Lines Matching +full:pex +full:- +full:bias
4 -------------------
5 - compatible: Must be "ams,as3722".
6 - reg: I2C device address.
7 - interrupt-controller: AS3722 has internal interrupt controller which takes the
8 interrupt request from internal sub-blocks like RTC, regulators, GPIOs as well
10 - #interrupt-cells: Should be set to 2 for IRQ number and flags.
12 of AS3722 are defined at dt-bindings/mfd/as3722.h
14 interrupts.txt, using dt-bindings/irq.
17 --------------------
18 - ams,enable-internal-int-pullup: Boolean property, to enable internal pullup on
20 - ams,enable-internal-i2c-pullup: Boolean property, to enable internal pullup on
23 - ams,enable-ac-ok-power-on: Boolean property, to enable exit out of power off
34 Please refer to pinctrl-bindings.txt in this directory for details of the
41 -------------------
42 - gpio-controller: Marks the device node as a GPIO controller.
43 - #gpio-cells: Number of GPIO cells. Refer to binding document
47 --------------------
50 - pinctrl-names: A pinctrl state named "default" be defined, using the
51 bindings in pinctrl/pinctrl-bindings.txt.
52 - pinctrl[0...n]: Properties to contain the phandle that refer to
58 various pin configuration parameters, such as pull-up,
63 - pins: List of pins. Valid values of pins properties are:
68 function, bias-disable, bias-pull-up, bias-pull-down,
69 bias-high-impedance, drive-open-drain.
72 gpio, interrupt-out, gpio-in-interrupt,
73 vsup-vbat-low-undebounce-out,
74 vsup-vbat-low-debounce-out,
75 voltage-in-standby, oc-pg-sd0, oc-pg-sd6,
76 powergood-out, pwm-in, pwm-out, clk32k-out,
77 watchdog-in, soft-reset-in
87 -------------------
91 vsup-sd2-supply: Input supply for SD2.
92 vsup-sd3-supply: Input supply for SD3.
93 vsup-sd4-supply: Input supply for SD4.
94 vsup-sd5-supply: Input supply for SD5.
95 vin-ldo0-supply: Input supply for LDO0.
96 vin-ldo1-6-supply: Input supply for LDO1 and LDO6.
97 vin-ldo2-5-7-supply: Input supply for LDO2, LDO5 and LDO7.
98 vin-ldo3-4-supply: Input supply for LDO3 and LDO4.
99 vin-ldo9-10-supply: Input supply for LDO9 and LDO10.
100 vin-ldo11-supply: Input supply for LDO11.
103 ---------------------------------
105 sd[0-6], ldo[0-7], ldo[9-11]
107 Each sub-node should contain the constraints and initialization
109 of standard properties for these sub-nodes.
111 ams,ext-control: External control of the rail. The option of
120 are defined @dt-bindings/mfd/as3722.h
122 ams,enable-tracking: Enable tracking with SD1, only supported
125 Power-off:
130 ams,system-power-controller: Boolean, to enable the power off functionality
134 --------
135 #include <dt-bindings/mfd/as3722.h>
141 ams,system-power-controller;
143 interrupt-parent = <&intc>;
144 interrupt-controller;
145 #interrupt-cells = <2>;
147 gpio-controller;
148 #gpio-cells = <2>;
150 pinctrl-names = "default";
151 pinctrl-0 = <&as3722_default>;
157 bias-pull-down;
163 bias-pull-up;
173 vsup-sd2-supply = <...>;
177 regulator-name = "vdd_cpu";
178 regulator-min-microvolt = <700000>;
179 regulator-max-microvolt = <1400000>;
180 regulator-always-on;
181 ams,ext-control = <2>;
185 regulator-name = "vdd_core";
186 regulator-min-microvolt = <700000>;
187 regulator-max-microvolt = <1400000>;
188 regulator-always-on;
189 ams,ext-control = <1>;
193 regulator-name = "vddio_ddr";
194 regulator-min-microvolt = <1350000>;
195 regulator-max-microvolt = <1350000>;
196 regulator-always-on;
200 regulator-name = "avdd-hdmi-pex";
201 regulator-min-microvolt = <1050000>;
202 regulator-max-microvolt = <1050000>;
203 regulator-always-on;
207 regulator-name = "vdd-1v8";
208 regulator-min-microvolt = <1800000>;
209 regulator-max-microvolt = <1800000>;
210 regulator-always-on;