host";
485 vbus-supply = <&vdd_usb3_vbus>;
488 usb3-0 {
496 ---------
501 compatible = "nvidia,tegra210-xusb-padctl";
504 reset-names = "padctl";
511 clock-names = "trk";
515 usb2-0 {
517 #phy-cells = <0>;
520 usb2-1 {
522 #phy-cells = <0>;
525 usb2-2 {
527 #phy-cells = <0>;
530 usb2-3 {
532 #phy-cells = <0>;
539 clock-names = "trk";
543 hsic-0 {
545 #phy-cells = <0>;
548 hsic-1 {
550 #phy-cells = <0>;
557 clock-names = "pll";
559 reset-names = "phy";
563 pcie-0 {
565 #phy-cells = <0>;
568 pcie-1 {
570 #phy-cells = <0>;
573 pcie-2 {
575 #phy-cells = <0>;
578 pcie-3 {
580 #phy-cells = <0>;
583 pcie-4 {
585 #phy-cells = <0>;
588 pcie-5 {
590 #phy-cells = <0>;
593 pcie-6 {
595 #phy-cells = <0>;
602 clock-names = "pll";
604 reset-names = "phy";
608 sata-0 {
610 #phy-cells = <0>;
617 usb2-0 {
621 usb2-1 {
625 usb2-2 {
629 usb2-3 {
633 hsic-0 {
637 hsic-1 {
641 usb3-0 {
645 usb3-1 {
649 usb3-2 {
653 usb3-3 {
669 usb2-0 {
674 usb2-1 {
679 usb2-2 {
684 usb2-3 {
695 pcie-0 {
696 nvidia,function = "pcie-x1";
700 pcie-1 {
701 nvidia,function = "pcie-x4";
705 pcie-2 {
706 nvidia,function = "pcie-x4";
710 pcie-3 {
711 nvidia,function = "pcie-x4";
715 pcie-4 {
716 nvidia,function = "pcie-x4";
720 pcie-5 {
721 nvidia,function = "usb3-ss";
725 pcie-6 {
726 nvidia,function = "usb3-ss";
736 sata-0 {
745 usb2-0 {
747 mode = "otg";
750 usb2-1 {
752 vbus-supply = <&vdd_5v0_rtl>;
753 mode = "host";
756 usb2-2 {
758 vbus-supply = <&vdd_usb_vbus>;
759 mode = "host";
762 usb2-3 {
764 mode = "host";
767 usb3-0 {
769 nvidia,lanes = "pcie-6";
773 usb3-1 {
775 nvidia,lanes = "pcie-5";