Lines Matching +full:pre +full:- +full:calibration
4 - compatible: Should be one of the following:
6 * "qcom,ipq4019-wifi"
7 * "qcom,wcn3990-wifi"
9 PCI based devices uses compatible string "qcom,ath10k" and takes calibration
10 data along with board specific data via "qcom,ath10k-calibration-data".
13 AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi"
15 "qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data"
16 to carry pre calibration data.
18 In general, entry "qcom,ath10k-pre-calibration-data" and
19 "qcom,ath10k-calibration-data" conflict with each other and only one
22 SNOC based devices (i.e. wcn3990) uses compatible string "qcom,wcn3990-wifi".
24 - reg: Address and length of the register set for the device.
25 - reg-names: Must include the list of following reg names,
27 - interrupts: reference to the list of 17 interrupt numbers for "qcom,ipq4019-wifi"
29 reference to the list of 12 interrupt numbers for "qcom,wcn3990-wifi"
31 Must contain interrupt-names property per entry for
32 "qcom,ath10k", "qcom,ipq4019-wifi" compatible targets.
34 - interrupt-names: Must include the entries for MSI interrupt
36 name ("legacy") for "qcom,ath10k", "qcom,ipq4019-wifi"
40 - resets: Must contain an entry for each entry in reset-names.
42 - reset-names: Must include the list of following reset names,
49 - clocks: List of clock specifiers, must contain an entry for each required
50 entry in clock-names.
51 - clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref",
52 "wifi_wcss_rtc" for "qcom,ipq4019-wifi" compatible target and
53 "cxo_ref_clk_pin" and optionally "qdss" for "qcom,wcn3990-wifi"
55 - qcom,msi_addr: MSI interrupt address.
56 - qcom,msi_base: Base value to add before writing MSI data into
58 - qcom,ath10k-calibration-variant: string to search for in the board-2.bin
61 - qcom,ath10k-calibration-data : calibration data + board specific data
64 - qcom,ath10k-pre-calibration-data : pre calibration data as an array,
66 - <supply-name>-supply: handle to the regulator device tree node
67 optional "supply-name" are "vdd-0.8-cx-mx",
68 "vdd-1.8-xo", "vdd-1.3-rfa", "vdd-3.3-ch0",
69 and "vdd-3.3-ch1".
70 - memory-region:
73 Definition: reference to the reserved-memory for the msa region
75 - iommus:
77 Value type: <prop-encoded-array>
79 - ext-fem-name:
83 for example: "microsemi-lx5586", "sky85703-11"
85 - qcom,snoc-host-cap-8bit-quirk:
90 - qcom,xo-cal-data: xo cal offset to be configured in xo trim register.
92 - qcom,msa-fixed-perm: Boolean context flag to disable SCM call for statically
95 - qcom,coexist-support : should contain eithr "0" or "1" to indicate coex
97 - qcom,coexist-gpio-pin : gpio pin number information to support coex
105 - iommus:
107 Value type: <prop-encoded-array>
118 #interrupt-cells = <1>;
119 #size-cells = <2>;
120 #address-cells = <3>;
125 qcom,ath10k-calibration-data = [ 01 02 03 ... ];
126 ext-fem-name = "microsemi-lx5586";
134 compatible = "qcom,ipq4019-wifi";
142 reset-names = "wifi_cpu_init",
151 clock-names = "wifi_wcss_cmd",
171 interrupt-names = "msi0", "msi1", "msi2", "msi3",
178 qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
179 qcom,coexist-support = <1>;
180 qcom,coexist-gpio-pin = <0x33>;
186 compatible = "qcom,wcn3990-wifi";
188 reg-names = "membase";
190 clock-names = "cxo_ref_clk_pin";
204 vdd-0.8-cx-mx-supply = <&pm8998_l5>;
205 vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
206 vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
207 vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
208 vdd-3.3-ch1-supply = <&vreg_l26a_3p3>;
209 memory-region = <&wifi_msa_mem>;
211 qcom,msa-fixed-perm;
212 wifi-firmware {