Lines Matching +full:multi +full:- +full:pmic

1 * Maxim MAX8998, National/TI LP3974 multi-function device
3 The Maxim MAX8998 is a multi-function device which includes voltage/current
5 other sub-blocks. It is interfaced using an I2C interface. Each sub-block
8 PMIC sub-block
9 --------------
11 The PMIC sub-block contains a number of voltage and current regulators,
17 - compatible: Should be one of the following:
18     - "maxim,max8998" for Maxim MAX8998
19     - "national,lp3974" or "ti,lp3974" for National/TI LP3974.
20 - reg: Specifies the i2c slave address of the pmic block. It should be 0x66.
23 - interrupts: Interrupt specifiers for two interrupt sources.
24   - First interrupt specifier is for main interrupt.
25   - Second interrupt specifier is for power-on/-off interrupt.
26 - max8998,pmic-buck1-dvs-gpios: GPIO specifiers for two host gpios used
29 - max8998,pmic-buck2-dvs-gpio: GPIO specifier for host gpio used
32 - max8998,pmic-buck1-default-dvs-idx: Default voltage setting selected from
36 - max8998,pmic-buck2-default-dvs-idx: Default voltage setting selected from
40 - max8998,pmic-buck-voltage-lock: If present, disallows changing of
43 Additional properties required if max8998,pmic-buck1-dvs-gpios is defined:
44 - max8998,pmic-buck1-dvs-voltage: An array of 4 voltage values in microvolts
47 Additional properties required if max8998,pmic-buck2-dvs-gpio is defined:
48 - max8998,pmic-buck2-dvs-voltage: An array of 2 voltage values in microvolts
55 	regulator-name {
59 Following regulators of the MAX8998 PMIC block are supported. Note that
63 	- LDOn
64 		  - valid values for n are 2 to 17
65 		  - Example: LDO2, LDO10, LDO17
66 	- BUCKn
67 		  - valid values for n are 1 to 4.
68 		  - Example: BUCK1, BUCK2, BUCK3, BUCK4
70 	- ENVICHG: Battery Charging Current Monitor Output. This is a fixed
73 	- ESAFEOUT1: (ldo19)
74 	- ESAFEOUT2: (ld020)
76 	- CHARGER: main battery charger current control
84 	pmic@66 {
85 		compatible = "maxim,max8998-pmic";
87 		interrupt-parent = <&wakeup_eint>;
91 		max8998,pmic-buck1-default-dvs-idx = <0>;
92 		max8998,pmic-buck1-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */
94 		max8998,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
98 		max8998,pmic-buck2-default-dvs-idx = <0>;
99 		max8998,pmic-buck2-dvs-gpio = <&gpx0 0 3 0 0>; /* SET3 */
100 		max8998,pmic-buck2-dvs-voltage = <1350000>, <1300000>;
105 				regulator-name = "VDD_ALIVE_1.1V";
106 				regulator-min-microvolt = <1100000>;
107 				regulator-max-microvolt = <1100000>;
108 				regulator-always-on;
112 				regulator-name = "VDD_ARM_1.2V";
113 				regulator-min-microvolt = <950000>;
114 				regulator-max-microvolt = <1350000>;
115 				regulator-always-on;
116 				regulator-boot-on;
120 				regulator-name = "CHARGER";
121 				regulator-min-microamp = <90000>;
122 				regulator-max-microamp = <800000>;