Lines Matching +full:frame +full:- +full:number
1 /* SPDX-License-Identifier: BSD-3-Clause-Clear */
3 * Copyright (c) 2018-2021 The Linux Foundation. All rights reserved.
4 * Copyright (c) 2021-2022 Qualcomm Innovation Center, Inc. All rights reserved.
153 * The id of the reo exit ring where the msdu frame shall push
174 * Filter pass Unicast data frame (matching rxpcu_filter_pass
178 * Filter pass Multicast data frame (matching rxpcu_filter_pass
182 * Filter pass BAR frame (matching rxpcu_filter_pass
186 * Field only valid when for the received frame type the corresponding
190 * Field only valid when for the received frame type the corresponding
202 * field in address search failure cache-only entry should
206 * If set, intra-BSS routing detection is enabled
224 * uffer management for WiFi-to-PPE routing.
227 * by a different subsystem, completely disabling WiFi-to-PPE
251 * The PN number.
282 * When set, the BSSID of the incoming frame matched one of
286 * This number indicates which one out of the 8 BSSID register
287 * values matched the incoming frame
298 * Field indicates what the reason was that this mpdu frame
307 * When set, the received frame was an NDP frame, and thus
318 * Set when RXPCU detected a version error in the Frame control
322 * When set, AST based lookup for this frame has found a valid
377 * AND Fragment_flag is set. The fragment number from the 802.11 header
382 * received frame
387 * Set if the from DS bit is set in the frame control.
392 * Set if the to DS bit is set in the frame control.
397 * Protected bit from the frame control.
401 * Retry bit from the frame control. Only valid when first_msdu is set
406 * The sequence number from the 802.11 header.
435 * The number of delimiters before this MPDU. Note that this
436 * number is cleared at PPDU start. If this MPDU is the first
437 * received MPDU in the PPDU and this MPDU gets filtered-in,
438 * this field will indicate the number of delimiters located
442 * an PPDU, this field will indicate the number of delimiters
446 * Received frame was part of an A-MPDU.
449 * Received frame is a BAR frame
460 * A-MPDU frame but a stand alone MPDU. Interior MPDU in an
461 * A-MPDU shall have both first_mpdu and last_mpdu bits set to
484 * Set if packet is not a non-QoS data frame. Only set when
488 * Set if frame type indicates either null data or QoS null
500 * Set if more bit in frame control is set. Only set when
512 * Set if the order bit in the frame control is set. Only
516 * U-APSD trigger frame
519 * Indicates that this data type frame is not encrypted even if
532 * Frame control field in header. Only valid when the field is marked valid.
538 * MAC addresses in the received frame. Only valid when corresponding
547 * RXOLE uses this to determine intra-BSS routing.
550 * Opaque service code between PPE and Wi-Fi
566 * data frames to multi-link addresses during decapsulation to eth/nwifi
569 * Multi-link receiver address1,2. Only valid when corresponding
573 * If not set, RXDMA shall perform error-routing for WDS packets
574 * as the sender is not authorized and might misuse WDS frame
788 * Field indicates what the reason was that this mpdu frame
807 * A-MPDU delimiter or the preamble length field for non-A-MPDU
814 * Classification failed due to truncated frame.
838 * of a dynamic A-MSDU when DA is compressed.
842 * of a dynamic A-MSDU when SA is compressed.
845 * The 16-bit type value indicating the type of L3 later
850 * TCP sequence number.
853 * TCP acknowledge number.
878 * Set if the to DS bit is set in the frame control.
894 * Number of bytes padded to make sure that the L3 header will
898 * Indicates the first MSDU of A-MSDU. If both first_msdu and
899 * last_msdu are set in the MSDU then this is a non-aggregated MSDU
900 * frame: normal MPDU. Interior MSDU in an A-MSDU shall have both
904 * Indicates the last MSDU of the A-MSDU. MPDU end status is only
908 * Set if the from DS bit is set in the frame control.
930 * The id of the reo exit ring where the msdu frame shall push
946 * Set by RXOLE if it stripped 4-bytes of C-VLAN Tag from the
950 * Set by RXOLE if it stripped 4-bytes of S-VLAN Tag from the
954 * Indicates that this is an 802.11 fragment frame. This is
955 * set when either the more_frag bit is set in the frame control
956 * or the fragment number is not zero. Only set when first_msdu
971 * Number of MSDU's aggregated so far
1004 * A-MSDU could not be properly de-agregated.
1014 * Opaque service code between PPE and Wi-Fi
1020 * This packet needs intra-BSS routing by SW as the 'vdev_id'
1026 * to support intra-BSS routing with multi-chip multi-link
1054 * This field is still valid for MPDU frames without A-MSDU.
1083 * Indicates the MSDU number within a MPDU. This value is
1084 * reset to zero at the start of each MPDU. If the number of
1085 * MSDU exceeds 255 this number will wrap using modulo 256.
1107 * number is non-zero. If set indicates that this is a fragmented
1119 * 0 - Toeplitz hash of 2-tuple (IP source address, IP
1121 * 1 - Toeplitz hash of 4-tuple (IP source address,
1124 * 2 - Toeplitz of flow_id
1125 * 3 - Zero is used
1128 * Fixed 20-byte IPv4 header or 40-byte IPv6 header parsed
1137 * Fixed 20-byte TCP (excluding TCP options) or 8-byte UDP
1151 * 2 bytes of C-VLAN Tag Control Information from WHO_L2_LLC
1154 * 2 bytes of S-VLAN Tag Control Information from WHO_L2_LLC
1192 * 0 - spatial stream not used for this reception
1193 * 1 - spatial stream used for this reception
1199 * are all valid. This bit is in the last 64-bit of the descriptor
1203 * Toeplitz hash of 5-tuple
1205 * destination port, L4 protocol} in case of non-IPSec.
1207 * In case of IPSec - Toeplitz hash of 4-tuple
1226 * IPv4/IPv6 - Either, Toeplitz hash computed over 2-tuple
1228 * hash computed over 4-tuple IPv4 or IPv6 src/dest addresses
1231 * is the one used for hash-based REO routing (see use_flow_id_toeplitz_clfy
1240 * A-MPDU frame but a stand alone MPDU. Interior MPDU in an
1241 * A-MPDU shall have both first_mpdu and last_mpdu bits set to
1264 * Set if packet is not a non-QoS data frame. Only set when
1268 * Set if frame type indicates either null data or QoS null
1280 * Set if more bit in frame control is set. Only set when
1288 * Set if number of MSDUs in A-MSDU is above a threshold or if the
1293 * Set if the order bit in the frame control is set. Only
1297 * Indicates that the WiFi frame has one of the following errors
1310 * with the actually received number of bytes in the MPDU.
1329 * Indicates that an A-MSDU with 'from DS = 0' had an SA mismatching
1330 * TA or an A-MDU with 'to DS = 0' had a DA mismatching RA
1337 * Indicates that this data type frame is not encrypted even if
1353 * Indicates that the MPDU was pre-maturely terminated
1378 * Frame is received, but RXPCU could not update the receive bitmap