Lines Matching +full:sync +full:- +full:in +full:- +full:gpios

7 It is typically used in conjunction with one or more demodulator and tuner devices
14 - compatible	: Should be "stih407-c8sectpfe"
16 - reg		: Address and length of register sets for each device in
17 		  "reg-names"
19 - reg-names	: The names of the register addresses corresponding to the
20 		  registers filled in "reg":
21 			- c8sectpfe: c8sectpfe registers
22 			- c8sectpfe-ram: c8sectpfe internal sram
24 - clocks	: phandle list of c8sectpfe clocks
25 - clock-names	: should be "c8sectpfe"
26 See: Documentation/devicetree/bindings/clock/clock-bindings.txt
28 - pinctrl-names	: a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num)
30 - pinctrl-0	: phandle referencing pin configuration for this tsin configuration
31 See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
36 - tsin-num	: tsin id of the InputBlock (must be between 0 to 6)
37 - i2c-bus	: phandle to the I2C bus DT node which the demodulators & tuners on this tsin channel are…
38 - reset-gpios	: reset gpio for this tsin channel.
42 - invert-ts-clk		: Bool property to control sense of ts input clock (data stored on falling edge of…
43 - serial-not-parallel	: Bool property to configure input bus width (serial on ts_data<7>).
44 - async-not-sync	: Bool property to control if data is received in asynchronous mode
47 - dvb-card		: Describes the NIM card connected to this tsin channel.
51 /* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */
54 		compatible = "st,stih407-c8sectpfe";
56 		reg-names = "stfe", "stfe-ram";
58 		interrupt-names = "stfe-error-irq", "stfe-idle-irq";
59 		pinctrl-0	= <&pinctrl_tsin0_serial>;
60 		pinctrl-1	= <&pinctrl_tsin0_parallel>;
61 		pinctrl-2	= <&pinctrl_tsin3_serial>;
62 		pinctrl-3	= <&pinctrl_tsin4_serial_alt3>;
63 		pinctrl-4	= <&pinctrl_tsin5_serial_alt1>;
64 		pinctrl-names	= "tsin0-serial",
65 				  "tsin0-parallel",
66 				  "tsin3-serial",
67 				  "tsin4-serial",
68 				  "tsin5-serial";
70 		clock-names = "c8sectpfe";
74 			tsin-num		= <0>;
75 			serial-not-parallel;
76 			i2c-bus			= <&ssc2>;
77 			reset-gpios		= <&pio15 4 GPIO_ACTIVE_HIGH>;
78 			dvb-card		= <STV0367_TDA18212_NIMA_1>;
82 			tsin-num		= <3>;
83 			serial-not-parallel;
84 			i2c-bus			= <&ssc3>;
85 			reset-gpios		= <&pio15 7 GPIO_ACTIVE_HIGH>;
86 			dvb-card		= <STV0367_TDA18212_NIMB_1>;