Lines Matching +full:hsic +full:- +full:state

4 - compatible: Should contain one of the following:
5   - "nvidia,tegra186-pmc": for Tegra186
6   - "nvidia,tegra194-pmc": for Tegra194
7   - "nvidia,tegra234-pmc": for Tegra234
8 - reg: Must contain an (offset, length) pair of the register set for each
9   entry in reg-names.
10 - reg-names: Must include the following entries:
11   - "pmc"
12   - "wake"
13   - "aotag"
14   - "scratch"
15   - "misc" (Only for Tegra194 and later)
18 - nvidia,invert-interrupt: If present, inverts the PMU interrupt signal.
19 - interrupt-controller: Identifies the node as an interrupt controller.
20 - #interrupt-cells: Specifies the number of cells needed to encode an
28 		compatible = "nvidia,tegra186-pmc";
33 		reg-names = "pmc", "wake", "aotag", "scratch";
39 		nvidia,invert-interrupt;
46 used to set pad power state and signaling voltage. A pad can be either
47 in active or power down mode. The support for power state and signaling
55 Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
58 csia		csib		dsi		mipi-bias
59 pex-clk-bias	pex-clk3	pex-clk2	pex-clk1
60 usb0		usb1		usb2		usb-bias
61 uart		audio		hsic		dbg
62 hdmi-dp0	hdmi-dp1	pex-cntrl	sdmmc2-hv
65 dsif		spi		ufs		dmic-hv
66 edp		sdmmc1-hv	sdmmc3-hv	conn
67 audio-hv	ao-hv
70   - pins: A list of strings, each of which contains the name of a pad
74   - low-power-enable: Configure the pad into power down mode
75   - low-power-disable: Configure the pad into active mode
76   - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or
79     include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
81 Note: The power state can be configured on all of the above pads except
82       for ao-hv. Following pads have software configurable signaling
83       voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, audio-hv,
84       ao-hv.
86 Pad configuration state example:
88 		compatible = "nvidia,tegra186-pmc";
93 		reg-names = "pmc", "wake", "aotag", "scratch";
97 		sdmmc1_3v3: sdmmc1-3v3 {
98 			pins = "sdmmc1-hv";
99 			power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
102 		sdmmc1_1v8: sdmmc1-1v8 {
103 			pins = "sdmmc1-hv";
104 			power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
107 		hdmi_off: hdmi-off {
109 			low-power-enable;
112 		hdmi_on: hdmi-on {
114 			low-power-disable;
121 		pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
122 		pinctrl-0 = <&sdmmc1_3v3>;
123 		pinctrl-1 = <&sdmmc1_1v8>;
130 		pinctrl-0 = <&hdmi_off>;
131 		pinctrl-1 = <&hdmi_on>;
132 		pinctrl-names = "hdmi-on", "hdmi-off";